Vodavi Starplus Dhs/dhs-e User Guide

44 Features
2. Press [FEAT ]
3. Dial [7] + [7]. At an Executive Telephone, the 
following display will be seen momentarily.
4. If no further action is taken, the display returns to 
idle status. At this time, the two lines are 
conferenced.
To rejoin the unsupervised conference:
1. At your station, press [FEAT ].
2. Dial [6] + [0]
Directory Dial 
Description
Enables station users to obtain a directory of station 
users and have the system dial the extension shown in 
the display. The DHS system provides...

Features 45
4. Press the soft key  to locate the most 
likely entry and volume keys to scroll the names, 
until you locate the one you were trying to find: 
Then press any soft key to dial, once the desired 
name is displayed.
To execute a speed dial number using directory dial:
1. If the destination is a speed dial number, the 
number stored in the speed dial bin will be 
displayed 
2. Press a soft key
3. Once an idle line is accessed, the number 
displayed is dialed.
Distinctive Ringing - Station...

46 Features
2. Dial [#] + [7]
3. Dial a ringing tone code (1-5).
Executive Telephones
1. Press [FEAT ]
2. Dial [#] + [7]. You will hear the current ringing 
tone. The display will show:
3. Press [chg]. You will hear the new ringing tone. 
The display will show:
Do Not Disturb (DND)
Description
DND allows you to temporarily block and discontinue 
ringing from incoming CO calls and intercom calls. 
You can activate DND while your telephone is idle or 
busy. Some stations with a higher COS may override a...

Features 47
2. Dial [4]. You will hear a confirmation tone on an 
Executive Telephone displays:
3. Repeat Steps 1 and 2 above to cancel DND. You 
will hear a confirmation tone on an Executive 
Telephone. The display the will show the 
following prior to returning to the idle display 
message:
Conditions
†May cause analog VM integration situations, such 
as recalling at main attendant instead of the 
intended voice mailbox.
DND Override
Description
If you have an Executive Telephone you may override 
a...

48 Features
The Override option is displayed only if your COS 
is higher than the Station 16 COS.
2. Press [override]. If Station 16 is idle, your display 
shows:
OR
3. If Station 16 is busy, your display shows:
OR
4. If Station 16 is busy with Call Wait enabled, your 
display shows:
Direct Station Selector (DSS) Console 
Description
One DSS console may be assigned to a station. Each 
DSS Console uses one digital station port. Up to 24 
DSS consoles may be installed on a system. Features 
are separated...

Features 49
2. Press [FEAT ]
3. Dial the system feature code.
4. Press [HOLD]
To program a BLF/DSS button:
1. Dial [1]
2. Dial the station number.
3. Press [HOLD]
To program a CO line button:
1. Dial [0]
2. Dial the CO line number or code for a CO line 
group. 
Table 5: CO Line Flex Button Codes.
3. Press [HOLD]
To erase the contents of a programmable feature 
button:
1. Press [FEAT ]
2. Dial [#] + [5]Table 5: CO Line Flex Button Codes
00 =Any Group 4 = CO Line 4
01 = CO Line Grp 1 5 = CO Line 5
02 = CO...

50 Features
3. Press the Programmable Feature Button.
4. Dial [0]
5. Press [HOLD]
Executive Telephones
To program DSS console buttons:
1. Press [FEAT ]
2. Dial [#] + [5]. The display shows:
3. Press a programmable feature button. The current 
contents of that button is displayed. 
4. Press [show]. The name of the current feature 
stored is displayed.
5. Press [chg]. The display shows the following 
(DHS): 
Or on the DHS-E:
Two feature button categories are available for 
feature button programming on the...

Features 51
To program a CO line button:
1. Press [DIR]: 
2. Dial the CO line number (700-717). 
3. Press [save]
To program a BLF/DSS button:
1. On the DHS, press [STA], then chg.
2. Dial the Station number.
3. Press [save]
OR
1. On the DHS-E, Press [DIR]. The display shows:
2. Dial the station number.
3. Press [save]
To program a system feature:
1. On the DHS, press soft key [feat], then [chg].
2. Dial the Feature code number.
3. Press [save]
OR
1. On the DHS-E, press soft key [feat]. The display...

52 Features
2. Press [FEAT ]. F will appear on the display:
3. Dial the feature code.
4. Press [save]
To erase the contents of a programmable feature 
button:
1. Press [save] instead of dialing a code.
Hold
Abandon (Loop Supervision)
Description
Each CO line has a programming option that directs 
the system to monitor distant party disconnect or 
False Hold conditions. 
Operation
1. While connected to any CO line:
2. Press [HOLD]
Conditions
†Certain COs do not provide loop supervision.
†Call abandon is...

Features 53
Automatic
Description
You may enable this feature on your telephone to 
simplify call handling, avoid accidental lost calls, and 
assist call transfers.
Operation
To enable/disable:
1. Press [FEAT ].
2. Dial [9] + [4].
During a telephone conversation: 
1. Press a different line button. The first call is 
automatically placed on Exclusive Hold.
Call Answer/Select
Description
Call Answer allows a user to place and retrieve calls ON 
and OFF of hold by simply pressing the HOLD button.
Operation...