Xerox WorkCentre 3045 Service Manual

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-27Error Troubleshooting
Scanner Test 2■ADF Motor -On
■ADF Motor -OffThis test checks the motor system for 
the ADF document handling.
All Test
■Start
■Processing
■Check OK or 
 ErrorThis test runs all ESS Diag tests except 
OP Panel, USB Host test, Lamp test, and 
the Scanner test. Test returns Check OK 
or failed test name.
IOT DiagTests for print engine components.
Sensor TestAt the start, 
L - 0 is displayed. 
When a sensor is 
turned...

2-28 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Error Troubleshooting
Edit NVM■Ad0000=00000000*
■Please waitDisplays current NVM values. Use this 
to edit NVM values.
Caution:  Change NVM values only 
when directed to do so by a 
troubleshooting procedure.
Save NVM to 
ESSSave NVM
■Save NVM MCU -> 
ESS OK?
■Saved
■Please waitSaves the MCU Board NVM to the IP 
Board temporarily when the MCU 
needs to be replaced.
Print InfoProvides printer configurations and settings...

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-29Error Troubleshooting
FAX/Scanner Diagnostic Tests
Skew ■-630 to 630 Adjusts the skew so that the image is 
parallel with both sides of the paper.
Life
Counter NameVa l u e
These counter values 
are reference only. Do 
not use as the official 
value.
M/C Total PV30000
M/C FC PV-
DEVE 
Roundtime-
XERO 
Roundtime-
M/C DispTime-
LM/C Pixel -
M/C 
ColorEmptyBW-
M/C Custom 
Start-
M/C Custom End-
Wa ste  To n e r-
To n e r  P VStd.:...

2-30 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Error Troubleshooting
Regi FB Lead -2.0 mm ~ 2.0 mm,
in 0.1 mm StepAdjusts Registration of the flatbed 
leading edge.
Regi FB Side -1.0 mm ~ 1.0 mm,
in 0.1 mm StepsAdjusting Registration of the flatbed 
side edge.
Auto RegistrationReports the result of auto registration 
which is performed while the printer 
powers up.
IIT I/O Check
■FB Home Sensor
■ADF Scan Sensor
■ADF Document 
Sensor
■ADF Cover SensorTests the scanner sensors....

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-31Error Troubleshooting
Ring DetectionFreq Range @ On Period 
-- Upper Bound27~85 Hz
Freq Range @ On Period 
-- Lower Bound13~20 Hz
Minimum On time 0: 100 ms, 1: 110 ms, 2: 120 ms,
3: 130 ms, 4: 140 ms, 5: 150 ms,
6: 160 ms, 7: 170 ms, 8: 180 ms,
9: 190 ms, 10: 200 ms, 11: 210 ms,
12: 220 ms, 13: 230 ms, 14: 240 ms,
15: 250 ms
Off time 0: 500 ms, 1: 600 ms, 2: 700 ms,
3: 800 ms, 4: 900 ms, 5: 1000 ms,
6: 1100 ms, 7: 1200 ms, 8: 1300 ms,...

2-32 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Error Troubleshooting
Call Progress 
To n e
Freq. FilterCall Progress Tone Freq. 
Filter0: 340Hz ~ 560Hz
1: 310Hz ~ 485Hz
2: 363Hz ~ 502Hz
3: 276Hz ~ 504Hz
4: 415Hz ~ 460Hz
5: 310Hz ~ 640Hz
6: 370Hz ~ 525Hz
RX PowerRx Call Detection Level 0: -36dB, 1: -37dB, 2: -38dB, 3: -39dB,
4: -40dB, 5: -41dB, 6: -42dB, 7: -43dB,
8: -44dB, 9: -45dB, 10: -46dB,
11: -47dB, 12: -48 dB
TX PowerTx Cable Equalizer 0: 0dB, 1: 2dB, 2: 4dB, 3: 6dB, 4:...

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-33Error Troubleshooting
Service Diagnostic Test Procedures
Phaser 3010/3040 Sensor Test Procedures 
The CE Diagnostic software extends the functionality of the Printer Settings Utility 
by adding a Service Diagnostics selection. CE Dagnostics provide a way to test 
electromechanical components, display printer status, and provide NVRAM access. 
When a PC is available, use CE Dagnostic software tests to diagnose problems and 
isolate which...

2-34 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Error Troubleshooting
Exit Sensor
1. Enter CE Diagnostics (page A-2).
2. Run the Exit Sensor test in the Digital Input drop down box.
3. Operate the actuator to check sensor function.
4. Confirm the display indicates the sensor functions correctly.
5. Press the Cancel button to stop the test.
s6000-143
Exit Sensor  Actuator
Paper
Paper 

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 2-35Error Troubleshooting
Registration Sensor
1. Enter CE Diagnostics (page A-2).
2. Open the Rear Door.
3. Run the Registration Sensor test.
4. Operate the actuator to check sensor function.
5. Confirm the display indicates the sensor functions correctly.
6. Press the Cancel button to stop the test.
7. Close the Rear Door.
s3040-172
Registration Sensor  Actuator 

2-36 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Error Troubleshooting
Rear Door Interlock
1. Enter CE Diagnostics (page A-2).
2. Run the Interlock Switch test .
3. Open and close the Rear Door to actuate the switch.
4. Confirm the display indicates the sensor functions correctly.
5. Press the Cancel button to stop the test.
6. Close the Rear Door. 
s3040-173