ADS XiLog User Manual August 2011 QR 775026 A0

ADS XiLog+ System  User Manual 
 55 
 
7.  Feed the battery cable f rom the new battery through the hole in the 
battery holder. 
8.  Place and properly position the battery into the holder. 
9.  Insert the battery holder back  into the XiLog+, and secure it with the 
two screws.  
10.  Connect the battery cable to the circuit board . 
11.  Slide  the circuit board into the rails inside the housing . 
12.  Place the yellow cover back onto the XiLog+ and into position. 
13.  Turn the yellow cover...

ADS XiLog+ System User Manual 
 56 
  

ADS XiLog+ System  User Manual 
 57 
C H A P T E R  5  
9 -Channel Connections  
Two options are available for wiring the outputs on the XiLog+ 9 : 
•  NXG- 302 Expansion Box  
•  NXG- 303 Bare Wire Cable 
NXG-302 Expansion Box  
ADS offers an expansion box for the wiring.  Make connections based on the 
figures below.  Seal any unused connectors on the box with a blank to prevent 
damage to the connection box. 
  

ADS XiLog+ System User Manual 
 58 
 
Note:   Each voltage input has a 2- , 5-, or 10- volt range,  based on the 
position of the jumper next to the appropriate input.  Verify the correct 
position.  Selecting the wrong position could r esult in damage to the 
logger. 
NXG-303 Bare Wire Cable  
  

ADS XiLog+ System  User Manual 
 59 
 
R  represents the following:  
V= 0 -2 volts; R=0Ω  
V= 0 -5 volts; R=69k8Ω , ±0.1%, 25ppm 
V= 0 -10 volts; R=187k Ω, ±0.1%, 25ppm   

ADS XiLog+ System User Manual 
 60 
 
  

ADS XiLog+ System  User Manual 
 61 
C H A P T E R  6  
Appendices 
T his chapter contain s import ant instructional and referenc e information 
regarding the XiLog+ FastTrack  software, meter scaling, battery life, and 
airfreight restrictions.   

ADS XiLog+ System User Manual 
 62 
 Appendix  A:  XiLog+  FastTrack Software 
The XiLog+ FastTrack  software primarily  is designed for expediting the 
process of programming the logger , viewing the current logger configuration, 
and testing the signal strength.   Although the PrimeWorks configuration 
process is much more comprehensive, FastTrack  represents an efficient and 
effective alternative for deploy ing and/or testing the logger quic kl y in the 
field.  
Note:   The XiLog+ FastTrack...

ADS XiLog+ System  User Manual 
 63 
Viewing the Current Configuration 
To view the current configuration programmed into the logger, click on the 
View  button at the bottom of the XiLog+ FastTrack  application window.  
Programming the Logger 
1. Edit the name of the logger in the Site Name  field, when necessary. 
2.  Edit the phone number (when applicable) in the Phone N umber field. 
3.  Designate the parameters under the Transmission  header in the 
following way:  
  Enter the time at which the...

ADS XiLog+ System User Manual 
 64 
 Select the interval at  which the data will be logged and averaged  (as 
necessary) from the Interval  drop-down list.  Sending  5- or 10-
minute data will require sending more than one SMS per channel 
per day.   Choosing Off  will prevent the channel from recording 
measurements.  
5.  Designate the parameters under the Pressure Channel 1  header in the 
following wa y: 
  Select the unit of meas ure in which to log the data from the Units  
drop- down list. 
...