ViewSonic Projector Pro8400 User Manual

							
ViewSonic  Pro8400 49
6. Network Display Management displays th e Device Management and pwPresenter 
Management information.
Device Management allows you to change device settings
.
i. Click to change display port allows you to select display location of screen. 
ii. Change password allows you to change password for the user type.
iii. Disconnect allows you to disconnect the projector from network.
iv. Access device via webpage allows you to access ViewSonic webpage con- trol system.
v. View device status displays device setting information and allows you to  enter conference control mode.
i
ii
iii
iv
v 
						

							
ViewSonic  Pro8400 50
pwPresenter Management allows you to select which computer to be connected 
and transfer the desktop content to the network projector.
7. Disconnect allows you to disconnect fr om the projector(s) by clicking the 
Disconnect icon.
Important
„Be sure to turn off other virtual network control programs before using 
pwPresenter. 
						

							
ViewSonic  Pro8400 51
Displaying pictures with a USB storage device
The built-in the ImageViewer application can display packaged images on a USB 
storage device (e.g. USB flash drive, and USB disk), a digital camera, or other device. 
You can connect a USB storage device to your projector.
1. Take a USB cable and connect the larger end to the USB A socket on the 
projector, and smaller end to the USB port of the device. If you are using a USB 
flash drive, connect it directly to the 
USB A socket.
2. The projector automatical ly display the thumbnails. Or your can manually select 
USB Reader from the source selection bar.
3. The ImageView main screen is displayed and ready to use. The main screen is 
displayed in Thumbnail Display Mode  which shows the following four parts:
i. Current path, USB storage device name and page number
ii. File and folder name display (i18N, multi-language)
iii. Thumbnail images (120 x 120 pixels images)
iv. Operation User Interface
4. Use the four directional buttons or page up/down button to move between pages/
folders. To Press and hold Menu and then press Enter to display the operation 
user interface. Use  /  to select the desi red item and adjust the settings with  
/ . To confirm the selection press Enter. The following buttons are supported 
in the user interface.
„Next: Display next page.
„Previous: Display previous page.
iv
i
iii
ii 
						

							
ViewSonic  Pro8400 52
„Thumbnail/Slide show/Display: Display thumbnails, start the slide show or 
display the selected image.
„Name Order/Extend Order/Size Order/Time Order: Select the order setting 
by file/folder name, extended file name, image size or time.
„EXIF ON/EXIF OFF: Display the Exif information of the image or not.
„File Name On/File Name Off: Display the file name or not.
The projector supports the following image formats:
„JPEG (JPG)
„Bitmap (BMP)
„Portable Network Graphic (PNG)
„Graphics Interchange Format (GIF)
„Tagged Image File Format (TIFF) 
						

							
ViewSonic  Pro8400 53
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt 
or spots will project on the screen and diminish image quality. If any other parts need 
replacing, contact your dealer or qualified service personnel. When cleaning any part 
of the projector, always switch off and unplug the projector first.
Warning
Never open any of the covers on the projector. Dangerous electrical voltages 
inside the projector can cause severe injury. Do not attempt to service this 
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth 
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Cleaning the Filter Cover
The filter cover, which is located at the side of the projector, should be cleaned after 
every 100 hours of use. If it is not cleaned periodically, it can become clogged with 
dust and prevent the projector from being ventilated properly. This can cause over 
heating and damage the projector.
To clean the filter cover:1. Switch the projector off and unplug the AC power cord from the wall socket.
2. Remove the filter cover as the illustration 
shown.
3. Clean the filter cover.
„To clean the filter cover, you are 
advised to use a small vacuum 
cleaner designed for computers and 
other office equipment.
„If the filter cover is torn, replace it.4. Replace the filter cover.
5. Attach the filter cover.  
6. Plug the power back into the projector.
„Turn off the projector and remove the AC power cord from the power outlet 
before beginning maintenance work.
„Make sure the lens is cool before cleaning.„Do not use detergents or chemicals other than those noted above. Do not use 
benzene or thinners.
„Do not use chemical sprays.„Use a soft cloth or lens paper only. 
						

