ADT Security Services Safewatch Pro 3000 Entrepreneur 3000 User Manual

							K5309V3   6/02  Model SASW3000EN
1
6DIHZDWFK3URŠ(1
(QWUHSUHQHXU(1
6HFXULW\0DQDJHU(1
6HFXULW\6\VWHPV
8VHU·V*XLGH
Meets ADT Security Services Triple Standards
Requirements:
CUSLISTED  Standards for Security and Fire
  Standard for False Alarm Reduction
7 167-0495:110California State Fire Marshal Approval 
						

							– 2 –
IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible
point of entry to a home or commercial premises. This would include any
skylights that may be present, and the upper windows in a multi-level building.
In addition, we recommend that radio backup be used in a security system so
that alarm signals can still be sent to the Customer Care Center in the event
that the telephone lines are out of order (alarm signals are normally sent over
the phone lines).
EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat detectors
have played a key role in reducing fire deaths in the United States. With regard
to the number and placement of smoke/heat detectors, we subscribe to the
recommendations contained in the National Fire Protection Associations
National Fire Alarm Code (NFPA 72). These recommendations can be found on
page 34 of this manual.
$ERXW7KLV0DQXDO
This manual is a step-by-step guide that will acquaint you with the systems
features and benefits. It defines the components and their functions, describes
their operation, and provides clear step-by-step instructions for normal and
emergency procedures. Keep this manual in a convenient place so that you can
refer to it as necessary. 
						

							– 3 –
7DEOHRI&RQWHQWV
System Overview....................................................................................................................5
Introduction
..........................................................................................................................5
System Basics
.......................................................................................................................5
Using the Voice Message Center
.........................................................................................7
About The Touchpads
...........................................................................................................8
General Information
.............................................................................................................8
Functions of the Touchpads
..............................................................................................10
Entry/Exit Delays
.................................................................................................................12
Entry Delay
.........................................................................................................................12
Exit Delay
............................................................................................................................12
Exit Alarms
.........................................................................................................................13
Checking For Open Zones
..................................................................................................14
Using the [*] Key to Display and Announce System Status
............................................14
Arming the System
...............................................................................................................15
Stay Mode: Arms Perimeter Only, Entry Delay On
.........................................................15
Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones
.......................................15
Instant Mode: Arms Perimeter Only, Entry Delay Off
....................................................15
Away Mode: Arms Entire System, Entry Delay On
.........................................................15
Arming Commands
.............................................................................................................16
Single Button Arming
........................................................................................................17
Single-Button “Step” Arming
.............................................................................................17
Using the Keyswitch
............................................................................................................18
Using the Keyswitch
...........................................................................................................18
Disarming and Silencing Alarms
......................................................................................19
Using the [OFF] key
...........................................................................................................19
Bypassing Protection Zones
..............................................................................................20
Using the BYPASS Key
......................................................................................................20
Quick Bypass
......................................................................................................................21
Chime Mode
...........................................................................................................................22
Viewing Current Date and Time
......................................................................................23
Viewing the Current Date and Time
.................................................................................23
Setting the Date and Time
.................................................................................................23
Panic Keys
..............................................................................................................................24 
						

							– 4 –
Table of Contents
Macro Key Programming & Usage...................................................................................25
About Macro Keys
...............................................................................................................25
Example of Macro Programming
.......................................................................................26
Using a Programmed Macro Key
.......................................................................................26
Using Device Commands
....................................................................................................27
Paging Feature
.....................................................................................................................28
About Automatic Paging
....................................................................................................28
About Manual Paging
.........................................................................................................29
Latch Key Paging
...............................................................................................................29
Security Codes & Authority Levels
..................................................................................30
About Security Codes
.........................................................................................................30
Authority Level Definitions
...............................................................................................30
How To Assign User Codes and Attributes
.......................................................................31
Accessing Other Partitions  (GOTO Command and Multi-Partition Arming)
......32
About Accessing Partitions
................................................................................................32
Using the GoTo Command
.................................................................................................33
Multi-Partition Arming
......................................................................................................33
Common Zone Operation
....................................................................................................34
Scheduling
.............................................................................................................................35
About Scheduling
................................................................................................................35
Creating Schedules
.............................................................................................................35
Event Logging Procedures
.................................................................................................37
About Event Logging
..........................................................................................................37
Viewing the Event Log
.......................................................................................................37
Table of Event Log Codes
...................................................................................................38
Testing the System (To Be Conducted Weekly)
............................................................39
Trouble Conditions
..............................................................................................................41
Maintaining Your System
...................................................................................................44
Fire Alarm System (If Installed)
.......................................................................................45
Quick Guide to Basic System Functions
........................................................................49
Summary of Audible/Visual Notifications
......................................................................50
Regulatory Statements and Warnings
............................................................................52
Charts of Your System’s Features
....................................................................................54 
						

