Vivitek Dw864 User Manual

— 12 — 
Setting  an  Access  Password  (Security  Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must  be entered after you power on the projector. (See Navigating the 
OSD on page 16 and Setting the OSD  Language on page 17 for help on using OSD  menus.) 
 Important: 
Keep the password in a safe place. W ithout the password, you will  not be able to use the projector. 
If you lose the password, contact your...

– 13 – 
5.  You  can use the cursor buttons 
▲▼◄► 
either  on keypad  or IR remote control 
for password entry.  You  can use any 
combination including  the  same arrow 
five  times, but  not less than  five. 
Press the cursor buttons in  any order 
to set the password. Push the MENU 
button to exit  the dialog  box. 
 
 
6.  The password confirm menu appears 
when user presses the power-on key 
in case the Security Lock is enabled.  
Enter the  password in the order  you 
set it at step 5. In  case you...

— 14 — 
Adjusting  the  Projector  Level 
Take note of the following  when setting up the projector: 
 The projector  table or  stand should be level and  sturdy. 
 Position the  projector so that  it is perpendicular  to the  screen. 
 Ensure the cables are in a  safe location.  You could trip  over them.  
 
To adjust the  angle  of the  picture, turn the  tilt-adjuster  right or left  until  the 
desired angle  has been  achieved. 
 
 
 
   

– 15 – 
Adjusting  the  Zoom,  Focus  and  Keystone 
1.  Use the Image-zoom  
control (on the  projector 
only)  to resize the 
projected image and 
screen size . 
 
2.  Use the Image-focus  
control (on the  projector 
only)  to sharpen the 
projected image . 
3.  Use the KEYST ONE 
buttons the  remote 
control to correct 
image-trapezoid (wider 
top or  bottom) effect. 
 
4.  The keystone  control  
appears on  the display.  
Adjusting  the  Volume 
1.  Press the Volume  +/-  
buttons on  the remote...

— 16 — 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD  Menu  Controls 
The projector has an OSD  that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons to navigate and make changes to the OSD.  
 
1. To enter the OSD,  press the 
M ENU button.  
2. There are five menus. Press 
the cursor ◄► button to 
move through the menus.  
3. Press the cursor ▲▼ button 
to move up and down  in a 
menu.  
4. Press ◄► to change values 
for...

– 17 – 
Setting  the OSD  Language 
Set the OSD  language to your preference before continuing. 
1. Press the MENU button. Press the cursor ◄► button to  navigate  to Installation  I. 
 
2. Press the cursor ▲▼ button  until Language is highlighted.  
 
3. Press the cursor ◄► button  until  the language  you  want is highlighted.  
4. Press the MENU button twice to close the  OSD.   
  

— 18 — 
OSD Menu  Overview 
Use  the following  illustration to quickly find a setting or determine the range for a setting. 
MAIN MENU 
 
SUB MENU 
   
SETTINGS 
Image  Display Mode    Presentation,  Bright,  Game, Movie, 
TV, sRGB, Blackboard,  User 
 Brilliant Color    0~10 
 Brightness    0~100 
 Contrast    0~100 
 Sharpness    0~31 
 Gamma    PC, MAC, Video,  Chart,  B&W 
 Advanced  Color  Space  Auto, RGB, YCbCr,  YPbPr 
  Color  Temperature  Cold,  Normal,  W arm 
  Color  Manager Red Hue,...

– 19 – 
 
MAIN MENU  SUB MENU    SETTINGS 
Installation  I  Language    English, Français,  Deutsch, 
Español,  Português, 簡体中文, 
繁體中文,  Italiano,  Norsk, 
Svenska,  Nederlands, Русский, 
Polski, Suomi, Ελληνικά, 한국어, 
Magyar,  Čeština, ةيبرعلا, Türkçe 
 Blank Screen    Black, Red,  Green,  Blue,  W hite 
 Projection    Front,  Rear,  Ceiling,  Rear  + 
Ceiling 
 Aspect Ratio    Fill, 4:3, 16:9,  Letter  Box, Native 
 Keystone    -40~40 
 Digital  Zoom    -10~10 
 Advanced  Security Lock  Off  ,On...

— 20 — 
 
MAIN MENU  SUB MENU    SETTINGS 
Installation  II  Auto Source    Off,  On 
 Auto Power  Off  (min.)    0~180 
 Auto Power  On    Off,  On 
 Fan  Speed    Normal,  High 
 Lamp  Mode    Std., Boost 
 Advanced  OSD  Menu  Setting Menu  Position Center,  Down,  Up, Left,  Right 
  Translucent  Menu 0%, 25%, 50%, 75%, 100% 
  Menu  Display 10~20 
  Peripheral  Test Remote Control  Test  
  Color  Test  
  Button Test  
  USB Test  
  Lamp  Hour  Reset   
  Low  Power  Mode  On, Off 
  3D 3D Off,...

– 21 – 
Image Menu  
Press the M ENU button to open the OSD menu. Press the cursor ◄► button to move to the Image 
Me nu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change 
values for settings. 
 
ITEM DESCRIPTION 
Display Mode Press the cursor  ◄► button to set the Display  Mode.  
Brilliant Color Press the cursor  ◄► button  to adjust the Brilliant  Color  valueK 
Brightness Press the cursor  ◄► button  to adjust the display brightnessK 
Contrast Press the cursor  ◄►...