Xerox 7142 User Manual

Changing the Default Time Settings 
Xerox WorkCentre 7132 User Guide 41
is pressed, or a fax or print job is received by the machine. The factory default setting 
of 60 minutes is customer changeable within the range of 1 to 240 minutes, and must 
be longer than the Low Power Mode time value. The time specified for entering the 
Sleep Mode will be counted from when the machine enters the Low Power Mode.
For more information, refer to Auto Power Saver in the Setups chapter on page 222.
Changing the...

2 Product Overview 
42 Xerox WorkCentre 7132 User Guide
5.Select [Common Settings] on 
the [System Settings] screen.
6.Select [Machine Clock/Timers] 
on the [Common Settings] 
screen.
7.Select the required option.
8.Select [Change Settings].
9.Change the required setting. 
Use the scroll bars to switch 
between screens.
10.Select [Save].
Modes
Use the buttons to access the screens which allow you to select features, monitor the 
status of jobs and obtain general information on the machine.
There are...

Job Interrupt 
Xerox WorkCentre 7132 User Guide 43
All Services
Use this button to access all the services available on the machine.
NOTE:  The arrangement of service icons displayed on the screen can be changed by 
the Key Operator.
1.Press the  button 
on the control panel.
Features
Use this button to go back one previous screen. If you are using the [Job Status] screen 
or [Machine Status] screen, press the  button to return to the previous copy, 
fax, and scan feature screen. The copy, fax, or scan...

2 Product Overview 
44 Xerox WorkCentre 7132 User Guide
1.Press the  button on 
the control panel.
2.Enter the commands for the new 
job you require.
3.Press the  button on the 
control panel.
4.To restart the interrupted job, 
press the  button 
again, and press the  
button.
NOTE:  Interrupted jobs cannot be promoted, released or deleted in the Print Queue.
Recycled Paper
The use of recycled paper in the machine benefits the environment with no degradation 
in performance. Xerox recommends recycled...

Xerox WorkCentre 7132 User Guide 45
3Copy
This chapter contains information on the copy screens and the features available.
NOTE:  Some of the features described in this  chapter are optional, and may not apply 
to your machine configuration.
Copying Procedure
This section describes the ba sic copy procedure. Before making copies on the 
machine, confirm what is to be copied and  the number of copies required. Follow the 
steps below.
1. Load the Documents – page 45
2. Select the Features – page 47
3....

3 Copy 
46 Xerox WorkCentre 7132 User Guide
Document Feeder
The document feeder can hold up to 50 sheets of plain paper (16-32 lb bond or 38-
128 g/m2). The document can be any size of 125-297 mm (4.9-11.7 inches) for width 
and 115-432 mm (4.5-17 inches) for length, and the standard sizes of A5-A3 (5.5 x 
8.5 to 11 x 17) SEF. Make sure the documents are in good condition, and remove all 
staples or paper clips before loading. The docum ent feeder senses standard sizes, or 
you can manually enter a size...

Copying Procedure 
Xerox WorkCentre 7132 User Guide 47
Document Glass
The document glass is used for a single page or bound document up to 297 mm (11.7 
inches) for width and up to 432 mm (17 inches) for length.
NOTE:  Before you place the document on the do cument glass, make sure that the 
touch screen is ready. If you place the document on the document glass before the 
touch screen is ready, the paper size may not be detected correctly.
1.Raise the document feeder or 
the document glass cover....

3 Copy 
48 Xerox WorkCentre 7132 User Guide
NOTE: If the Authentication feature is enabled, you may be required to enter the user 
ID and password (if one is set up). If you need assistance, contact the Key Operator.
3.Select the button for the feature required. If [More] is selected, select [Save] to 
confirm the selected feature or [Cancel] to return to the previous screen.
If necessary, select one of the tabs, and c onfigure the copy settings. For information on 
the individual tabs, refer to the...

Copying Procedure 
Xerox WorkCentre 7132 User Guide 49
5. Confirm the Copy Job in the Job Status
1.Press the  button 
on the control panel to display 
the [Job Status] screen.
The queued copy job will be displayed. If no job is displayed on the touch screen, it may 
have already been processed.
For more information, refer to  Current and Pending Jobs in the Job Status chapter on 
page 306.
Stop the Copy Job
Follow the steps below to manually  cancel the activated copy job.
1.Select [Stop] on the touch...

3 Copy 
50 Xerox WorkCentre 7132 User Guide
Copy
This section describes the basic features for a copy job on the [Copy] screen. For 
information on the features avai lable, refer to the following.
Output Color – page 50
Reduce/Enlarge – page 51
Paper Supply – page 52
2 Sided Copying – page 53
Copy Output – page 54
1.Press the  button 
on the control panel.
2.Select [Copy] on the touch 
screen. Ensure that the [Copy] 
tab screen is displayed.
3.Select the required features.
Output Color
This feature...