							– 5 –
6\VWHP2YHUYLHZ
,QWURGXFWLRQ
Congratulations on your ownership of an ADT Partitioned Security System. Youve
made a wise decision in choosing it, for it represents the latest in security protection
technology today, and millions of premises are protected by ADT systems.
This system provides:
·Three forms of protection: burglary, fire* and emergency.
·At least one touchpad which provides control of system operation and displays
the system’s status
·Various sensors for perimeter and interior burglary protection
·Smoke or combustion detectors* designed to provide early warning in case of fire.
Your system may also have been programmed to automatically send alarm or status
messages over the phone lines to a Customer Care Center.
* Commercial installations and some residential systems may not include fire
protection – check with your installer.
6\VWHP%DVLFV
Burglary Protection
·There are four modes of burglary protection: Stay, Night-Stay, Away, Instant.
STAY: arms perimeter zones only and entry delay is on
INSTANT: same as STAY, except entry delay is off
NIGHT-STAY: arms perimeter zones and selected interior zones; entry delay on
AWAY: arms perimeter and all interior zones, entry delay is on
·You can BYPASS selected zones while leaving the rest of the system armed.
·CHIME mode alerts you to the opening of protected doors and windows while the
system is disarmed.
Fire Protection
·Fire protection is always active (if installed) and an alarm sounds if a fire
condition is detected
·If necessary, you can manually initiate a fire alarm using the touchpad (if
programmed).
·Refer to the Fire Alarm System section for information regarding fire protection,
smoke detectors and planning emergency exit routes.
Security Codes
·You were assigned a 4-digit security code during system installation.
·Use your security code when arming and disarming the system, and when
performing other system functions.
·Other users can be assigned different security codes.
·User codes can be assigned different authority levels, which define which system
functions a particular user can perform. 
						

							– 6 –
6\VWHP2YHUYLHZ&RQWLQXHG
Zones and Partitions
·The system sensing devices have been assigned to various “zones,” which are
specific areas of protection (e.g., front door, kitchen window, etc.).
·Zone numbers are displayed at the touchpad when an alarm or trouble condition
occurs on a sensor.
·Partitions provide two independent areas of protection, with each partition
containing a group of zones that can be armed and disarmed without affecting
other zones or users.
·Partitioned systems can include a common zone area, which is an area shared by
users of both partitions (such as a lobby in a building).
·Partition identification: 1 = partition 1; 2 = partition 2; 3 = common zone.
Arming, Step-Arming and Disarming Burglary Protection
·The system must be armed before the burglary protection can sense intrusions.
·To arm your system, enter your user code followed by the desired arming key.
·If programmed, the [#] key can be pressed instead of entering the security code
when arming the system.
·You can also use the step-arming key to arm the system, if programmed.
·To disarm the system, enter your user code then press the [OFF] key.
·Step-arming, if programmed, lets you use a function key to arm the system in one
of three modes by simply pressing the key repeatedly, where:
first press arms STAY; second press arms NIGHT-STAY; third press arms
AWAY.
Alarms
·When an alarm occurs, both the touchpad and external sounders will sound, and
the touchpad will display the zone(s) causing the alarm.
·If your system is connected to a Customer Care Center, an alarm message will
also be sent.
·To stop the alarm sounding, simply disarm the system.
Memory of Alarm
·When an alarm condition occurs, the touchpad displays the number(s) of the
zone(s) that caused the problem, and displays the type of alarm (e.g., “FIRE”).
·The message remains displayed even after disarming the system, but can be
cleared with another “off” sequence.
Function Keys
·The  “A”, “B”, “C”, and “D” keys on the touchpad can be programmed to perform
various functions.
·Functions include: activate a Panic alarm; arm the system; provide step arming;
switch lights on/off; send a message to a pager; display Time/Date; start a Macro 
						

