Zanussi Zba 3160 Instruction Booklet

							electrolux 51GB
Maintenance
Unplug the appliance before
carrying out any maintenance
operation.
Warning
This appliance contains
hydrocarbons in its cooling unit
maintenance and recharging must
therefore only be carried out by
authorised technicians.
Defrosting
Bleeding part of the moisture of cooling
chamber in form of frost and ice goes
with the operation of the refrigerator.
Thick frost and ice has an insulating
effect, so it reduces cooling efficiency as
the temperature increases and it needs
more energy.
At this type of appliance defrosting
cooling compartment is automatic
without any external intervention.
The thermostatic control interrupts the
operation of compressor at regular
intervals for more or less time - during this
cooling is interrupted - temperature of the
cooling compartment increases and
defrosting occurs. After defrosting the
thermostatic control restarts operation of
the system.
Melting water flows through defrost water
outlet into the evaporative tray maintained
on the top of compressor and evaporates
due to warmth of it.
Check and clean the outlet of
melting water coming during
defrosting regularly. If it is clogged
the melting water gathered can cause
earlier failure as it can go to the
insulating of the appliance.
Clean the melting water outlet with the
supplied pipe scraper that can be seen in
the figure. The pipe scraper has to be
stored in the outlet.
Occasionally check the defrost water
outlet not to be clogged up.
The most typical case of clogging up in
the defrost water outlet when you put
food wrapped in some paper into the
appliance and this paper contacts back
plate of cooling compartment and
freezes to it. If you remove the food right
at this moment the paper will tear and it
can cause clogging up in the outlet by
getting into it. So you are asked to be
careful - because of the above - when
placing foods wrapped in paper into the
appliance.
In case of increased demand e.g.
during heatwaves, the refrigerator
temporarily happens to operate
constantly - during this the automatic
defrosting is ineffective.
Remaining small ice and frost stains on
back plate of the cooling compartment
after defrosting period is not abnormal.
 
						

							52electroluxGB
Cleaning
Never use metal objects for
cleaning your appliance as it
may get damaged.
NEVER use detergents, abrasive
powders, highly perfumed cleaning
products or wax polishes to clean the
interior as these will damage the
surface and leave a strong odour.nie
Metallgegenstände um das Gerät zu
reinigen, da es beschädigt werden
könnte. 
Clean the inside with warm water and
bicarbonate of soda. Rinse and dry
thoroughly.
To guarantee a safe operation of the
fridge, once a year remove the ventilation
grill at the base and clean the air
channels with a vacuum cleaner.
When the appliance is not in
use
Disconnect the appliance from the
electricity supply.
Empty all foods and clean the appliance,
leaving the doors ajar to prevent
unpleasant smells.
How to change the bulb
Should the light fail to work you can
change it as below:
Break the circuit of the appliance.
Unscrew the plate screw fixing the lamp
cover, then take the lamp cover off in the
direction of arrow and the bulb can be
changed. (Type of the bulb: Mignon 322,
230 V, 15 W, E 14 thread)
After changing bulb replace the lamp
cover, screw the plate screw and apply
voltage to the appliance.
The lack of light does not influence
operation of the refrigerator.
 
						

							electrolux 53GB
Something not Working
Problems may be due to causes
which can easily be solved before
calling the Technical Service. Please
follow these instructions:
SYMPTOM
Door does not close
It is too warm inside
the refrigerator
It is too cold inside the
refrigerator.
The compressor works
continuously.
There is water
inside/outside the
refrigerator.
Water comes out on
the floor.
NoisesSOLUTION
Level properly the appliances if it is not well levelled.
Weight surpasses the storage limit of the door shelf so spread weight
more evenly or take some products out.
The appliance is not properly installed. Please look in the “Building-
in” section.
Set a lower temperature.
Distribute the food products to allow cold air to circulate around them.
Make sure that the door is completely closed and that the insulating
strip is complete and clean.
The temperature where the cabinet is placed is above normal room
temperature.
Turn the temperature regulator to a warmer setting temporarily.
Turn the thermostat knob to a lower number.
The temperature where the cabinet is placed is above normal room
temperature.
Check that the ventilation is sufficient and that the ventilation
openings are unobstructed.
The cause could be the introduction of large quantities of food and/or
frequent opening/closing of the door.
Sometimes is normal. During automatic defrosting frost thaws on the
cooling plate.
Place the drain hose at the back of the cabinet above the drain bowl.
Sometimes this is normal. Temperature control may cause clicking
sounds when the system is connected or disconnected.
The injected cooling gas may produce a gurgling sound while passing
through the tubes.
The motor may cause a humming noise and/or slight bumping.
The insulation material used has a tendency to slighly increase noise
levels, how ever it allows for much better insulation and a lower
energy consumption.
 
						

							54electroluxGB
Customer service and spare
parts
If you cannot find the remedy for a
malfunction in these operating
instructions, please contact your dealer
or our customer service department and
consult the Guarantee card.
Selective ordering of replacement parts
can save unnecessary travel and costs.
For this reason always provide the
following appliance information:
Model Name
Model Number (PNC)
Serial Number (S-No.)
This information can be found on the
rating plate inside the cabenit on the left
hand wall. We recommend that you enter
this information here, so that it is handy if
needed.
Technical specifications
The technical data is indicated in the
rating plate on the left side inside the
appliance.
Door reversibility
The equipment is supplied with
the door opening toward the
right.
Follow the instructions below before
installing it to have the door open to
the left.
1. Unscrew the top hinge screw and
remove the spacer.
2. Remove the door.
3. Unscrew with a key the lower pin and
replace it on the opposite side.
4. Reinsert the door and screw the upper
hinge and spacer onto the opposite
side.
 
