Vodavi Triad 1/2/3 System Programming Manual

9-8 Toll Restriction
Toll Restriction
Ente ri ng Toll  Tabl e
Pro g ram mi ng  S te ps
If the system is in the  programming mode,  continue using the program 
codes. If  starting to program  here, enter  the programming mode.
1. Press FLASH and  di al [70]. The  following message displays:
2 . To  pr ogra m All ow/De ny t abl es,  pr es s t he  ap prop ri at e Tab le  but t on 
and enter information as outlined in the following  procedures.
3. To  program Special Tables 1-3, it  is necessary to associate...

To ll  R e s t r ic t i o n 9 - 9
The buttons  on the  digital terminal  are defined as shown below  when 
entering the  Toll  Restriction programming area:
When the  system searches the  Allow and Deny tables,  the entries  are 
checked starting with  Bin  01 and proceeding sequentially through the 
ta bl e t o th e l ast  bi n. I n ad dit i on the  A ll ow T abl e i s a lway s se ar c hed  bef ore  
looking at the Deny Table. Therefore, the entry order is important. Entries 
tha t  ar e s pe ci fi c (e...

9-10 To l l  Res trictio n
All ow  Ta b le
Pro g ram mi ng  S te ps
1. Pr es s t he  ALLOW  TABLE  A or  ALLOW  TABLE  B f le xib le  but ton  
(FLASH 70, Bu tton  #1 o r #3). T he f oll owin g me ssa ge  is  shown  on 
the  d isp lay  te l epho n e:
The  fi rs t two  bi n l o c ati o ns di spl ay.
2. Enter a  valid  bin numb er (01–2 0)  of t he  bi n t o be  pr ogr amme d.
It is re comme nded  th at:
†B in 17  b e r es er ve d f o r an e ntr y th at re fe re nc es SP EC IA L TA B LE 1
†B in 18  b e r...

To ll  R e s t r ic t i o n 9 - 1 1
Des crip ti on
Each Allow T able con ta ins  20 b in numbe rs . E ach b in numbe r may be up 
to  8  digits,  including Do Not Care digits and Search Special Table 
commands. Entries into the Allow Table represent exceptions to numbers 
or  cod es  tha t a re to be allowed only if they  would  otherwis e be res tricted  
by an entry in the Deny Table.
Ex a m pl e
If [1 555 1212] is allowed but [1+] numbers are denied,  by  an entry  into 
the Deny Table, [1 555 1212]...

9-12 To l l  Res trictio n
Rule s f or  E nt ri es  t h at  R efe rence  Spe ci a l T a bl es
For  e ntr ie s  re fer e nc ing  the  fi r st  t hre e  spe c ia l t ab le s a  sp ec i fic   are a  c ode 
must  b e i de nti fi ed  (one  for  ea ch t abl e  nee de d). T he n mak e no te  as  t o 
how the  numbers are dialed when dialing numbers to this area  code  (i.e., 
with a  l ead ing  di git [1] or n o le adi ng  digi t [1] ).
The entry into the  Allow Table would  be  entered as follows:
†Lea ding...

To ll  R e s t r ic t i o n 9 - 1 3
2. When the  first two bin  locations are displayed, enter  the 2-digit  bin 
nu mber ( 01–10) of  the bin to be programmed.
3. Enter the  deny code:
[0–9] ,  [6], [#] = Corr esponding deny dig its numb ers
MUTE = Do No t Care digi t
4. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay n ow upda te s.
5. When all  entries for  one table are  complete,  press the flexible button 
for  the next table.
Er a si n g a Bin  Nu m be...

9-14 To l l  Res trictio n
Spe cial Table
Pro g ram mi ng  S te ps
To prog ram  a Spe cia l T abl e , i t is  fi rs t nece ssa ry to ass ign  an are a code to 
the table (except for the home area code).
1. Press the appropriate AREA  CODE TABLE (#1 to #3) flexible button 
(FLASH 70, Bu tton s #9 to #11). The following  message displays:
2. Enter a valid area code.
3. Press the HOLD button to save the entry. A confirmation tone is heard 
a nd t he  di spl ay u pdat es .
Entering  Office Codes in a Special...

To ll  R e s t r ic t i o n 9 - 1 5
Des crip ti on
The Special Tables  provide  greater flexibility in designing a  toll plan for  a 
par t icul ar  si te .
†Each  Specia l  Ta ble a llows entry of  up to 800 of fice codes ( 200–999).
†Three of  these tables must  be  assigned an area code by  which they 
are referenced. The fourth  table is  reserved  for  the home area code 
and re qui re s no are a co de ent r y.
†The  Sp ec i al  Tabl es  ar e  re fer enc e d t hr ough e ntr i es  in  th e a ll ow t...

9-16 To l l  Res trictio n
Disp lay Toll  Tabl e Entri es
Pro g ram mi ng  S te ps
Press the DISPLAY TABLES flexible button (FLA SH 70 , Bu tton #12) while 
entering information into  a table.
Viewing  Entries in an Allow or Deny Table
Two  entries at  a time are displayed o n the  bottom  line  of the  display.
1. Pres s the  DISPLAY TABLE S b utton a gain, the  next highe r  bins  displays.
2 . Whe n th e l ast  e ntr i es  are  di spl aye d, pr es s t he D IS PLAY  TA BLES  but to n 
again to show the...

10
Least Cost Routing
(LCR)
This c hapter provides the functional steps  nec essary to use  the  LCR
features with the ST A RPL US Tria d 1/2/3  System. To implement the
most ec onomic al  routes for an outside c all,  you must  first enter the
Programming Mode.