							– 7 –
6\VWHP2YHUYLHZ&RQWLQXHG
Phone Access
·If included, a phone module permits you to access the system via a touch-tone
phone, either on-premises or by call-in when away.
·When you call in, the phone module announces system status over the telephone,
and you can arm/disarm the system and perform most function commands
remotely using the telephone keys.
·Complete information for using these features is provided with the voice module.
Paging Feature
·If programmed, the system can automatically send certain system condition
messages to up to four pagers.
·The display consists of code numbers that identify the type of condition that has
occurred.
Scheduling
·Your system can be programmed to automatically perform certain functions (e.g.,
arm the system) at a predetermined time each day.
8VLQJWKH9RLFH0HVVDJH&HQWHU
The Voice Touchpads feature a voice message
center that lets you record and playback one
message.
·The message can be up to 2.5-minutes long
·The message remains in the Touchpad’s memory
until a new message is recorded.
·The volume control of the message is adjustable.
·
Refer to the procedures below when using the
Message Center functions.6160VADT-50-003-V0
23
456
789
0
#
STAY
BYPASS
CHIME
INSTANTAWAY
CODETEST
READYARMED
READY
MIC MESSAGERECORD VOLUME
PLAY
S TAT U SFUNCTION VOICE1OFF
VOLUME
KEY
VOICE
KEY
STATUS
KEYFUNCTION
KEYDOWN
VOLUME PLAY KEY
AND
UP VOLUME RECORD
KEY SPEAKER
LCD
DISPLAY
MICROPHONE LEDs
Message Center Functions
To… Press these keys… Notes…
record a
message[#] FUNCTION + [0] VOICE + [1] RECORDThe red MESSAGE LED lights.
Message remains in memory
until a new message is recorded.
end
recording[1] RECORDThe red MESSAGE LED flashes,
indicating message waiting.
play a
message[#] FUNCTION + [0] VOICE + [3] PLAYThe recorded message plays and
the red MESSAGE LED turns off.
adjust the
volume[#] FUNCTION + [0] VOICE + [2] VOLUME keys,
then press volume key [3] ­
 (up) or [6] ¯
 (down)Adjusting message volume also
adjusts status volume. Volume
cannot be adjusted while playing. 
						

							– 8 –
$ERXW7KH7RXFKSDGV
*HQHUDO,QIRUPDWLRQ
Your touchpads allow you to control all system functions and feature the following:
· A telephone style (digital) keypad
· Liquid Crystal Display (LCD) which shows the nature and location of all
occurrences
· Built-in sounder which will sound during alarms and troubles. The sounder also
beeps during certain system functions and when depressing any of the keys (to
acknowledge the key press).
· Backlighting of the LCD display windows. Backlighting turns on when any key is
pressed, and when opening an entry/exit door while the system is armed. This
feature is helpful when a touchpad is located in a dimly lit area.
· Some touchpads have a voice feature that announces the nature and location of all
occurences. Voice touchpads also announce any faulted zones when Chime mode is
on. Ask your installer if this option has been programmed for your system.
IMPORTANT:
 If the touchpad beeps rapidly upon entering the  premises, it indicates that
an alarm has occurred during your absence and an intruder may still be on the premises.
LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.
Your touchpads are functionally the same, but may have different types of displays,
depending on the type installed with your system. To access the keys on the touchpad,
simply open the swing-down door.
Custom English
2-line Custom English display touchpads feature a 2-line,
Display
32-character alphanumeric LCD which displays system
messages in friendly English. These touchpads can also be
programmed with custom zone descriptors.
English Display
English display touchpads are functionally identical to Custom
English display touchpads, but the LCD display uses pre-
designated words to identify the nature and location of
occurrences.
Voice Touchpads
Voice Touchpads (if installed), are functionally the same as other
touchpads, except that these touchpads can provide the following:
·Voice announcements of system status (see Checking for Open
Zones section)
·Voice chime, which can alert you to the opening of doors and
windows while the system is disarmed (see Voice Chime in
Chime mode section)
·Message center, which lets you record and playback messages
(see Using the Voice Message Center in the System Overview
section). 
						

