Xerox Phaser 6130 User Manual

							Print-Quality Problems
Phaser® 6130 Printer
6-5
Partial blanks, creased 
paper, or blotted 
printingThe paper is damp.
Replace the paper.
The paper is outside the recommended specification range.
Replace the paper with a recommended size and type. See About Paper 
on page 4-5.
The transfer unit, or fuser, is not installed correctly.
Reinstall the transfer unit and/or fuser.
The toner cartridges are not Xerox toner cartridges.
Verify that the toner cartridges (C/M/Y/K) meet specifications, and replace 
if necessary.
Condensation inside the printer causes partial blanks or creased paper.
Turn the printer on, and leave it on, for at least one hour to get rid of the 
condensation. If the problems still occurs, see the Xerox Support website, 
www.xerox.com/office/6130support
, for assistance.
Vertical blanks The laser is being blocked. 
Remove the imagine unit and clean all debris from the laser len(s) with a 
lint free cloth.
The transfer unit, or fuser, is old or damaged.
Check the condition of the transfer unit and fuser, and replace as 
necessary.
The toner cartridges are not Xerox toner cartridges.
■Check the condition of the toner cartridge, and replace as necessary.
Verify that the toner cartridges (C/M/Y/K) meet specifications, and replace 
if necessary.
Slanted printing The paper guides in the manual feed slot or paper tray are not set 
correctly.
Reset the paper guides in the manual feed slot or paper tray. See Loading 
Paper on page 4-8.
Horizontal bands, 
approximately 21 mm 
wide, appear vertically 
every 75 mmThe imaging unit has been exposed to too much light; possibly from 
leaving the front door open too long. 
Replace the imaging unit.
Colors are blurry or 
there is white area 
around objectsColor to color alignment is not correct.
Use the automatic color registration. See Color Registration on page 6-6. Symptom Reason/Action
Downloaded From ManualsPrinter.com Manuals 
						

							Color Registration
Phaser® 6130 Printer
6-6
Color Registration
Color registration can be adjusted by the printer automatically, or you can manually adjust it. 
Color registration should be adjusted any time the printer is moved.
Automatic Color Registration Adjustment
Use the following procedure to perform automatic color registration adjustment.
1.Press the Menu button to display the 
Menu screen.
2.Press the Up Arrow or Down Arrow button until 
Admin Menu is displayed, and then 
press the Forward Arrow or OK button.
3.Press the Up Arrow or Down Arrow button until 
Maintenance Mode is displayed, and 
then press the Forward Arrow or OK button.
4.Press the Up Arrow or Down Arrow button until 
Adjust ColorRegi is displayed, and 
then press the Forward Arrow or OK button.
5.Press the Up Arrow or Down Arrow button until 
Auto Adjust is displayed, and then 
press the Forward Arrow or OK button.
6.Press the OK button when 
Are you sure? is displayed.
The adjustment is complete when 
Ready is displayed on the control panel.
Manual Color Registration Adjustment
You can fine tune color registration by performing a manual adjustment of color registration.
Printing the Color Registration Correction Chart
1.Press the Menu button to display the Menu screen.
2.Press the Up Arrow or Down Arrow button until 
Admin Menu is displayed, and then 
press the Forward Arrow or OK button.
3.Press the Up Arrow or Down Arrow button until 
Maintenance Mode is displayed, and 
then press the Forward Arrow or OK button.
4.Press the Up Arrow or Down Arrow button until 
Adjust ColorRegi is displayed, and 
then press the Forward Arrow or OK button.
5.Press the Up Arrow or Down Arrow button until 
Color Regi Chart is displayed, then 
press the OK button. The Color Registration Correction Chart is printed. When printing is 
finished, the print screen is displayed again.
Downloaded From ManualsPrinter.com Manuals 
						

							Color Registration
Phaser® 6130 Printer
6-7
Determining Values
From the lines to the right of the Y (yellow), M (magenta), and C (cyan) pattern, find the 
values of the straightest lines.
When “0” is the value nearest the straightest line, you do not need to adjust the color 
registration. When the value is not “0”, follow the procedure outlined in “Entering Values”.
Note: You can also use the densest colors of the grid to find the straightest lines. The colors 
printed at the highest density are those next to the straightest lines.
Entering Values
Using the control panel, enter the values that you found in the Color Registration Correction 
Chart to make adjustments.
1.Press the Menu button to display the 
Menu screen.
2.Press the Up Arrow or Down Arrow button until 
Admin Menu is displayed, then press 
the Forward Arrow or OK button.
3.Press the Up Arrow or Down Arrow button until 
Maintenance Mode is displayed, then 
press the Forward Arrow or OK button.
4.Press the Up Arrow or Down Arrow button until 
Adjust ColorRegi is displayed, then 
press the Forward Arrow or OK button.
5.Press the Up Arrow or Down Arrow button until 
Enter Number is displayed, then press 
the Forward Arrow or OK button.
6.Press the Up Arrow or Down Arrow button until you reach the value displayed on the 
chart.
7.Press the Forward Arrow button once and move the cursor to the next value.
8.Repeat steps 6 and 7 to continue adjusting the color registration.
9.Press the OK button twice. The Color Registration Correction Chart is printed with the 
new values. When printing is finished, the print screen is displayed again.
10.Color registration adjustment is complete when the straightest Y (yellow), M (magenta), 
and C (cyan) lines are next to the “0” line.
If “0” is not next to the straightest lines, determine the values and adjust again.
Note: After printing the Color Registration Correction Chart, do not turn off the printer until 
the printer motor has stopped running.
Downloaded From ManualsPrinter.com Manuals 
						

