ZyXEL Router Prestige 334 User Manual

Prestige 334 User’s Guide
Chapter 22 Internet Access220
22.3  Configuring the PPTP Client
To configure a PPTP client, you must configure the My Login and Password fields for a PPP 
connection and the PPTP parameters for a PPTP connection. 
After configuring My Login and Password for PPP connection, press [SPACE BAR] and 
then [ENTER] in the Encapsulation field in Menu 4 -Internet Access Setup to choose 
PPTP as your encapsulation option. This brings up the following screen.
Gateway IP AddressEnter the...

Prestige 334 User’s Guide
221Chapter 22 Internet Access
Figure 100   Internet Access Setup (PPTP) 
The following table contains instructions about the new fields when you choose PPTP in the 
Encapsulation field in menu 4.
22.4  Configuring the PPPoE Client
If you enable PPPoE in menu 4, you will see the next screen. For more information on PPPoE, 
please see the appendix.
Menu 4 - Internet Access Setup
       ISPs Name= MyISP
       Encapsulation= PPTP
         Service Type= N/A
         My Login=...

Prestige 334 User’s Guide
Chapter 22 Internet Access222
Figure 101   Internet Access Setup (PPPoE)
The following table contains instructions about the new fields when you choose PPPoE in the 
Encapsulation field in menu 4.
If you need a PPPoE service name to identify and reach the PPPoE server, please go to menu 
11 and enter the PPPoE service name provided to you in the Service Name field.
22.5  Basic Setup Complete
Well done! You have successfully connected, installed and set up your Prestige to...

Prestige 334 User’s Guide
223Chapter 22 Internet Access 

Prestige 334 User’s Guide
Chapter 23 Remote Node Configuration 224
CHAPTER23
Remote Node Configuration
This chapter covers remote node configuration.
23.1  Introduction to Remote Node Setup
A remote node is required for placing calls to a remote gateway. A remote node represents 
both the remote gateway and the network behind it across a WAN connection. Note that when 
you use menu 4 to set up Internet access, you are actually configuring a remote node. The 
following describes how to configure Menu 11.1...

Prestige 334 User’s Guide
225 Chapter 23 Remote Node Configuration
Figure 102   Menu 11.1 Remote Node Profile for Ethernet Encapsulation
The following table describes the fields in this menu.
                       Menu 11.1 - Remote Node Profile
   Rem Node Name= MyISP                 Route= IP
   Active= Yes
   Encapsulation= Ethernet              Edit IP= No
   Service Type= Standard               Session Options:
   Service Name= N/A                      Edit Filter Sets= No
   Outgoing:
     My...

Prestige 334 User’s Guide
Chapter 23 Remote Node Configuration 226
23.2.2  PPPoE Encapsulation
The Prestige supports PPPoE (Point-to-Point Protocol over Ethernet). You can only use 
PPPoE encapsulation when you’re using the Prestige with a DSL modem as the WAN device. 
If you change the Encapsulation to PPPoE, then you will see the next screen. Please see the 
appendix for more information on PPPoE.
Figure 103   Menu 11.1 Remote Node Profile for PPPoE Encapsulation
23.2.2.1  Outgoing Authentication...

Prestige 334 User’s Guide
227 Chapter 23 Remote Node Configuration
23.2.2.2  Nailed-Up Connection
A nailed-up connection is a dial-up line where the connection is always up regardless of traffic 
demand. The Prestige does two things when you specify a nailed-up connection. The first is 
that idle timeout is disabled. The second is that the Prestige will try to bring up the connection 
when turned on and whenever the connection is down. A nailed-up connection can be very 
expensive for obvious reasons....

Prestige 334 User’s Guide
Chapter 23 Remote Node Configuration 228
Figure 104   Menu 11.1 Remote Node Profile for PPTP Encapsulation
The next table shows how to configure fields in menu 11.1 not previously discussed.
23.3  Edit IP
Move the cursor to the Edit IP field in menu 11.1, then press [SPACE BAR] to select Ye s. 
Press [ENTER]
 to open Menu 11.3 - Remote Node Network Layer Options. 
                     Menu 11.1 - Remote Node Profile
   Rem Node Name= MyISP                 Route= IP
   Active=...

Prestige 334 User’s Guide
229 Chapter 23 Remote Node Configuration
Figure 105   Menu 11.3 Remote Node Network Layer Options for Ethernet Encapsulation
This menu displays the My WAN Addr field for PPPoE and PPTP encapsulations and 
Gateway IP Addr field for Ethernet encapsulation.  The following table describes the fields 
in this menu.
 Menu 11.3 - Remote Node Network Layer Options
             IP Address Assignment= Dynamic
             IP Address= N/A
             IP Subnet Mask= N/A...