Xerox 1632 2240 3535 Color Carrera Manual
Here you can view all the pages of manual Xerox 1632 2240 3535 Color Carrera Manual. The Xerox manuals for All in One Printer are available online for free. You can easily download all the documents as PDF.
Page 651
6/02 4-177 DC1632/2240 ADJ 9.12 Repairs and Adjustments Prelaunch Training/Review 4.Check vertical magnification (Figure 2): Measure the 300mm line running from near LE1 to the trail edge of the 1.8lp ladder. If the dimension is not 300mm ±1.5mm, perform the Adjustment. Figure 2 Checking Vertical Magnification Adjustment1.Horizontal Magnification Adjustment ï Enter dC131 [715-234] ï Each bit represents 0.1% change: Increase the value to lengthen the line Decrease the value to shorten the line 2....
Page 652
6/02 4-178DC1632/2240 ADJ 9.13 Prelaunch Training/Review Repairs and Adjustments ADJ 9.13 UI Display CalibrationPurposeAdjust the display by making the buttons on the display correspond to the Touch Panel, so that users can correctly select the content indicated on the display. Perform this adjustment when UI PWB or the Control Panel are replaced. AdjustmentNOTE: Use the touch pen for the adjustment as it is installed in the UI Control Panel of the machine. A tapered substitute can be replaced if the...
Page 653
6/02 4-179 DC1632/2240 ADJ 9.14 Repairs and Adjustments Prelaunch Training/Review ADJ 9.14 Inboard/Outboard DensityPurposeTo perform the ROS In/Out light quantity correction with this adjustment, when IN/Out densities are different but the parameters other than ROS light quantity judges that all is normal. Adjustment1. Enter dC612. 2. Select the Test Pattern in the modes as shown below and print out the test pattern. ï Pattern name: Binary highlight PG LUT: C-TRA On IOT ON (Pattern No 13??? 25?) ï Color...
Page 654
6/02 4-180DC1632/2240 ADJ 9.14 Prelaunch Training/Review Repairs and AdjustmentsFigure 2 Standard Pattern: Pattern 0 (Fig. 3)Figure 3 Group 1 (Fig. 4)
Page 655
6/02 4-181 DC1632/2240 ADJ 9.14 Repairs and Adjustments Prelaunch Training/ReviewFigure 4 Group 2 Group 3: when the patterns are dark/light for only both edges. (Fig. 5)
Page 656
6/02 4-182DC1632/2240 ADJ 9.14 Prelaunch Training/Review Repairs and AdjustmentsFigure 5 Group 3
Page 657
6/02 4-183 DC1632/2240 ADJ 9.14 Repairs and Adjustments Prelaunch Training/Review (Fig. 6) Figure 6 Group 4 (Fig. 7)Figure 7 Group 5 4. Select a pattern and change the following NVM corresponding to the pattern. NOTE: Do NOT use the value other than the recommended values below as the NVM value. The In/Out density adjustment is available by changing the 6 NVM below. Table 1 Chain/Link no. NVM names [753-801] Legible Adjustment (Yellow) [753-802] Legible Adjustment (Magenta) [753-803] Legible...
Page 658
6/02 4-184DC1632/2240 ADJ 9.14 Prelaunch Training/Review Repairs and AdjustmentsReference Information The correct light quantity value in ROS is normally 1024. If the value is decreased by 5%, the light quantity decreases too. Hence, entering the 5 stages of light quantity correction value by 5% is possible as below. 1024: Correct ROS Light Quantity Value 973: Light quantity value of 5% down 922: Light quantity value of 10% down 870: Light quantity value of 15% down 919: Light quantity value of 20%...
Page 659
6/02 4-185 DC1632/2240 ADJ 12.1 Repairs and Adjustments Prelaunch Training/Review ADJ 12.1 Finisher AlignmentPurposeAlign IOT copy output with entrance to Finisher H Transport. Adjustment WARNINGTo avoid personal injury or shock, do not perform repair or adjustment activities with the power switch on or electrical power applied to the machine. 1. Ensure H Transport is set correctly (Figure 1) and (Figure 2). Figure 1 H Transport Clearance Figure 2 H Transport Gate Clearance 5 mm max. 10 mmH Transport...