							Color Registration
Phaser® 6130 Printer
6-8
Enabling/Disabling Automatic Color Registration
Use the following procedure to enable/disable automatic color registration when a new toner 
cartridge is installed.
1.Press the Menu button to display the 
Menu screen.
2.Press the Up Arrow or Down Arrow button until 
Admin Menu is displayed, and then 
press the Forward Arrow or OK button.
3.Press the Up Arrow or Down Arrow button until 
Maintenance Mode is displayed, and 
then press the Forward Arrow or OK button.
4.Press the Up Arrow or Down Arrow button until 
Auto Regi Adj is displayed, and then 
press the Forward Arrow or OK button.
5.Press the Up Arrow or Down Arrow button to turn automatic color registration 
On or Off.
Downloaded From ManualsPrinter.com Manuals 
						

							Phaser® 6130 Printer
7-1 This chapter includes:
 ■Paper Jams on page 7-2
■Problems With the Printer on page 7-8
■Control Panel Error Messages on page 7-12
■Getting Help on page 7-16
See also: 
Troubleshooting video tutorials at www.xerox.com/office/6130support
Print-Quality Problems on page 6-2
Troubleshooting
Downloaded From ManualsPrinter.com Manuals 
						

							Paper Jams
Phaser® 6130 Printer
7-2
Paper Jams
This section includes:
■Preventing and Clearing Paper Jams on page 7-2
■Paper Jams in the Paper Tray on page 7-3
■Paper Jams at the Fuser on page 7-6
See also: 
User Safety on page 1-2
Preventing and Clearing Paper Jams
To reduce the occurrence of paper jams, follow the guidelines and instructions in Printing 
Basics on page 4-1. It includes information about supported paper and media, guides for 
usage, and instructions for properly loading paper in the trays.
Caution: When removing jammed paper, make sure that no pieces of torn paper are left in the 
printer. If a sheet of paper is wrapped around the heat roller, or when clearing a jammed paper 
that is difficult or impossible to see, do not try to remove it by yourself. Turn off the printer 
immediately, and refer to the Xerox Support website, 
www.xerox.com/office/6130support.
Warning: The fuser and the surrounding area are hot and can cause burns.
Downloaded From ManualsPrinter.com Manuals 
						

							Paper Jams
Phaser® 6130 Printer
7-3
Paper Jams in the Paper Tray
Follow this procedure to remove paper jammed in the tray.
1.Pull the jammed paper out of the paper tray, and remove any remaining paper from the 
tray.
2.Close the paper tray.
3.Push the button and open the front cover.
Warning: Some components inside the printer, such as the fuser and surrounding area, 
are hot and can cause burns.
6130-028
6130-015
Downloaded From ManualsPrinter.com Manuals 
						

							Paper Jams
Phaser® 6130 Printer
7-4 4.Carefully remove any jammed paper in the printer. Confirm that there are no scraps of 
paper left inside.
Caution: Prolonged exposure to light may damage the imaging unit.
5.Close the front cover.
6130-098
6130-032
Downloaded From ManualsPrinter.com Manuals 
						

							Paper Jams
Phaser® 6130 Printer
7-5 6.Remove the tray from the printer, and then carefully pull out any jammed paper remaining 
inside the printer.
7.Insert the tray into the printer and push until it stops.
Caution: Do not use excessive force on the tray. Doing so could damage the tray or the inside 
of the printer.
6130-043
6130-027
Downloaded From ManualsPrinter.com Manuals 
						

							Paper Jams
Phaser® 6130 Printer
7-6
Paper Jams at the Fuser
1.Press the button and open the front cover.
2.Lift the levers at both ends of the fuser and remove the jammed paper. If the paper is torn, 
remove any scraps of paper remaining inside the printer.
Warning: Some components inside the printer, such as the fuser and surrounding area, 
are hot and can cause burns.
Caution: Prolonged exposure to light may damage the imaging unit.
6130-015
6130-046
Downloaded From ManualsPrinter.com Manuals