Vivitek Projector DW3320 User Manual

							— 42 — 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp on page 58 to reset the lamp hour counter. 
 
Network 
 
ITEM DESCRIPTION 
Network State Displays the network connection status. 
DHCP 
Press ◄► to turn DHCP On or Off. 
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and 
DNS fields. 
IP Address  Enter a valid IP address if DHCP is turned off. 
Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. 
Gateway Enter a valid Gateway address if DHCP is turned off. 
DNS Enter a valid DNS name if DHCP is turned off. 
Apply Press  (Enter) / ► to confirm settings.   
						

							– 43 – 
LAN_RJ45 
 
Wired LAN Terminal functionalites 
Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. 
Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only collective 
projector management on a network but also management from a control panel on a PC (or Laptop) 
browser screen. 
 Crestron is a registered trademark of Crestron Electronics, Inc. of the United States. 
 Extron is a registered trademark of Extron Electronics, Inc. of the United States. 
 AMX is a registered trademark of AMX LLC of the United States. 
 PJLink applied for trademark and logo registration in Japan, the United States of America, and 
other countries by JBMIA. 
Supported External Devices 
This projector is supported by the specified commands of the Crestron Electronics controller and 
related software (ex, RoomView ® ). 
http://www.crestron.com/ 
This projector is supported by AMX ( Device Discovery ). 
http://www.amx.com/ 
This projector is compliant to support Extron device(s) for reference. 
http://www.extron.com/ 
This projector supports all commands of PJLink Class1 (Version 1.00). 
http://pjlink.jbmia.or.jp/english/ 
 
For more detail of information about the diverse types of external devices which can be connected to the 
LAN/RJ45 port and remote/control the projector, as well as the related control commands supporting for 
each external device, kindly please get contact with the Support-Service team directly.   
						

							— 44 — 
LAN_RJ45 
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 
 
2. On the PC (Laptop), select Start → Control Panel →Network and Internet. 
 
   
						

							– 45 – 
3. Right-click on Local Area Connection, and select Properties. 
 
4. In the Properties window, select the Networking tab, and select Internet Protocol (TCP/IP). 
5. Click Properties. 
 
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK. 
  
						

							— 46 — 
7. Press the Menu button on the projector. 
8. Select Settings2→ Advanced1 → Network 
9. After getting into Network, input the following: 
 DHCP: Off 
 IP Address: 10.10.10.10 
 Subnet Mask: 255.255.255.0 
 Gateway: 0.0.0.0 
 DNS Server: 0.0.0.0 
10. Press  (Enter) / ► to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher). 
 
11. In the Address bar, input the IP address: 10.10.10.10. 
12. Press  (Enter) / ►. 
The projector is setup for remote management. The LAN/RJ45 function displays as follows. 
    
						

							– 47 – 
 
 
CATEGORY ITEM INPUT-LENGTH 
Crestron Control 
IP Address 15 
IP ID 3 
Port 5 
Projector 
Projector Name 10 
Location 10 
Assigned To 10 
Network Configuration 
DHCP (Enabled) (N/A) 
IP Address 15 
Subnet Mask 15 
Default Gateway 15 
DNS Server 15 
User Password 
Enabled (N/A) 
New Password 10 
Confirm 10 
Admin Password 
Enabled (N/A) 
New Password 10 
Confirm 10 
For more information, please visit http://www.crestron.com.  
						

							— 48 — 
Preparing Email Alerts  
1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex-ample, 
Microsoft Internet Explorer v6.01/v8.0).  
2. From the Homepage of LAN/RJ45, click Alert Settings.  
 
3. By default, these input boxes in Alert Settings are blank.  
  
						

							– 49 – 
4. For Sending alert mail, input the following: 
SMTP field is the mail server for sending out email (SMTP protocol). This is a required field. 
To field is the recipient’s email address (for example, the projector administrator). This is a 
required field.  
Cc field sends a carbon copy of the alert to the specified email address. This is an optional field 
(for example, the projector administrator’s assistant).  
From field is the sender’s email address (for example, the projector administrator). This is a 
required field.  
 
 
Note: Fill in all fields as specified. User can click Send Test Mail to test what setting is correct. For 
successful sending an e-mail alert, you must select alert conditions and enter a correct e-mail address. 
 
  
						

							— 50 — 
RS232 by Telnet Function 
Besides projector connected to RS232 interface with “Hyper-Terminal” communication by dedicated 
RS232 command control, there is alternative RS232 command control way, so called “RS232 by TELNET” 
for LAN/RJ45 interface. 
Quick Start-Guide for “RS232 by TELNET” 
Check and get the IP-Address on OSD of the projector. 
Make sure that laptop/PC can access the web-page of the projector. 
Make sure that “Windows Firewall” setting to be disabled in case of “TELNET” function filtering out by 
laptop/PC. 
 
Start => All Programs => Accessories => Command Prompt 
  
						

							– 51 – 
Input the command format like the below: 
telnet  ttt.xxx.yyy.zzz  23 (“Enter” key pressed) 
(ttt.xxx.yyy.zzz: IP-Address of the projector) 
If Telnet-Connection ready, and user can have RS232 command input, then “Enter” key pressed, the 
RS232 command will be workable. 
 
How to have TELNET enabled in Windows VISTA / 7 
By default installation for Windows VISTA, “TELNET” function is not included. But end-user can have it 
by way of “Turn Windows features On or Off” to be enabled. 
Open “Control Panel” in Windows VISTA 
 
Open “Programs”