							– 9 –
$ERXW7KH7RXFKSDGV&RQWLQXHG
(QJOLVKLVSOD\7RXFKSDG
AW AY: All burglary zones, interior and
perimeter, are armed.
STAY: Perimeter burglary zones, such as
protected windows and doors, are
armed.
INSTANT: Entry delay is turned off:
Lit with STAY = Instant mode
Lit with AWAY = Maximum mode
ALARM
FIRE
AWAY
BYPASS
STAY
CHECK INSTANT NO AC
TEST
NOT READY
CHIME   BAT
ENGLISH DISPLAY TOUCHPAD
BYPASS: This appears when one or more burglary protection zones have been
bypassed.
NOT READY:Appears when burglary portion of the system is not ready for arming
(due to open protection zones). The system is ready to arm when this
message disappears and the READY indicator light comes on.
NO AC: Appears when AC power has been cut off. System is operating on
backup battery power.
AC: Appears when AC power is present.
CHIME: Appears when the CHIME feature is activated.
BAT: Low battery condition in a wireless sensor (if zone number displayed)
or low system battery (if no zone number displayed).
AL ARM: Appears when an intrusion has been detected and the system is armed
(also appears during a fire alarm or audible emergency alarm).
Accompanied by the protection zone in alarm.
CHECK: Appears when a malfunction is discovered in the system at any time or
if an open is detected in a FIRE zone at any time or a fault in a
DAY/NIGHT burglary zone during a disarmed period. Accompanied by
a display of zone number in trouble.
FIRE:Appears when a fire alarm is present. Accompanied by a display of the
zone in alarm.
A FIRE display also appears when a fire alarm is manually activated,
accompanied by a display of emergency key zone number programmed
for fire. 
						

							– 10 –
)XQFWLRQVRIWKH7RXFKSDGV
NOTE:
 The functions printed directly on the keys
indicate their primary purpose (most require entry ofa security code first); the functions printed undersome keys (shown in brackets in the list below)indicate an alternate function available on voicetouchpads only.
1.DISPLAY WINDOW.
Custom English Display Touchpads:
  2-line, 32-
character Liquid Crystal Display (LCD) touchpads
that display protection point identification, system
status, and messages.
English Display Touchpads:
 Display protection
zone ID and system status messages using pre-
designated words in the LCD display.
2.1 OFF     Disarms burglary portion of the system,
 silences alarms and audible trouble indicators,
and  clears visual display after problems
correction.
[RECORD] Used to record up to a 2.5-minute
message.
3.2 AWAY   Arms the entire burglary
 system,
perimeter and interior.
[VOLUME] Used with the desired ­
 [3] or ¯
 [6] keys
to set playback and system announcement volume.
4.3 STAY     Arms perimeter portion of burglary
system only. Interior protection is not armed,
 allowing  movement within premises without
causing an alarm.
[PLAY] Used to playback a recorded message.
[­
] Used with VOLUME key to raise volume.
5.4            
This is not a Function key. Used only as
a numeric key.
6.5  TEST    Tests the system and alarm sounder if
 disarmed. Refer to Testing The System
 section for
test procedures.
7.6 BYPASS Removes individual protection zones
 from being monitored by the system.
[¯
]Used with VOLUME key to lower volume.
8.7INSTANT Arms in manner similar to the STAY
mode, but without the entry delay feature.
Entering via an entry/exit door will cause an
instant alarm.
9.8
 CODE    Used to assign additional user codes
for other users of the system.
10.9 CHIME
   
Turns CHIME mode on and off.
When  on, the opening of windows or doors while
the system is disarmed will sound 3 beeps at the
touchpad(s).
11.  
#   This key can be used for Quick Arming of
the system without use of a
security code (if programmed).
[FUNCTION] Used to enable voice and volume
functions.
12. Key   
0   [VOICE] Used to activate the
RECORD, VOLUME, and PLAY functions.
13.*
 READY  Used to display all open protection
 zones.
[STATUS] Used to announce system status and
faulted zones (if any exist).
14.KEYS 0–9:
 Numeric keys used to enter your
security code(s).
15.MIC:
 Microphone for Message Center recordings.
16. MESSAGE LED:
 (red). Flashes red when
message waiting or lights steady red when
recording a message.
17.READY INDICATOR:
 (green) Lit when the
system is 
ready to be armed (no faults present).
While the system is disarmed, this indicator will
go on and off as protection zones are closed and
opened.
18.ARMED INDICATOR:
 (red) Lit when the
system has been armed.
19.FUNCTION KEYS: Keys A, B, C, D may have
been programmed for a variety of functions,
including panic (emergency) functions. For details,
see the Function Keys
 section.
20.INTERNAL SPEAKER:
 The built-in speaker
mimics the alarm sounder during alarms, and will
also beep during certain system functions. The
speaker also provides voice playback for any
recorded messages.