3M Multimedia Projector S10 Operators Manual

							11
1Connect the connector of the
power cord to the AC inlet of the
projector. 

2Firmly plug the power cord’s plug
into the outlet.
WARNING• Please use extra caution when connecting the power cord as
incorrect or faulty connections may result in FIRE and/or ELECTRICAL SHO\
CK. Please
adhere to the “Product Safety Guide” and the following. 
• Only plug the power cord into outlets rated for use with the power \
cord’s specified
voltage range.
• Only use the power cord that came with the projector. If it is dama\
ged, contact your
dealer to newly get correct one.
• Never modify the power cord. Never attempt to defeat the ground con\
nection of the
three-pronged plug.
• Make sure that you firmly connect the power cord to the projector a\
nd wall outlet.
AC Inlet Connector Side

Connecting Power Supply
Setting Up (continued)
4&O
 
 
 
 1.
 
 
						

							12
CAUTIONAlways handle the batteries with care and use them only as directed.
Improper use may result in battery cracking or leakage, which could result in fire, injury
and/or pollution of the surrounding environment.
• Keep the battery away from children and pets.
• Be sure to use only the batteries specified for use with the remote control. Do not mix
new batteries with used ones.
• When inserting batteries, verify that the plus and minus terminals are aligned correctly
(as indicated in the remote control).
• When you dispose the battery, you should obey the law in the relative area or country.
1Remove the
battery cover.
Slide back and
remove the battery
cover in the direction
of the arrow.
Insert the
batteries.
Align and insert the two
AA batteries according to
their plus and minus
terminals (as indicated in
the remote control).
Close the
battery cover.
Replace the battery
cover in the direction
of the arrow and
snap it back into
place.
23
Remote Control
Putting Batteries
4&O
 
 
 
 1.
 
 
						

							13
Operating The Remote Control
ATTENTION• Do not drop or otherwise expose the remote control to physical
impact.
• Do not get the remote control wet or place it on wet objects. Doing\
 so may result in
malfunction.
• Remove the batteries from the remote control and store them in a sa\
fe place if you
won’t be using the remote control for an extended period.
• Replace the batteries whenever the remote control starts to malfunc\
tion.
• When strong lights, such as direct sunlight or light from an extrem\
ely close range
(such as from an inverter fluorescent lamp), hit the projector’s re\
mote sensor, the
remote control may cause to function. Adjust the direction of the projec\
tor to keep light
from directly hitting the projector’s remote sensor.
• The remote control works with the projector’s remote sensor.
• The range of the remote sensor is 3 meters with a 60- degree range (30 degrees to the left and right of the
remote sensor). Also a remote signal reflected in the screen etc. may be
available. If it is difficult to send a remote signal to the
sensor directly, please try.
• Since the remote control uses infrared light to send signals to the projector (Class1 LED), be sure to use the
remote control in an area free from obstacles that could
block the remote control’s output signal to the projector.
à Ã
approximately
3 meters
Remote sensor
Remote Control (continued)
4&O
 
 
 
 1.
 
 
						

							14
Power ON/OFF
Turning On The Power
WARNING• When the power is ON, a strong light is emitted. Do not look into the
lens or vents of the projector.
• Turn the power on/off in right order. Please power on the projector before
the connected devices. Power off the projector after the connected devices.NOTE
1Make sure that the power cord is
firmly and correctly connected to the
projector and outlet.
2Set the power switch to [ | ] (ON). 
3Press the  button of the projector or
the remote control. 
The projector lamp will light up and the power
indicator will begin blinking green.
According to a setup, the projector lamp may light
up and the powerindicator may begin blinking
green, without pressing this button.
When the power is completely on, the indicator will
stop blinking and light green.
The powerindicator will light orange.
Power switch (ON position)
VIDEO
ASPECT
VOLUME STANBY/ON
MAGNIFY
AUTO BLANK RGB SEARCH
ON
(STANDBY/ON) button
Power switch
(on/off)button  
power 
indicator
4&O
 
 
 
 1.
 
 
						

							15
VIDEO
ASPECT
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
ON
VIDEO
ASPECT
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
ON
Selecting An Input Signal
1
2Use the zoom ring to adjust the screen
size.
3Use the focus ring to focus the picture.
Press the RGB button of the remote
control or rgb button of the projector.
When the button is pressed, the projector switches to
the 
rgb port.
Selecting a RGB signal
Press the VIDEO button of the remote
control or video button of the projector.
As illustrated below, each time you press the button,
the projector switches between its input signal ports.
Select the signal you wish to project.
Selecting a video signal
video                   s-video
com
ponent video
RGB button
VIDEO button
Power ON/OFF (continued)
rgb bu tton
video button
Zoom knobFocus ring
4&O
 
 
 
 1.
 
 
						

							16
Turning Off The Power
• Turn the power on/off in right order. Please power on the projector before
the connected devices. Power off the projector after the connected devices.NOTE
1Press the  button of the projector or
the remote control.
The message “Power off?” will appear on the screen
for approximately 5 seconds.
2Press the STANDBY/ON button again
while “Power off?” the message is
visible. 
The projector lamp will go off, and the power
indicator will begin blinking orange.
Then the powerindicator will stop blinking and light
to solid orange when the lamp cooling is complete.
3Switch the power switch to [O] (OFF). 
The powerindicator will go off.
Power switch (OFF position)
Power ON/OFF (continued)
VIDEO
ASPECT
VOLUME STANBY/ON
MAGNIFY
AUTO BLANK RGB SEARCH
ON
(STANDBY/ON) button
Power switch
(on/off)button  
power 
indicator
4&O
 
 
 
 1.
 
