Xerox Phaser 3600DN User Manual

2.6   
Collation
This item allows you to collate the received data 
through the print driver. The printer will print 
output in sets to match the sequence of the 
originals.
•Off: When the printer receives data from the 
PC driver, it will print out as received.
•On: When the printer receives data from PC 
driver, it will print out after storing and 
collating the data.
SmartDuplexing
If this menu is set to 
On, the printer will detect a 
single page job and print it as a simplex-single-
page even though...

2.7   
Emulation menu
Use the Emulation menu to configure printer language emulation. Secure Print
•Release All: If this menu is configured to Off, 
Release item in Secure Print menu launches 
only one file which agrees with the user name 
and the passcode for the file. 
If this menu is configured to On, Release 
item in Secure Print menu releases every file 
that matches the user name and the 
passcode.
The default is Off.
•Delete: You can delete all of the pages 
regardless of the user name or the...

2.8   
PostScript
This menu provides you with the Print PS Error menu item. 
EPSON
This menu sets the EPSON emulation configuration.Lines
This item allows you to set vertical spacing from 5 to 
128 lines for the default paper size. The lines may 
differ according to the paper size and printing 
orientation. 
ItemExplanation
Print PS 
Error
You can select whether or not your printer prints an 
error list when a PS error occurs.
•Select On to print PS 3 emulation errors. If an error 
occurs, the job stops...

2.9   
Ethernet 
Speed
This item allows you to select the ethernet speed.
Clear 
SettingThis item performs a simple reset and restores the 
factory default settings for the network 
configuration. This setting will only take effect after 
you have reset the printer.
Network 
Info.This item prints a page showing the network 
parameters you set. 
802.1x
This item is for connecting with an authentication 
server. If you need to connect this product to an 
authentication server, set this item On, and select...

3.1   
3 Software overview
This chapter gives you an overview of the software that comes with your 
printer. Further details about installing and using the software are 
explained in the Software Section.
This chapter includes:
• Supplied software
• Printer driver features
• System requirements
Supplied software
You must install the printer software using the supplied CD after you 
have set up your printer and connected it to your computer. 
CD provides you with the following software:
CDContents
Printer...

3.2   
Printer driver features
Your printer drivers support the following standard features:
• Paper source selection
• Paper size, orientation and media type
• Number of copies
In addition, you can use various special printing features. The following 
table shows a general overview of features supported by your printer 
drivers: 
FeatureWindowsMac OS
PCL 6 PostScriptPostScript
Print quality option O O O
Poster printing O
XX
Multiple pages per sheet 
(N-up)OO O
Fit to page printing O O O
Scale printing O...

4.1   
4 Network setup (Phaser 3600/N, 
Phaser 3600/DN only)
This chapter gives you step-by-step instructions for setting up your 
printer for network connections.
This chapter includes:
• Introduction
• Supported operating systems
• Configuring TCP/IP
• Configuring EtherTalk
• Configuring IPX frame types
• Setting Ethernet speed
• Restoring the network configuration
• Printing a network configuration page
• Configuring 802.1x
• Configuring Port 9100
• Configuring LPR
• Configuring IPP
• Configuring SLP...

4.2   
Configuring TCP/IP
Your printer can be set up with a variety of TCP/IP network information, 
such as an IP address, a subnet mask, a gateway, and DNS addresses. 
There are several ways in which your printer can be assigned a TCP/IP 
address, depending on your network.
• Static addressing: A TCP/IP address is assigned manually by the 
system administrator.
• Dynamic addressing via BOOTP/DHCP (default): A TCP/IP address 
is assigned automatically by the server.
Note 
Before configuring TCP/IP, you...

4.3   
Setting Ethernet speed
You can select the communication speed for Ethernet connections.
1Press Menu until Network appears on the bottom line of the 
display and press OK.
2Press the Up/down arrow buttons until Ethernet Speed appears 
and press OK.
3Press the Up/down arrow buttons until the speed you want 
appears and press OK.
4Press Start/Stop to return to Standby mode.
Restoring the network configuration
You can return the network configuration to its default settings.
1Press Menu until Network...

4.4   
Configuring LPR
Your printer can use LPR (Line Printer Protocol) which transmit the 
printing data through port 510. To enable LPR, take the following steps:
1Press Menu until Network appears on the bottom line of the 
display and press OK.
2Press the Up/down arrow buttons until LPR appears and press 
OK.
3Press the Up/down arrow buttons until On appears and press OK.
Configuring IPP
Your printer can use IPP ( Internet Printing Protocol) which transmit the 
printing data through port 631. To...