ViewSonic Projector Pro8400 User Manual

							
ViewSonic  Pro8400 9
Rear View 
Connection ports
AC power socket
Kensington lock
Rear IR remote control sensor
Spe ak er
Ventilation holes (exhaust)
Bottom View
Ceiling mount holes (M4*8)Tilt-adjustment feet
Security bar
132465
1
2
23
4
5
56
3
2
1
1
22
3
„This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package.
„Contact your dealer for information to mount the projector on a ceiling. 
						

							
ViewSonic  Pro8400 10
Using the Product
Control Panel
Power (Power LED indicator)
Refer to “LED Indicator Messages”.
TEMP  (Temperature LED indicator)
Refer to “LED Indicator Messages”.
LAMP  (Lamp LED indicator)
Refer to “LED Indicator Messages”.
Keystone/Arrow keys ( /Up,  /Down)
Manually correct distorted images resulting from an angled projection.
Four directional buttons
Use four directional buttons to select items or make adjustments to your  selection.
ENTER
Enter to sub-menu and confirm the menu selection.
SOURCE
Display the source selection bar.
MENU/EXIT
Display or exit the on-screen display menus.
Power
Turn the projector on or off. Right/Panel key
Activate panel key lock.
1 3 
4 
6 
7 
5 
4 
2 
8
9 
10
1
2
3
4
5
6
7
8
9
10 
						

							
ViewSonic  Pro8400 11
Connection Ports
RS-232
When operating the projector via a computer, connect this to the controlling 
computers RS-232C port.
Monitor Out
Connect to a computer display, etc.
Component (Y Cb/Pb Cr/Pr)
Connect Y Cb/Pb Cr/Pr output from video equipment to this jack.
S-Video
Connect S-Video output from video equipment to this jack.
USB B
USB display supports computer connection via USB mini-B type to A type cable.
USB A
This connector supports firmware update, USB flash drive display and wireless 
dongle for USB display.
LAN
For LAN display/network control and web server.
HDMI 1
Connect HDMI output from video equipment to this jack.
HDMI 2
Connect HDMI output from video equipment to this jack.
DC 12V Out
12V DC out
MIC in
Microphone input jack.
58123467
161011121314151718
9
1
2
3
4
5
6
7
8
9
10
11 
						

							
ViewSonic  Pro8400 12
Audio Out
Connect to a speaker or other audio input equipment.
Audio 2
Connect an audio output from video equipment or computer to this jack.
Audio 1
Connect an audio output from video equipment or computer to this jack.
Audio 3 (L/R)
Connect an audio output from video equipment to this jack.
Video
Connect composite video output from video equipment to this jack.
Computer in 2
Connect image input signal (analog RGB or component) to this jack.
Computer in 1
Connect image input signal (analog RGB or component) to this jack.12
13
14
15
16
17
18 
						

							
ViewSonic  Pro8400 13
Remote Control
Power
Turn the projector on or off.
HDMI 1
Display HDMI 1 signal.
Video
Switch input source to Composite/
S-Video by sequence.
Up/Volume +,  Down/
Volume -
When the On-Screen Display 
(OSD) menu is not activated, 
adjust the projector’s sound level.
Left/Mute
When the On-Screen Display 
(OSD) menu is not activated, this 
button is used as mute function.
Menu
Display on-screen display menus.
User 1
Recall the customized settings  
based on the current available 
settings.
Function
User definable key for customized 
function.
Gamma
Change the gamma setting.
Pattern
Display embedded test pattern.
Color Mode
Change the image mode setting 
by sequence.
Blank
Cut off the screen temporarily. 
Press again to cancel the Blank 
Screen function.
Light
Enable backlight functions of the 
remote control’s buttons.
Compo
Display Component video (YPbPr/ 
YCbCr) signal. HDMI 2
Display HDMI 2 signal.
PC
Switch input source to Computer in 1/
Computer in 2 by sequence.
Enter
Confirmed selections.
Right/ Lock
When the On-Screen Display (OSD) 
menu is activated, the #4, #5, and #18 
keys are used as directional arrows to 
select the desired menu items and to 
make adjustments.
Activate panel key lock.
ESC
Leave current page or items or to close 
OSD.1
2
3
4
5
6
7
8
9
10
11
12
13
14
HDMI1 HDMI2 Compo
PC
Video
Swap
Default
3
4
4 6
5
7
8
10
12
9
11
13
14
15
17
18
19
20
21
22
23
24
25
16
15
16
17
18
19 
						

