Xerox Workcentre 24 Pcl 6 Manual

1–89
USER GUIDE (COPIER)
Duplex Automatic Document Feeder (DADF) (Optional Accessory)
This section describes the Duplex Automatic Document Feeder 
(DADF) for the WorkCentre 24 printer/copier.
The DADF automatically feeds up to 50 sheets of the same size 
documents or mixed size documents, one at a time, onto the 
Document Glass, feeding the top sheet first. Documents are 
delivered to the Original Catch Tray after they have been copied.
NOTE: If the DADF belt is dirty and the original is a thin or...

1–90
USER GUIDE (COPIER)
Document Specifications
Always use the recommended types of input documents so that 
the Duplex Automatic Document Feeder operates within the 
design specifications. Documents jams may occur if non-standard 
documents are used, resulting in damaged documents.
Standard DADF document specifications
WeightThe document should be 16 lb. to 32 lb. (64 to 128 gsm)
SizeNorth and South America:
8.5x5.5 in., 8.5x11 in., 8.5x14 in., 11x17 in., A4
European market:
A5, A4, A3, 8.5x13 in.,...

1–91
USER GUIDE (COPIER)
Documents Not Recommended
The following document types cause document jams or 
malfunction of the printer/copier. Make copies of these documents 
by placing them directly onto the Document Glass.
• Book, pamphlet, and booklet documents
• Broken, creased, or paste-up documents
• Documents with clips and staples
• Transparent documents (the document size cannot be 
detected automatically, or the DADF belt is copied)
• Coated paper or carbon-backed documents
• Documents smaller than...

1–92
USER GUIDE (COPIER)
Loading Documents in the DADF
You can load up to 50 documents from 16 lb. to 32 lb. (64 to 128 
gsm) into the DADF.
1Remove any paper clips or staples from the documents. Align the 
documents.
2Place the documents face up in the Original Input Area of the 
DADF. Slide the documents to the left until the green Document 
Feed Lamp lights.
If the lamp does not light, readjust the alignment and or the 
placement of the documents until the lamp lights.
3Slide the document guide toward...

1–93
USER GUIDE (COPIER)
Finisher (Optional Accessory)
The WorkCentre 24 printer/copier may be equipped with an 
optional Finisher. The Finisher contains the following components:
Finisher Cover ButtonProvides access to the Finisher paper path.
Finisher TrayCompleted jobs are delivered to this tray.
Finisher Front DoorProvides access to the Stapler area.
Staple CartridgeLoad a new staple pack when needed.
Finisher StandSupports the Finisher and may be used for storage.
Finisher InterfaceDelivers the...

1–94
USER GUIDE (COPIER)
Stapling Options
Stapling options are selected from the UI or from your printer 
driver and depend on the paper selected. The table below shows 
the acceptable paper sizes and stapling options.
Copying
Paper 
OrientationPaper SizeOne LeftTwo LeftTw o  U pOne RightTwo Right
LEFB5, A4, 
8.5x11 in.
SEFA4, 8x10 in., 
8.5x11 in.,  
8.5x13 in., 
8.5x14 in.
SEFB4, A3, 11x17 
in. 

1–95
USER GUIDE (COPIER)
Printing
Paper 
OrientationPaper SizeOne LeftTwo LeftTw o  U pOne RightTwo Right
LEFB5, A4, 
8.5x11 in.
SEFA4, 8x10 in., 
8.5x11 in., 
8.5x13 in., 
8.5x14 in.
SEFB4, A3, 
11x17 in. 

1–96
USER GUIDE (COPIER)
Job Status
This section describes how to check currently copying, printing, 
queued, or completed jobs. It also describes how to change print 
schedules to cancel print jobs, or to change the print priority of 
queued jobs.
Checking Current Jobs
This section describes the procedure for checking currently 
copying, printing or queued jobs.
1Select the Job Status button on the Control Panel. The Job 
Status screen is displayed.
2Select Current and Pending Jobs. The Current and...

1–97
USER GUIDE (COPIER)
4Check the status of the selected job.
• To cancel a job select Stop. This cancels processing of the 
currently printing, copying, or queued job.
• You can change the print priority when there are two or more 
queued jobs. To change the print priority:  
•Select Promote Job. The print order will be changed so 
that the job you instructed higher print priority to will be 
printed after the current job. 
NOTE: If you continue to change the print priority again after 
changing the...

1–98
USER GUIDE (COPIER)
Checking Completed Jobs
This section describes how to check completed jobs. A list 
displays whether jobs have been completed normally or not. This 
list also allows you to check details of completed jobs in more 
detail.
1Select the Job Status button on the Control Panel. The Job 
Status screen is displayed.
2Select Completed Jobs. The Completed Jobs screen is 
displayed. A job list is displayed if there are completed jobs.
3Select the job you want to check using the up and down...