Adam Equipment GK Indicator GKREVL1 User Manual

 
59                              © Adam Equipment Company 2013 
1.18.8 F8 –ZERO  MODE  
 
To enter this parameter, press the  [Tare] key when “ F8 ZEm” is shown. 
Select  the  Zero  mode  desired.  In  all  but  special  ca ses  Zero  Mode  1  is  used.      The 
other 2 zero modes are for unique locations in the  world and effect the +/- range of 
the zero.      
Press the  [Func] key to change the value. 
Press  [Tare]  to accept the displayed value. 
Press  [Zero]  to return to weighing. 
  
1.18.9...

 
60                              © Adam Equipment Company 2013 
1.18.10 F10 –CALIBRATION COUNT (GK-M ONLY) 
This parameter allows the calibration and parameter  counting function to be active.  
To enter this parameter, press the  [Tare] key when  “F10  Cn” is shown. 
The display will show if the Calibration Counting   Mode is set to on or oFF. If On the 
Calibration  count  and  Parameter  count  will  be  seen  at  power  on  as  described  in 
section  6.0.    If  set  to  Off  the  only  method...

 
61                              © Adam Equipment Company 2013 
REPLACEMENT PARTS AND ACCESSORIES 
If you need to order any spare parts and accessorie s, contact your supplier or Adam 
Equipment. A partial list of such items is as follo ws- 
 
·  Main Power cord or adaptor for  
USA versions. 
·   Replacement Battery  ·
  In use cover 
·   Printer, etc. 
 
  

 
62                              © Adam Equipment Company 2013 
SERVICE INFORMATION 
This manual covers the details of operation. If you  have a problem with the indicator 
that  is  not  directly  addressed  by  this  manual  then  contact  your  supplier  for 
assistance.  In  order  to  provide  further  assistance,   the  supplier  will  need  the 
following information which should be kept ready: 
 
A. Details of your company 
 
   -Name of your company: 
    -Contact person’s name:  
    -Contact...

 
63                              © Adam Equipment Company 2013 
WARRANTY INFORMATION    
Adam  Equipment  offers  Limited  Warranty  (Parts  and  L abour)  for  the  components  failed  due  to  defects 
in materials or workmanship.  Warranty starts from the date of delivery. 
 
During the warranty period, should any repairs be n ecessary, the purchaser must inform  its supplier or 
Adam  Equipment  Company.  The  company  or  its  authoris ed  Technician  reserves  the  right  to  repair  or 
replace...

64  © Adam Equipment Company 2013  

65  © Adam Equipment Company 2013
 
APPENDIX 
PARAMETER  LAYOUT for  GK / GFK SCALES Press  the [Func]  key  to 
e\fter F\b\fctio\fs mode. 
K
 ey f\b\fctio\fs while i\f this sectio\f 
[Tar\f] e\fter a parameter or accept the cha\fges 
[Func ] move to \fext parameter or optio\f 
[Z\fro]  ret\br\f to previo\bs parameter or ret\br\f to weighi\fg 
FUNC 1  Check weighi\fg parameters F1 LLk 
Limit Lock  oFF  
P

St (pre-set)  F2 L\fd 
LED display  bAr 
(Bar type) 
S
 pot (spot type) 
S
 PEA (whole segme\ft) F3...

66  © Adam Equipment Company 2013
  

67  Adam Equipment Company 2013 
Adam Equipment  
 ADAM EQUIPMENT, Maidstone Road, 
Kingston Milton Keynes, MK10 0BD U.K. 

Tel: (01908) 274545        Fax: (01908) 641339 
Intl Tel:   -44 1908 -274545   Intl Fax: -44 1908 641339 
E-Mail Address: [email protected] 
D eclaration of Conformity   Verklaring van overeenstemming 
Konformitätserklärung   Dichiarazione di Conformità 
Déclaration de Conformité   Declaración de Conformidad 
The non-automatic weighing instrument          Het niet...

68  Adam Equipment Company 2013