Vodavi Starplus Triad S Installation Programming Manual

Programming LCR TablesB-13
Chapter  - Least Cost Routing
EXAMPLE -- If a call is placed at 5:45 pm on a Monday, then according to the Daily Start Time 
Table (using default values) the entry for time period two of the weekly schedule is checked. 
Because it is Monday the entry for time period two on Monday is used and the result is that the 
Time Period Route List number two (again using default values) is used for all routes. Thus, the call 
is routed according to the entries in Time Period Two Route...

B-14Programming LCR Tables
Chapter  - Least Cost Routing
LCR Routing for Toll Information
Description
The LCR Routing for Toll Information feature adds provisions to the LCR call processing which 
allows common call routing for all toll information calls. 1-(XXX) 555-1212, (XXX) 555-1212, 
1-555-1212, and 555-1212 calls are intercepted and sent to a selected route in the Route List 
Table.
Numbers dialed are integrated and if it is determined to be a toll information call, either 
preceded with an area...

Programming LCR TablesB-15
Chapter  - Least Cost Routing
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … LCR Call Progress feature is enabled.
Default LCR Database
Description
In an effort to decrease installation and set up time usually associated with LCR, a default LCR 
database was incorporated.
The default LCR database provides basic routing for local and long distance dialing. Default 
entries have been made in the 3-Digit Table for local office codes (NNXs) and all area...

B-16Programming LCR Tables
Chapter  - Least Cost Routing
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press the FORCE LCR flexible button (Button #11). The following message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
Conditions
» Only one station at a...

Programming LCR TablesB-17
Chapter  - Least Cost Routing
2. Enter the range of fixed station numbers (100-131) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect...

B-18Programming LCR Tables
Chapter  - Least Cost Routing
Enable / Disable Least Cost Routing
Description
To use Least Cost Routing, it must be enabled. Before enabling LCR, refer to the Least Cost 
Routing programming tables.
After the tables are programmed, you may then enable LCR for the system. After system 
initialization, a default LCR database is loaded into the LCR section of memory.
Programming Steps
1. Press the LCR ENABLE flexible button (FLASH 05, Button #7).
2. Enter a 0 or 1 that corresponds...

Programming LCR TablesB-19
Chapter  - Least Cost Routing
Conditions
» The user must have LCR enabled to get the Call Cost Display.
Initialize LCR Tables
Description
The LCR Tables may be initialized to set all tables to their original, default values. The 
following tables are reset to their original default value after initialization of the LCR Tables:
Programming Steps
1. Press the LCR TABLES flexible button (FLASH 80, Button #7). The following message 
displays:
2. Press the HOLD button. A...

B-20Programming LCR Tables
Chapter  - Least Cost Routing
Print LCR Tables
Description
The Print LCR Tables command dumps the entire database as a permanent record which can 
serve as a hardcopy of the database. The system baud rate must match that of the printer or 
receiving device.
When printing information from the LCR Tables, the following data prints (examples follow 
programming steps):

Exception Table

Route List Table

Insert/Delete Table

Daily Time Table

Weekly Time Table

To ll  Ta b l e s...

Programming LCR TablesB-21
Chapter  - Least Cost Routing
LC R P ri n t ou t
EXCEPTION CODE TABLE
----------------------DIGIT INS/DEL TABLE
-----------------------
CODE ROUTE NO
----------------------TABLE DIGITS
----------------------
ROUTE LIST TABLE
----------------------0
1PRE
PREP
RT TIME COST CO GRP INS/DEL GRP PR 2 PRE P
01
2
3
4026
026
026
0261
1
1
10
0
0
01
1
1
13
4
5
6PRE
PRE
PRE
PREP
P
P
P
11
2
3
4000
000
000
0001
1
1
10
0
0
01
1
1
17
8
9
10PRE
PRE
PRE
PREP
P
P
P
21
2
3
4010
010
010
0101
1
1...

B-22Programming LCR Tables
Chapter  - Least Cost Routing
3 DIGIT TABLE
----------------------
CODE LEADING 1 NON-LEADING 1
RR PP 6 RR PP 6
---------------------------------
11 ## ## N 6 ## N
200 0 11 N 1 7 N
201 0 11 N 1 7 N
202 0 11 N 1 7 N
203 0 11 N 1 7 N
204 3 11 N 1 7 N
205 0 11 N 1 7 N
206 0 11 N 1 7 N
207 0 11 N 1 7 N
208 0 11 N 1 7 N
209 0 11 N 1 7 N
210 0 11 N 1 7 N
211 ## ## N 1 7 N
212 0 11 N 1 7 N
213 0 11 N 1 7 N
214 0 11 N 1 7 N
215 0 11 N 1 7 N
216 0 11 N 1 7 N
217 0 11 N 1 7 N
218 0 11 N...