Xerox WorkCentre 3045 Service Manual

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-81Service Parts Disassembly
Registration Sensor Actuator
PL2.3.9
1. Remove the Rear Door (page 4-53).
2. Press inward on the left side retainer to release the left side boss and remove 
the lower chute.
s3040-074 

4-82 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
3. Remove the Registration Sensor Actuator by releasing the left end from the 
chassis and
Replacement Note
Install the spring as shown below.
s3040-036
s3040-079 

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-83Service Parts Disassembly
Registration Sensor
PL2.3.10
1. Open the Rear Door.
2. Press inward on the left side retainer to release the left side boss and remove 
the lower chute.
3. Release the 3 hooks that secure the Registration Sensor to the chassis.
s3040-074 

4-84 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
4. Rotate the Registration Actuator and disconnect P/J230 to remove the sensor 
from the chassis.
s3040-138
P/J230 

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-85Service Parts Disassembly
Feed Solenoid
PL2.3.21
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front USB Board.
8. Disconnect P/J6501 from the WiFi Adaptor.
9. Remove the Top Cover (page 4-52).
10. Remove the Rear Cover...

4-86 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
WorkCentre 3045 Xerographics
Xerographics Assembly
This procedure removes the developer and xerographic housings as a single unit.
PL3.1.5
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Left Cover (page 4-64).
5. Remove the Right Cover (page 4-57).
6. Remove the Scanner (page 4-109).
7. Disconnect P/J7601 from the Front...

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-87Service Parts Disassembly
25. Remove the FFC cover.
26. Remove 2 screws (silver, tapping. 8mm) that secure the upper plate to the 
xerographics assembly.
s3040-040 

4-88 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
27. Remove the 3 screws (silver, tap, 8 mm), to remove the xerographics assembly 
from the printer.
Replacement Note
Inspect the Feed and Separator Roller assemblies. Replace if worn.
s3040-041 

Phaser 3010/3040/WorkCentre 3045 Service Xerox Internal Use Only 4-89Service Parts Disassembly
Toner Dispense Assembly
PL4.1.1
Caution
The Toner Cartridge CRUM reader harness is attached to the Toner Dispense 
Assembly.
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Toner Cartridge (page 4-5).
5. Remove the Right Cover (page 4-57).
6. Remove the Left Cover (page 4-64).
7. Remove the Scanner (page 4-109).
8. Disconnect...

4-90 Xerox  Internal  Use  Only Phaser 3010/3040/WorkCentre 3045 Service  Service Parts Disassembly
Toner Motor
PL4.1.2
Note
The Toner motor ground wire is not captive to the chassis.
1. Remove the Main Tray (page 4-58).
2. Remove the Front Cover (page 4-60).
3. Remove the Inner Front Cover (page 4-62).
4. Remove the Toner Cartridge (page 4-5).
5. Remove the Right Cover (page 4-57).
6. Remove the Left Cover (page 4-64).
7. Remove the Scanner (page 4-109).
8. Disconnect P/J7601 from the Front USB Board....