Home > Zanussi > Fridge freezer > Zanussi Zrg 314 Sw User Manual

Zanussi Zrg 314 Sw User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Zanussi Zrg 314 Sw User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 276 Zanussi manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Important!  Defrost the freezer when the frost layer reaches
    a thickness of about 3-5 mm.
    To remove the frost, do these steps:
    1. Switch off the appliance.
    2. Remove any stored food, wrap it in several layers of
    newspaper and put it in a cool place.
    3. Leave the door open.
    4. When defrosting is completed, dry the interior thor-
    oughly and refit the plug.
    5. Switch on the appliance.
    6. Set the temperature regulator to obtain the maximum
    coldness and run the appliance for two or three hours
    using this setting.
    7. Reload the previously removed food into the com-
    partment.
    Important!  Never use sharp metal tools to scrape off frost
    from the evaporator as you could damage it. Do not usea mechanical device or any artificial means to speed up
    the thawing process other than those recommended by
    the manufacturer. A temperature rise of the frozen food
    packs, during defrosting, may shorten their safe storage
    life.
    Periods of non-operation
    When the appliance is not in use for long periods, take
    the following precautions:
    1. disconnect the appliance from electricity supply
    2. remove all food
    3. defrost and clean the appliance and all accessories
    4. leave the door/doors open to prevent unpleasant
    smells.
    Important!  If the cabinet will be kept on, ask somebody
    to check it once in a while to prevent the food inside from
    spoiling in case of a power failure.
    What to do if…
    Warning!  Before troubleshooting, disconnect the
    mains plug from the mains socket.
    Only a qualified electrician or competent person must do
    the troubleshooting that is not in this manual.Important!  There are some sounds during normal use
    (compressor, refrigerant circulation).
    ProblemPossible causeSolution
    The appliance is noisyThe appliance is not supported prop-
    erlyCheck if the appliance stands stable (all
    the four feet should be on the floor)
    The appliance does not operate.
    The lamp does not operate.The appliance is switched off.Switch on the appliance.
     The mains plug is not connected to the
    mains socket correctly.Connect the mains plug to the mains
    socket correctly.
     The appliance has no power. There is
    no voltage in the mains socket.Connect a different electrical appliance
    to the mains socket.
    Contact a qualified electrician.
    The lamp does not work.The lamp is in stand-by.Close and open the door.
     The lamp is defective.Refer to Replacing the lamp.
    The compressor operates con-
    tinually.The temperature is not set correctly.Set a higher temperature.
     The door is not closed correctly.Refer to Closing the door.
     The door has been opened too fre-
    quently.Do not keep the door open longer than
    necessary.
     41
     
    						
    							ProblemPossible causeSolution
     The product temperature is too high.Let the product temperature decrease to
    room temperature before storage.
     The room temperature is too high.Decrease the room temperature.
    Water flows on the rear plate of
    the refrigerator.During the automatic defrosting proc-
    ess, frost defrosts on the rear plate.This is correct.
    Water flows into the refrigerator.The water outlet is clogged.Clean the water outlet.
     Products prevent that water flows into
    the water collector.Make sure that products do not touch
    the rear plate.
    Water flows on the ground.The melting water outlet does not flow
    in the evaporative tray above the com-
    pressor.Attach the melting water outlet to the
    evaporative tray.
    The temperature in the appliance
    is too low.The temperature regulator is not set
    correctly.Set a higher temperature.
    The temperature in the appliance
    is too high.The temperature regulator is not set
    correctly.Set a lower temperature.
     The door is not closed correctly.Refer to Closing the door.
     The product temperature is too high.Let the product temperature decrease to
    room temperature before storage.
     Many products are stored at the same
    time.Store less products at the same time.
    The temperature in the refrigera-
    tor is too high.There is no cold air circulation in the
    appliance.Make sure that there is cold air circula-
    tion in the appliance.
    The temperature in the freezer is
    too high.Products are too near to each other.Store products so that there is cold air
    circulation.
    There is too much frost.Food is not wrapped correctly.Wrap the food correctly.
     The door is not closed correctly.Refer to Closing the door.
     The temperature regulator is not set
    correctly.Set a higher temperature.
    Replacing the bulb
    If you want to replace the bulb, do these steps:
    1. Break the circuit of the appliance.
    2. Unscrew the lamp cover securing screw.
    3. Unhook the moving part by pressing it as shown in
    the figure.
    4. Replace the bulb with one of the same power (the
    maximum power is shown on the light bulb cover)
    5. Fix the lamp cover in place.
    6. Screw the lamp cover securing screw.
    7. Reconnect the appliance.
    8. Open the door and check if the light comes on.
    42
     
     
    						