						

							electrolux 55GB
The climate classification can be found on
the rating plate, which is located inside
the cabinet on the left hand wall.
The following table shows which ambient
temperature is correct for each climate
classification:
Climate for an ambient
classification temperature of
SN +10 to +32 °C
N +16 to +32 °C
ST +16 to +38 °C
T +16 to +43 °C
Electrical connection 
Before plugging in, ensure that the
voltage and frequency shown on the
serial number plate correspond to your
domestic power supply.
Voltage can vary by ±6% of the rated
voltage.
For operation with different voltages, a
suitably sized auto-transformer must be
used.
Important
The appliance must be earthed.
The power supply cable plug is provided
with a contact for this purpose.
Installation
Take utmost care when handling
your appliance so as not to cause
any damages to the cooling unit with
consequent possible fluid leakages.
During normal operation, the
condenser and compressor at the
back of the appliance heat up
considerably. Always ensure that there
is adequate ventilation as a failure to do
this will result in component failure and
possible food loss. See installation
instructions.
Important: if the supply cord is
damaged, it must be replaced by a
special cord or assembly available
from the manufacturer or its service
agent.
Positioning
Unpack the cabinet and check that it is
in good condition and free of any
transport damage.
The appliance must not be located
close to radiators or gas cookers.
Avoid prolonged exposure of the
appliance to direct sunlight.
For safety reasons, minimum
ventilation must be as shown in Fig.
Attention: keep ventilation openings
clear of obstruction.
It is necessary that the niche is
provided with a conduct of venti-lation
having the following dimensions:
Depth: 50 mm
Width: 540 mm
 
						

							56electroluxGB
If the domestic power supply socket is
not earthed. connect the appliance to a
separate earth in compliance with current
regulations, consulting a specialist
technician.
The Manufacturer declines all
responsibility if the above safety
precautions are not observed.
This appliance complies with the
following E.E.C.
Directives:
- 87/308 EEC of 2/6/87 relative to
radio interference suppression.
- 73/23 EEC of 19.2.73 (Low Voltage
Directive) and subsequent
modifications.
- 89/336 EEC of 3.5.89
(Electromagnetic Compatibility
Directive) and subsequent
modifications.
It is necessary that the niche is provided
with a conduct of ventilation having the
following dimensions:
Depth 50 mm
Width 540 mm
For appropriate venting, follow
indications in the figure.
1. Fit the appliance in the niche by making
sure that it stands against the interior
surface of the unit on the side where the
door hinges of the appliances are fitted.
Insert the appliance until the upper strip
butts up against the unit (1) and make
Attention!
It must be possible to disconnect the appliance from the
mains power supply; the plug must therefore be easily
accessible after installation.
Building-in
Dimensions of the recess
Height of housing (1)
880 1225 mm
Depth of housing (2)
550 550 mm
Width of housing (3)
560 560 mm
 
						

							electrolux 57GB
sure that the lower hinge is in line with
the surface of the unit (2).
2. Open the door and push the appliance
against the side of kitchen furniture
opposite to that of the appliance hinges.
Fasten the appliance with 4 screws (I)
provided in the kit included with the
appliance. 
3. Press in the joint covers between the
appliance and the kitchen furniture.
4. From the plastic cover (E), which is
used to cover the hinge with the pivot
pin, you must take away the part as
indicated in the drawing.
This operation is made easer since
there is, in the internal part of the
cover hinge lid a groove that facilates
the removal of this coomponent.
"Remove the part marked with DX, if
the pivot pin is inserted in the right
hinge, SX in opposite case."
Apply covers (C-D) on joint cover lugs
and into hinge holes.Snap hinge
covers (E) into position.
5. Separate parts Ha, Hb, Hc, Hd as
shown in the figure.
 
						

							58electroluxGB
furniture door and mark the holes as
indicated in the figure. 
9. Remove the squares and mark a
distance of 8 mm from the outer edge
of the door where the nail must be
fitted (K).
10. Place the small square on the guide
again and fix it with the screws
supplied.
Should the alignment of the furniture
door be necessary, use the
clearance of slots.
At the end of this procedure, it is
necessary to check if the door of the
furniture closes properly.
6. Place guide (Ha) on the inside part of
the furniture door, up and down as
shown in the figure and mark the
position of external holes. After having
drilled holes, fix the guide with the
screws supplied.
7. Fix cover (Hc) on guide (Ha) until it
clips into place.
8. Open the appliance door and the
furniture door at 90°. Insert the small
square (Hb) into guide (Ha). Put
together the appliance door and the
N/Za/20-1. (09) 200382762 2009. 02. 02.
 
						

							11. Fix cover (Hd) on the small square
(Hb) until it clips into place.
electrolux 59GB
 
						

							200382762-01-02022009 
933 015 015
www.electrolux.com