 
						

							17
Operating
Adjusting The Volume
Temporarily Muting The Sound
1Press the VOLUME button.
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
2Use the /
buttons to adjust the
volume.
Press the VOLUME button again to close the dialog and
complete this operation.
(Even if you dont do anything, the dialog will
automatically disappear after a few seconds.)
Press this to increase the volume
Press this to decrease the volume
16
VOLUME
16
VOLUME
VOLUMEV O LU M E
1Press the MUTE button.
Press the MUTE button.
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound. 
(If you dont do anything, the dialog will automatically
disappear after a few seconds.)
Press the MUTE or VOLUME button to restore the sound.
VOLUME
16
MUTEMUTE
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
MENU
POSITION
ENTER
ESC RESET
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
MENU
POSITION
ENTER
ESC RESET
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
4&O
 
 
 
 1.
 
 
						

							18
Adjusting The Position
1Press the POSITION button.
As illustrated on the right, a dialog will appear on the screen
to aid you in adjusting the position.
2Use the,,,
buttons to adjust
the position.
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation.  (Even if you dont do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB input.
POSITION
POSITION
• When a menu is displayed, the operation of adjusting the position works
for the position of not the picture but the menu.NOTE
VIDEO
ASPECT
MUTE
KEYSTONE FREEZE
MENU POSITION
ENTER
ESC RESET
VOLUME STANBY/ON
MAGNIFY
AUTO BLANK RGB SEARCH
OFFON
Operating (continued)
4&O
 
 
 
 1.
 
 
						

							19
Using The Automatic Adjustment Feature
Correcting Keystone Distortions
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
MENU
POSITION
ENTER
ESC RESET
VOLUME
STANBY/ON
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
VIDEO
ASPECT
MUTE
KEYSTONE
FREEZE
MENU
POSITION
ENTER
ESC RESET
VOLUME
MAGNIFY
AUTO BLANK
RGB SEARCH
OFF ON
• The automatic adjustment operation requires approximately 10 second\
s.
Also, please note that it may not function correctly with some input.NOTE
1Press the AUTO button.
Horizontal position (H POSITION), vertical position (V POSITION),
clock phase (H PHASE) and horizontal size (H SIZE) are
automatically adjusted.
Make sure that the application window is set to its maximum size
prior to attempting to use this feature. Dark pictures may still be
incorrectly adjusted. Use a bright screen when adjusting.
The signal type best suited for the respective input signal is
selected automatically.
This feature is available only if VIDEO is set to AUTO in the INPUT
menu.
Automatic Adjustment for RGB Input
Automatic Adjustment for Video Input
AUTO
1Press the KEYSTONE button.As illustrated on the right, a dialog will appear on
the screen to aid you in correcting the distortion.
2Use the  ,
buttons to correct distortion. Press the KEYSTONE button again to close the dialog
and complete this operation. (Even if you dont do
anything, the dialog will automatically disappear after
a few seconds.)
KEYSTONE
+0
KEYSTONE
• When the WIDE is selected under the ASPECT item of the MAIN menu, t\
his
adjustment is ignored.
• The correcting keystone distortions function may not be work well w\
ith some types of
input signals.
• The adjustable range for correcting keystone distortions will vary \
with the type of input signal.NOTE
Operating (continued)
4&O
 
 
 
 1.
 
 
						

							20
Using The Magnify Feature
Freezing The Screen
1Press the MAGNIFY (ON) button.
The projector enters MAGNIFY mode.
2Press the POSITION button, then use the
,,,
buttons to select the area
to zoom. Press the POSITION button again
to finalize the zoom area.
3Use the ,
buttons to adjust the zoom
level.
Press the MAGNIFY (OFF) button to exit MAGNIFY
mode and restore the screen to normal.(The
projector will also automatically exit MAGNIFY
mode if there is a change in the input signals
state.)
ON
MAGNIFYMAGNIFY
POSITIONPOSITION
• The projector will automatically exit from MAGNIFY mode if either the
SEARCH, RGB, AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the
input signals state.
• The correcting keystone condition may vary when the magnify function is active. In
this case, please make the magnify OFF, so the correcting keystone condition will be
restored.NOTE
• The freezing function will automatically finish if either the STANDBY/ON,
SEARCH, RGB, VIDEO, BLANK, AUTO, VOLUME, MUTE, POSITION or MENU button of
remote control is pressed, or if a button of projector is pressed, or if there is a change
in the input signal’s state.
• If the projector continues projecting the same image for a long time (i.e. you forget to
exit FREEZE mode), the image might possibly remain as an afterimage. Do not leave
the projector in FREEZE mode for too long.NOTE
VIDEO
ASPECT
MUTE
KEYSTONE FREEZE
MENU POSITION
ENTER
ESC RESET
VOLUME STANBY/ON
MAGNIFY
AUTO BLANK RGB SEARCH
OFFON
1Press the FREEZE button.
The [II] icon appears and the screen will freeze
at the current image. Press the FREEZE button
again and the [    ] appears as the projector exits FREEZE
mode.MUTE
KEYSTONE FREEZE
MENU POSITIONOFFON
FREEZE
Û
Operating (continued)
4&O
 
 
 
 1.