3M Multimedia Projector S10 Operators Manual

11
1Connect the connector of the
power cord to the AC inlet of the
projector. 

2Firmly plug the power cord’s plug
into the outlet.
WARNING• Please use extra caution when connecting the power cord as
incorrect or faulty connections may result in FIRE and/or ELECTRICAL SHO\
CK. Please
adhere to the “Product Safety Guide” and the following. 
• Only plug the power cord into outlets rated for use with the power \
cord’s specified
voltage range.
• Only use the power cord that came with the projector. If it...

12
CAUTIONAlways handle the batteries with care and use them only as directed.
Improper use may result in battery cracking or leakage, which could result in fire, injury
and/or pollution of the surrounding environment.
• Keep the battery away from children and pets.
• Be sure to use only the batteries specified for use with the remote control. Do not mix
new batteries with used ones.
• When inserting batteries, verify that the plus and minus terminals are aligned correctly
(as indicated in the remote...

13
Operating The Remote Control
ATTENTION• Do not drop or otherwise expose the remote control to physical
impact.
• Do not get the remote control wet or place it on wet objects. Doing\
 so may result in
malfunction.
• Remove the batteries from the remote control and store them in a sa\
fe place if you
won’t be using the remote control for an extended period.
• Replace the batteries whenever the remote control starts to malfunc\
tion.
• When strong lights, such as direct sunlight or light from an extrem\...

14
Power ON/OFF
Turning On The Power
WARNING• When the power is ON, a strong light is emitted. Do not look into the
lens or vents of the projector.
• Turn the power on/off in right order. Please power on the projector before
the connected devices. Power off the projector after the connected devices.NOTE
1Make sure that the power cord is
firmly and correctly connected to the
projector and outlet.
2Set the power switch to [ | ] (ON). 
3Press the  button of the projector or
the remote control. 
The...

15
VIDEO
ASPECT
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
ON
VIDEO
ASPECT
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
ON
Selecting An Input Signal
1
2Use the zoom ring to adjust the screen
size.
3Use the focus ring to focus the picture.
Press the RGB button of the remote
control or rgb button of the projector.
When the button is pressed, the projector switches to
the 
rgb port.
Selecting a RGB signal
Press the VIDEO button of the remote
control or video button of the projector.
As illustrated...

16
Turning Off The Power
• Turn the power on/off in right order. Please power on the projector before
the connected devices. Power off the projector after the connected devices.NOTE
1Press the  button of the projector or
the remote control.
The message “Power off?” will appear on the screen
for approximately 5 seconds.
2Press the STANDBY/ON button again
while “Power off?” the message is
visible. 
The projector lamp will go off, and the power
indicator will begin blinking orange.
Then the powerindicator...

17
Operating
Adjusting The Volume
Temporarily Muting The Sound
1Press the VOLUME button.
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
2Use the /
buttons to adjust the
volume.
Press the VOLUME button again to close the dialog and
complete this operation.
(Even if you dont do anything, the dialog will
automatically disappear after a few seconds.)
Press this to increase the volume
Press this to decrease the volume
16
VOLUME
16
VOLUME
VOLUMEV O LU M E...

18
Adjusting The Position
1Press the POSITION button.
As illustrated on the right, a dialog will appear on the screen
to aid you in adjusting the position.
2Use the,,,
buttons to adjust
the position.
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB input....

19
Using The Automatic Adjustment Feature
Correcting Keystone Distortions
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
MENU
POSITION
ENTER
ESC RESET
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
MENU
POSITION
ENTER
ESC RESET
VOLUME
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
• The automatic adjustment operation requires approximately 10 second\
s.
Also, please note that it may not function correctly with some input.NOTE
1Press the AUTO button.
Horizontal position (H POSITION),...

20
Using The Magnify Feature
Freezing The Screen
1Press the MAGNIFY (ON) button.
The projector enters MAGNIFY mode.
2Press the POSITION button, then use the
,,,
buttons to select the area
to zoom. Press the POSITION button again
to finalize the zoom area.
3Use the ,
buttons to adjust the zoom
level.
Press the MAGNIFY (OFF) button to exit MAGNIFY
mode and restore the screen to normal.(The
projector will also automatically exit MAGNIFY
mode if there is a change in the input signals
state.)
ON...