Xerox 1632 2240 3535 Color Carrera Manual

6/02
3-11 DC1632/2240
IQ9, IQ12Image Quality Prelaunch Training/ReviewCheck the components in the Registration Transport Assembly (PL 2.6) for wear,
slipping, damage, or contamination. Clean/replace as required 
The defect occurred on copies from all five paper trays. 
YN
Check the components in the Registration Transport Assembly (PL 2.6) for wear,
slipping, damage, or contamination. Clean/replace as required
Check the IOT Lead Edge/Side Edge Registration (ADJ 9.9) for that tray. 
 Check the feeder for...

6/02
3-12DC1632/2240
IQ13, IQ14
Prelaunch Training/Review Image Quality
IQ13 Unfused Copy RAPInitial ActionsReplace the paper in use with fresh, dry paper of the correct specification.
Ensure that the media being used matches the settings on the UI screen or print driver. Using
the next heavier setting may resolve the problem.
If the Key Operator/Administrator has configured certain trays for a specific type of media,
ensure that the specified media is actually loaded in those trays.ProcedureCheck the...

6/02
3-13 DC1632/2240
IQ15, IQ16Image Quality Prelaunch Training/Review
IQ15 Mottle RAPThis RAP troubleshoots the causes of output images showing image density that varies from
inboard to outboard edges, or randomly throughout the print.Initial Actionsï Replace the paper in use with fresh, dry paper of the correct specification. Ensure that the
loaded media matches the UI or print driver settings.
ï Determine if the Drum Cartridge or any of the Toner Cartridges are approaching end-of-
life. Replace if...

6/02
3-14DC1632/2240
IQ20
Prelaunch Training/Review Image Quality
IQ20 1st BTR Checkout RAPProcedureYN
TBD - refer to Figure 1.  

6/02
3-15 DC1632/2240
IQ20
Image Quality Prelaunch Training/ReviewFigure 1 IQ20 RAP Circuit diagram 

6/02
3-16DC1632/2240
IQ21
Prelaunch Training/Review Image Quality
IQ21 Developer Bias RAPProcedure
WARNINGHIGH VOLTAGE!
Exercise caution when performing the voltage checks in this procedure.
Enter dC140 [09-026]. Check the voltage at P/J 580 for the affected color(s). There should be
approximately 370 VAC and -540 VDC (+/- 10%) present. The voltages are within range.
YN
There is +24 VDC from J 501 pin 13 to J 501 pin 10 on the HVPS T5 PWB.
YN
There is +24 VDC from J 553 pin 2 to J 553 pin 4 on the I/F...

6/02
3-17 DC1632/2240
IQ21
Image Quality Prelaunch Training/ReviewFigure 1 IQ21 RAP Circuit Diagram 

6/02
3-18DC1632/2240
IQ22
Prelaunch Training/Review Image Quality
IQ22 2nd BTR Checkout RAPProcedureYN
TBD - refer to Figure 1.  

6/02
3-19 DC1632/2240
IQ22
Image Quality Prelaunch Training/ReviewFigure 1 IQ22 RAP Circuit Diagram 

6/02
3-20DC1632/2240
IQ23
Prelaunch Training/Review Image Quality
IQ23 BCR Checkout RAPProcedureThe problem is very high single-color background
YN
TBDGo to Flag 3. Check the wires associated with the problem color for an open circuit. If the wires
are OK., check the HV outputs at P 581 for open circuits or loose contacts. If the problem per-
sists, replace the Drum Cartridge for the affected color (see Machine Consumables in Section
6). 
If this does not resolve the problem, replace the HVPS T7 PWB (PL...