							
ViewSonic  Pro8400 14
User 2
Recall the customized settings  
based on the current available 
settings.
PIP/POP
Switch screen to PIP/POP by 
sequence.
Swap
Swap input source in PIP or POP 
image. Aspect
Select the display aspect ratio.
RGBCMY
Change indivial RGBCMY color (user 
color setting).
Default
Restore settings to factory default.20
21
22
23
24
25 
						

							
ViewSonic  Pro8400 15
Installing the Batteries
1. Open the battery cover in the 
direction shown.
2. Install batteries as indicated by the  diagram inside the compartment.
3. Close the battery cover into 
position.
Caution
„ Risk of explosion if battery is replaced by an incorrect type.
„  Dispose of used batteries according to the instructions.
„  
Make sure the plus and minus terminals are correctly aligned when loading a battery.
„Keep the batteries out of the reach of children. There is a danger of death by 
accidentally swallowing the batteries.
„Remove batteries from remote control when not using for extended periods.„Do not dispose of the used batteries along with household waste. Dispose of used 
batteries according to local regulations.
„Danger of explosion may happen if batteries are incorrectly replaced. Replce all 
the batteries with new ones.
„Batteries should not be in or near to fire or water, keep batteries in a dark, cool 
and dry place.
„If suspect battery leakage, wipe out the leakage and then replace new batteries.  
If the leakage adheres to your body or clothes, rinse well with water immediately. 
						

							
ViewSonic  Pro8400 16
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„Operating the projector from
the front
„Operating the projector from 
the rear
HDMI 1 HDMI
2 Compo
PC
Vid
eo
Swap
Defa ult
7m5m15
306m
8m
6m
HDMI 1 HDMI
2 Compo
PC
Vid
eo
Swap
Defa ult
15
306m
8m
6m
„Do not point the laser directly to the peoples eyes (especially small children). 
There is a danger of injury to the eyes.
„The remote control may not operate when there is sunlight or other strong
light such as a fluorescent lamp shining on the remote sensor.
„Operate the remote control from a position where the remote sensor is visible.„Do not drop the remote control or jolt it.„Keep the remote control out of locations with excessively high temperature or
humidity.
„Do not get water on the remote control or place wet objects on it.„Do not disassemble the remote control. 
						

							
ViewSonic  Pro8400 17
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Important„In the connections shown above, some cables may not be included with the 
projector (see  “Package Contents” on page 6 ). They are commercially 
available from electronics stores.
„The connection illustrations above are for reference only. The rear 
connecting jacks available on the projector vary with each projector model.
„For detailed connection methods, see pages  18-21.
VGA cable (D-Sub to D-Sub) S-Video cable
VGA to DVI-A cable Composite Video cable
USB cable (mini-B type to  A type) Audio cable
VGA (D-Sub) to HDTV (RCA) cable HDMI cable
Component Video cable Microphone 3.5 mini jack cable
Audio L/R cable USB flash drive
7123
4
9
12
10
19
8
769 11
5
or
17
28
39
410
511
612 
						

							
ViewSonic  Pro8400 18
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both  
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are  
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of  the computer.
2. Connect the other end of the VGA cable to the 
Computer in 1 or Computer in 2 
signal input socket on the projector.
Important
„Many notebooks do not turn on their external video ports when connected to 
a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the 
external display on/off. Locate a function key labeled CRT/LCD or a function 
key with a monitor symbol on the notebook. Press FN and the labeled 
function key simultaneously. Refer to your notebooks documentation to find 
your notebooks key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, 
you can connect the  Monitor Out signal output socket on the projector to an external 
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in  “Connecting a computer” on 
page 18 .
2. Take a suitable VGA cable (only one suppl ied) and connect one end of the cable 
to the
 D-Sub input socket of the video monitor.Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable 
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the Monitor Out socket on the projector.Important
„The  Monitor Out  output only works when  Computer in 1 or Computer in 2  
is made to the projector.