							
ViewSonic  Pro8400 54
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually 
decreases and the lamp becomes more susceptible to breakage. We recommend 
replacing the lamp if a warning message is displayed. Do not attempt to replace the 
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp is extremely hot right after turning off the projector. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait for at least 
45 minutes for the lamp to cool down.
„Do not touch the lamp glass at any time. The lamp may explode due to 
improper handling, including the touching of the lamp glass.
„Lamp lifetime may differ from lamp to lamp and according to the environment 
of use. There is no guarantee of the same lifetime for each lamp. Some lamps 
may fail or terminate their lifetime in a shorter period of time than other similar 
lamps.
„A lamp may explode as a result of vibration, shock or degradation as a result of 
hours of use as its lifetime draws to an end. Risk of explosion may differ 
according to the environment or conditions in which the projector and lamp are 
being used.
„Wear protective gloves and eyeglasses when fixing or detaching the lamp.„Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least 
for 5 minutes to turn off the projector after powering on.
„Do not operate the lamp in proximity to paper, cloth, or other combustible 
material nor cover it with such materials.
„Do not operate the lamp in an atmosphere containing an inflammable 
substance, such as thinner.
„Thoroughly ventilate the area or the room when operating the lamp in an 
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, 
nausea, dizziness, and other symptoms.
„The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury 
inside the lamp will be exposed. Leave the area immediately if the lamp 
shatters while being operated and ventilate the area for at least 30 minutes in 
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to 
user’s health. 
						

							
ViewSonic  Pro8400 55
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the 
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try  reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Information” menu.
„Dispose the used lamp according to local regulations.„Ensure that screws are tightened properly. Screws not tightened fully may 
result in injury or accidents.
„Since the lamp is made of glass, do not drop the unit and do not scratch the 
glass.
„Do not reuse the old lamp. This could cause the lamp to explode.„Be sure to turn off the projector and unplug the AC power cord before 
replacing the lamp.
„Do not use the projector with the lamp cover removed. 
						

							
ViewSonic  Pro8400 56
Specifications
Display system Single 0.65 DLP panel
Resolution 1080p (1920 × 1080 pixels)
Zoom 1.5X
F/No. 2.41 - 2.97
Focal length 20.72 - 31mm
Screen size 30” - 300”
Lamp 280W
Input terminal D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input (3.5 
mm stereo mini jack) x 2, HDMI x 2, Component RCA jack x 1, 
RCA audio jack (L/R) x 1, 3.5 mm  Mic input x1, USB  A type x1 
(supports firmware update, USB flash drive display and wireless 
dongle for USB display), USB mini-B type x1 (supports USB 
display)
Output terminal D-Sub 15 pin x 1,  Audio si gnal output (3.5 mm stereo mini jack) x 
1
Control terminal RS-232 x 1, 12-Vdc trigger output x 1, RJ45 x 1
Speaker 10 watt x 2
Video compatibility NTSC, NTSC 4.43 PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency 31 - 100 KHz
50 - 120 Hz
Environment Operating: Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power requirement AC 100-240 V, 50 - 60 Hz, 3.8A
Power consumption 390 W
Dimension (W x D x H) 334.6 x 264.5 x 109.5 mm
Weight 3.63 kg (8 lb)
Note: Design and Specifications are subject to change without prior notice. 
						

							
ViewSonic  Pro8400 57
Dimensions
 334.6 mm (W) x 264.5 mm (D) x 109.5 mm (H)
Ceiling mount installation
264.5
109.5334.6
64.5
84.9
174 227
103
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)Unit: mm 
						

							
ViewSonic  Pro8400 58
Appendix
LED Indicator Messages
LED type Color Status Meaning
Power LED Blue Solid Lamp life end
Lamp LED Red Flash
Temp LED Red Flash
Power LED Blue Solid Standby mode when green mode is 
turned on.
Lamp LED Red Off
Temp LED Red Off
Power LED Blue Flash Standby mode when green mode is 
turned off.
Lamp LED Red Off
Temp LED Red Off
Power LED Blue Solid Powering up
Lamp LED Red Off
Temp LED Red Off
Power LED Blue Solid Normal operation
Lamp LED Red Off
Temp LED Red Off
Power LED Blue Flash Powering down
(The projector needs to cool for 35 
seconds after the power is turned off.)
Lamp LED Red Off
Temp LED Red Off
Power LED Blue Solid The projector system has some
 
problems with its fans, so the projector 
cannot start up.
Lamp LED Red Solid
Temp LED Red Flash
Power LED Blue Solid The lamp has reached its end of life and 
must be changed soon. The lamp will 
continue to opearate until it failes. 
Change the lamp. If the lamp is off, then 
the ballast will become malfuction.
Lamp LED Red Solid
Temp LED Red Off
Power LED Blue Solid Temperature is too high. The lamp will 
turn off.  The fan motor is cooling the 
lamp.
Lamp LED Red Flash
Temp LED Red Off
Power LED Blue Off The lamp ignition failied. If temperature 
is too high, the fans will cool the lamp.
Lamp LED Red Solid
Temp LED Red Solid
Power LED Blue Flash The projector needs to cool for 90 
seconds after the power is turned off. If 
you try to re-start the projector, it will 
shut down again.
Lamp LED Red Solid
Temp LED Red Off