Vivitek Dw864 User Manual

							— 12 — 
Setting  an  Access  Password  (Security  Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must  be entered after you power on the projector. (See Navigating the 
OSD on page 16 and Setting the OSD  Language on page 17 for help on using OSD  menus.) 
 Important: 
Keep the password in a safe place. W ithout the password, you will  not be able to use the projector. 
If you lose the password, contact your reseller for information on clearing the password. 
 
1.  Press the MENU button to  open the 
OSD menu. 
 
 
2.  Press the cursor ◄► button  to move 
to the Installation I menu, press the 
cursor ▲▼ button  to select 
Advanced. 
3.  Press the cursor ▲▼ button  to select  
Security Lock. 
 
4.  
Press the cursor ◄► button  to enable 
or disable  security lock  function. 
A  password dialog  box  automatically  
appears.   
						

							– 13 – 
5.  You  can use the cursor buttons 
▲▼◄► 
either  on keypad  or IR remote control 
for password entry.  You  can use any 
combination including  the  same arrow 
five  times, but  not less than  five. 
Press the cursor buttons in  any order 
to set the password. Push the MENU 
button to exit  the dialog  box. 
 
 
6.  The password confirm menu appears 
when user presses the power-on key 
in case the Security Lock is enabled.  
Enter the  password in the order  you 
set it at step 5. In  case you  forget the 
password, please contact the service 
center.  
The service center will validate  the 
owner and  help reset the  password.  
 
 
 
 
 
  
						

							— 14 — 
Adjusting  the  Projector  Level 
Take note of the following  when setting up the projector: 
 The projector  table or  stand should be level and  sturdy. 
 Position the  projector so that  it is perpendicular  to the  screen. 
 Ensure the cables are in a  safe location.  You could trip  over them.  
 
To adjust the  angle  of the  picture, turn the  tilt-adjuster  right or left  until  the 
desired angle  has been  achieved. 
 
 
 
   
						

							– 15 – 
Adjusting  the  Zoom,  Focus  and  Keystone 
1.  Use the Image-zoom  
control (on the  projector 
only)  to resize the 
projected image and 
screen size . 
 
2.  Use the Image-focus  
control (on the  projector 
only)  to sharpen the 
projected image . 
3.  Use the KEYST ONE 
buttons the  remote 
control to correct 
image-trapezoid (wider 
top or  bottom) effect. 
 
4.  The keystone  control  
appears on  the display.  
Adjusting  the  Volume 
1.  Press the Volume  +/-  
buttons on  the remote 
control.  
The volume  control  
appears on  the display. 
 
 
2.  Press the MUT E button 
to turn  off the  volume. 
       
						

							— 16 — 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD  Menu  Controls 
The projector has an OSD  that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons to navigate and make changes to the OSD.  
 
1. To enter the OSD,  press the 
M ENU button.  
2. There are five menus. Press 
the cursor ◄► button to 
move through the menus.  
3. Press the cursor ▲▼ button 
to move up and down  in a 
menu.  
4. Press ◄► to change values 
for settings. 
5. Press M ENU to close the 
OSD or leave a submenu. 
 
Note: 
Depending on the video  source, not all items in the OSD  are available. For example,  the 
Horizontal/Vertical Position items in the Computer menu can only be modified when connected 
to a PC. Items  that are not available  cannot be accessed and are grayed out.  
 2
112
3
4
5
6  
						

							– 17 – 
Setting  the OSD  Language 
Set the OSD  language to your preference before continuing. 
1. Press the MENU button. Press the cursor ◄► button to  navigate  to Installation  I. 
 
2. Press the cursor ▲▼ button  until Language is highlighted.  
 
3. Press the cursor ◄► button  until  the language  you  want is highlighted.  
4. Press the MENU button twice to close the  OSD.   
  
