3M Multimedia Projector S10 Operators Manual

Thank you for purchasing this projector.• The in\borm\ftion in \tthis m\fnu\fl is subje\tct to ch\fnge without n\totice.
• The m\fnu\b\fcturer \fss\tumes no responsibili\tty \bor \fny errors th\ft m\t\fy \fppe\fr in this m\fn\tu\fl. 
• The reproduction, t\tr\fnsmission or use o\b \tthis document or conte\tnts is not permitted \twithout
express written \futhor\tity.
TRADEMARK ACKNOWLEDGMENT :
• VGA \fnd XGA \fre re\tgistered tr\fdem\frks o\b t\the Intern\ftion\fl Busine\tss M\fchines Corpor\ftion.\t
•...

Projector Featuresœ œœ
œœ
œœ
œœ
œœ
œœ
œ
3
Preparationœ œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œ
3
Part Namesœ œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œ
4
The Projectorœœœœœœœœœ4
Attaching The Baseœœœœœœ4
The Remote Controlœœœœœœ6
Setting Upœ œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œœ
œ
7
Arrangementœœœœœœœœœ7
Adjusting The Projector’s 
Elevatorœœœœœœœœœœœ8
Connecting Your Devicesœœœœ9
Connecting Power Supplyœœœ11
Remote...

3
Ultra High BrightnessCrisp, ultra-bright presentations is achieved by using a UHB (ultra hig\
h brightness) lamp and a highly
efficient optical system.
Whisper Mode EquippedSpecial mode is available for reducing projector noise to achieve quiete\
r operation.
User Memory FunctionThis projector can memorize 4 settings by MY MEMORY function.
Partial Magnification FunctionInteresting parts of images can be magnified for closer viewing. 
Keystone Distortion CorrectionQuick correction of distorted...

4
Part Names
The ProjectorIndicates the corresponding
reference page
Attaching The Base
Zoom knob
Focus ring
Air filter cover
(An air filter is
inside.)

Elevator
button
Elevator feet
Lens
(The picture is
projected from
here.) Remote sensor

Projector (Front/Right)
1Turn off the projector, and unplug the power cord. Allow the
lamp bulb to cool for at least 45 minutes.
2After making sure that the projector
has cooled adequately, slowly flip
over the projector, so that the bottom
is facing up....

5
AC inlet
video port 
audio port
(from a computer) 
s-video port
component video - Y
component video - CB/PB
component video - CR/PR
audio            R port L port
(from a video equipment)

Power switch
rgb port
control port
Projector (Rear/Left)
Part Names (continued)
The Projector (continued)
Control buttons
power indicator
tells the state of power
supply. Refer to the section
“Power ON/OFF”.
reset button
cancels the adjustment in
progress.
* The adjustments of the
volume etc....

6
The Remote Control
STANDBY/ON
button
prepares for turning the
power on/off.
VIDEO button
toggles between the signal 
ports of video, s-video
and component video.
MENU button
opens/closes the menu.
RGB button
selects the input signal of
rgbport.
BLANK button
blanks the screen
temporarily.
SEARCH button
searches for an input
signal between the
following signal ports of
rgb, video, s-videoand
component video.
VOLUME button
turns on/off the VOLUME
mode.
In the VOLUME mode,
To adjust the volume,
use the...

7
Setting Up
Arrangement
WARNING• Install the projector in a suitable environment according to
instructions of the “Product Safety Guide” and this manual.
• The power outlet should be close to the projector and easily access\
ible.
Refer to the illustrations and tables below to determine the screen size\
 and projection
distance.
The values shown in the table are calculated for a full size screen:800 ·600
(a):Distance from the projector to the screen (±10%)
(b):Distance from the lens center to the...

8
Adjusting The Projectors Elevator
CAUTION• If you press the elevator buttons without holding the projector, the
projector might crash down, overturn, smash your fingers and possibly result in
malfunction. To prevent damaging the projector and injuring yourself, ALWAYS HOLD
THE PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
You can use the elevator feet to make adjustments if the surface on which you need to set
the projector is uneven or if you otherwise need to adjust the...

9
Connecting Your Devices
WARNING• Incorrect connecting could result in fire or electrical shock.
Whenever attempting to connect other devices to the projector, please th\
oroughly read
the Product Safety Guide, this manual and the manual of each device to\
 be
connected. CAUTION
• TURN OFF ALL DEVICES prior to connecting them to the projector.
Attempting to connect a live device to the projector may generate extrem\
ely loud
noises or other abnormalities that may result in malfunction and/or dama\
ge to...

10
Please refer to the following for connecting your devices.
See the rear of the projector. You can see the ports.

L-audio-R video
s-video audio
Y
   component video
CB/PBCR/PR
rgbcontrol
L-audio-R video
s-video audio
Y
   component video
CB/PBCR/PR
rgbcontrol
L-audio-R video
s-video audio
Y
   component video
CB/PBCR/PR
rgbcontrol
L-audio-R video
s-video audio
Y
   component video
CB/PBCR/PR
rgbcontrol
L-audio-R video
s-video audio
Y
   component video
CB/PBCR/PR
rgbcontrol
L-audio-R video
s-video...