    							Closing the door
    1. Clean the door gaskets.
    2. If necessary, adjust the door. Refer to Installation.
    3. If necessary, replace the defective door gaskets. Con-
    tact the Service Center.
    Technical data
      ZRG314SWZRG714SW
    Dimension   
     Height850 mm850 mm
     Width550 mm550 mm
     Depth612 mm612 mm
    Rising Time 11 h11 h
    The technical information are situated in the rating plate
    on the internal left side of the appliance and in the energy
    label.
    Installation
    Caution!  Read the Safety Information carefully for
    your safety and correct operation of the appliance
    before installing the appliance.
    Positioning
    Install this appliance at a location where the ambient tem-
    perature corresponds to the climate class indicated on the
    rating plate of the appliance:
    Climate
    classAmbient temperature
    SN+10°C to + 32°C
    N+16°C to + 32°C
    ST+16°C to + 38°C
    T+16°C to + 43°C
    Levelling
    When placing the appli-
    ance ensure that it stands
    level. This can be achieved
    by two adjustable feet at
    the bottom in front (2). If
    necessary adjust the feet
    by removing the spacer
    (1).
    1
    2
     43
     
    						
    							Location
    The appliance should be installed well away from sources
    of heat such as radiators, boilers, direct sunlight etc. En-
    sure that air can circulate freely around the back of the
    cabinet. To ensure best performance, if the appliance is
    positioned below an overhanging wall unit, the minimum
    distance between the top of the cabinet and the wall unit
    must be at least 100 mm . Ideally, however, the appliance
    should not be positioned below overhanging wall units.
    Accurate levelling is ensured by one or more adjustable
    feet at the base of the cabinet.
    If the cabinet is placed in a corner and the side with the
    hinges facing the wall, the distance between the wall and
    the cabinet must be at least 10 mm to allow the door to
    open enough so that the shelves can be removed.Warning!
    It must be possible to dis-
    connect the appliance from
    the mains power supply; the
    plug must therefore be easi-
    ly accessible after installa-
    tion.
    min.100 mm
    15 mm
    15 mm
    Door reversibility
    Important!  To carry out the following operations, we
    suggest that this be made with another person that will
    keep a firm hold on the doors of the appliance during the
    operations.
    To change the opening direction of the door, do these
    steps:
    44
     
     
    						
    							1. Remove the plug from
    the power socket.
    2. Tilt back the appliance
    carefully so that the com-
    pressor cannot touch the
    floor.
    3. Unscrew both adjustable
    feet.
    4. Unscrew the screws of
    the door bottom hinge. Re-
    move the hinge. Put over
    the pin in the direction of
    the arrow.
    5. Unscrew and install the
    screw on the opposite side.
    6. Install the hinge on the
    opposite side.
    7. Screw both adjustable
    feet.8. Unscrew both screws on
    the rear side.
    9. Push back the top and lift
    it from the fixing elements.10. Unscrew the screws of
    the door top hinge.
    11. Remove the hinge. Put
    over the pin in the direction
    of the arrow. Install the
    hinge on the opposite side.
    12. Tighten the hinge.
    13. Put the top in position.
    14. Pull it forward.
    15. Screw both screws on
    the rear side.16. Remove and install the
    handle1) on the opposite
    side.
    17. Reposition, level the
    appliance, wait for at least
    four hours and then con-
    nect it to the power socket.
    1) If foreseen
    Do a final check to make sure that:
    • All screws are tightened.
    • The door opens and closes correctly.
    If the ambient temperature is cold (i.e. in Winter), the
    gasket may not fit perfectly to the cabinet. In that case,
    wait for the natural fitting of the gasket.In case you do not want to carry out the above mentioned
    operations, contact the nearest After Sales Service Force.
    The After Sales Service specialist will carry out the rever-
    sibility of the doors at your cost.
     45
     
    						
    							Reversibility of the freezer door
    180˚
    Electrical connection
    Before plugging in, ensure that the voltage and frequency
    shown on the rating plate correspond to your domestic
    power supply.
    The appliance must be earthed. The power supply cable
    plug is provided with a contact for this purpose. If the
    domestic power supply socket is not earthed, connect the
    appliance to a separate earth in compliance with current
    regulations, consulting a qualified electrician.
    The manufacturer declines all responsibility if the above
    safety precautions are not observed.
    This appliance complies with the E.E.C. Directives.
    Environmental concerns
    The symbol    on the product or on its packaging
    indicates that this product may not be treated as
    household waste. Instead it should be taken to the
    appropriate collection point for the recycling of electrical
    and electronic equipment. By ensuring this product is
    disposed of correctly, you will help prevent potentialnegative consequences for the environment and human
    health, which could otherwise be caused by inappropriate
    waste handling of this product. For more detailed
    information about recycling of this product, please
    contact your local council, your household waste disposal
    service or the shop where you purchased the product.
    46
     
     
    						
    							 47
     
    						
    							www.zanussi.com
    200383079-02-122009
     
    						
    All Zanussi manuals Comments (0)

    Related Manuals for Zanussi Zrg 314 Sw User Manual