						

							— 18 — 
OSD Menu  Overview 
Use  the following  illustration to quickly find a setting or determine the range for a setting. 
MAIN MENU 
 
SUB MENU 
   
SETTINGS 
Image  Display Mode    Presentation,  Bright,  Game, Movie, 
TV, sRGB, Blackboard,  User 
 Brilliant Color    0~10 
 Brightness    0~100 
 Contrast    0~100 
 Sharpness    0~31 
 Gamma    PC, MAC, Video,  Chart,  B&W 
 Advanced  Color  Space  Auto, RGB, YCbCr,  YPbPr 
  Color  Temperature  Cold,  Normal,  W arm 
  Color  Manager Red Hue,  Saturation,  Gain 
  Green Hue,  Saturation,  Gain 
  Blue Hue,  Saturation,  Gain 
  Cyan Hue,  Saturation,  Gain 
  Magenta Hue,  Saturation,  Gain 
  Yellow Hue,  Saturation,  Gain 
  W hite Red,  Green,  Blue 
 Reset     
Computer  Horizontal  Position    -5~5 
 Vertical Position    -5~5 
 Frequency    0~31 
 Tracking    -5~5 
 Auto Image     
Video/Audio  Video  AGC    Off,  On 
 Video  Saturation    0~100 
 Video  Tint    0~100 
 Film Mode    Auto, Off 
 Video  Overscan    Off,  On 
 Closed  Captioning    Off,  On 
 Audio  Volume  0~8 
  Mute  Off,  On 
 Reset     
 
 
 
  
						

							– 19 – 
 
MAIN MENU  SUB MENU    SETTINGS 
Installation  I  Language    English, Français,  Deutsch, 
Español,  Português, 簡体中文, 
繁體中文,  Italiano,  Norsk, 
Svenska,  Nederlands, Русский, 
Polski, Suomi, Ελληνικά, 한국어, 
Magyar,  Čeština, ةيبرعلا, Türkçe 
 Blank Screen    Black, Red,  Green,  Blue,  W hite 
 Projection    Front,  Rear,  Ceiling,  Rear  + 
Ceiling 
 Aspect Ratio    Fill, 4:3, 16:9,  Letter  Box, Native 
 Keystone    -40~40 
 Digital  Zoom    -10~10 
 Advanced  Security Lock  Off  ,On 
 
 
 W all Color  Off,  Light  Yellow,  Pink, Light 
Green,  Blue,  Blackboard 
   Presentation  Timer Timer Off  ,On 
   Timer  Period 1-60 
   Timer  Reset  
   Projector  ID  0~98 
   Test  Pattern  None,  RGB  Ramps,  Color  Bars, 
Step Bars, Check  board,  Grid, 
Horizontal  Lines, Vertical Lines, 
Horizontal  Ramp,  Vertical 
Ramp,  W hile 
   Keypad  Lock  Off  ,On 
 Reset     
  
						

							— 20 — 
 
MAIN MENU  SUB MENU    SETTINGS 
Installation  II  Auto Source    Off,  On 
 Auto Power  Off  (min.)    0~180 
 Auto Power  On    Off,  On 
 Fan  Speed    Normal,  High 
 Lamp  Mode    Std., Boost 
 Advanced  OSD  Menu  Setting Menu  Position Center,  Down,  Up, Left,  Right 
  Translucent  Menu 0%, 25%, 50%, 75%, 100% 
  Menu  Display 10~20 
  Peripheral  Test Remote Control  Test  
  Color  Test  
  Button Test  
  USB Test  
  Lamp  Hour  Reset   
  Low  Power  Mode  On, Off 
  3D 3D Off,  DLP-Link,  nVidia 
  3D  Sync Invert On, Off 
  Network Network  State Disconnect, Connect 
  DHCP Off,  On 
  IP Address 0~255,  0~255,  0~255,  0~255 
  Subnet  Mask 0~255,  0~255,  0~255,  0~255 
  Gateway 0~255,  0~255,  0~255,  0~255 
  DNS 0~255,  0~255,  0~255,  0~255 
  Apply  
 Factory Reset     
 Status  Active  Source   
  Video  Information   
  Lamp  Hours  
(Std., Boost) 
  
  
						

							– 21 – 
Image Menu  
Press the M ENU button to open the OSD menu. Press the cursor ◄► button to move to the Image 
Me nu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change 
values for settings. 
 
ITEM DESCRIPTION 
Display Mode Press the cursor  ◄► button to set the Display  Mode.  
Brilliant Color Press the cursor  ◄► button  to adjust the Brilliant  Color  valueK 
Brightness Press the cursor  ◄► button  to adjust the display brightnessK 
Contrast Press the cursor  ◄► button  to adjust the display contrastK 
Sharpness Press the cursor  ◄► button  to adjust the display sharpness level. 
Gamm~ Press the cursor  ◄► button  to adjust the gamma  correction  of the  display.  
Advanced Press  (Enter)  / ► to enter  the  Advanced  menu. See Advanced  Feature on  page 
22. 
Reset Press  (Enter) / ► to reset  all settings to default  valuesK