ViewSonic Projector Pro10 Series User Manual

10
Power Cord
Unpack and inspect the box contents to ensure all parts listed below are\
 in 
the box. If something is missing, please contact our customer service.
Documentation:
 yUser’s Manual (CD)
 yQuick Start Card
 yWarranty Card (China only)
Projector with lens cover
Package Overview
  
Due to different applications in each Country , some regions may have different accessories.
VGA Cable
Remote Control
AAAA
PatternVGABNCSync
StandbyHDMIDVISourceVi deoS-Vi deoBlankVol +
Vol...

11
Product Overview
1. Lens Ring
2.  Zoom Lens
3.  IR Receivers
4.  LED Indicators
5.  Lamp Door
Main Unit
3
2
3
6. Outlet Vent
7.  Kensington Lock
8.  Security Bar
9.  Power Switch
10.  Power Connector
(Front View)
(Rear View)
5
1
4
11
 
  Do not block projector in/out air vents and keep 30cm clearance around vents for air flow concern.
6
8
7
9
12
13
14
10
11. Connector Panel
12.  Inlet Vent & Filter
13.  Audio Vent
14.  Keypad Panel
Min.  
30cm Min.  
30cm
Min.  
30cm  

12
Control Panel
1.  / Power key & Power LED
2.  Menu key
3.  Enter key
4.  Exit key
5.  Shift key
6.  Sync key
7.  Focus key
8.  Zoom key
9.  Source key
10.  Information key
11.  Four directional select keys
Source
Sync
Shift
1198
4
10
2
657
31  

13
1. Composite Video Input Connector
2.  HDMI Connector
3.  DVI-D Connector
4.  BNC Connector
5.  Wired Remote Input Connector
6.  12V Trigger Relay Connector
7.  RJ45 Network Connector
8.  S-Video Input Connector
9.  VGA Input Connector
10.   VGA Output Connector
11.   Audio Input Connector
12.   Audio Output Connector
13.   RS232 Connector (9-pin DIN Type) 
Connection Ports
321645
79101113128  

14
Remote Control
Pattern
VGA
BNC
Sync
Standby
HDMI
DVI
Source
Video
S-Vi deo
Blank
Vol +
Vol -Exi tMute
MenuMemory
FocusShiftZoom
Lamp PWModeRGB Gai n
PIPBlendGeo
MyButtonAspectKeystone
RC IDReset
12 3
45 6
78 9
0
LENS
Powe r On
1. Power ON 
Power on the projector.
2.  Pattern  
Display a test pattern.
3.  VGA  
Switch to VGA source.
4.  BNC  
Switch to Component video 
source.
5.  Sync  
Synchronize projector with 
source.
6.  Blank  
Switch to a blank screen.
7.  Four Directional Select Keys   
Press...

15
18. HDMI 
Switch to HDMI source.
19.  S-Video  
Switch to S-Video source.
20.  DVI 
Switch to DVI source.
21.  Source 
Automatically scans for connected source.
22.  Enter 
Confirm your item selection.
23.  Mute  
Turn the projector audio off/on.
24.  Memory 
Save the current lens settings to the memory.
25.  Zoom  
Adjust the lens zoom function.
26.  Shift 
Adjust the lens shift up/down/left/right.
27.  RGB Gain 
Enter the color management setting page.
28.  Mode  
Select the display mode...

16
Installation
Installing the Projector Lens
 Lens Installing Procedure:
1.    Remove the lens ring cover by counter-clockwise rotation. 1
2.    Remove the lens cap by counter-clockwise rotation. 
2
3.    Pull the release bar  and push the lens into position. 
3
4.  Lens assembled by clockwise rotation. 
4
5.    Lens ring cover assembled by clockwise rotation. 
5
  Warning: Do not transport the projector with any lens installed.
12
3
4
5
 
  Before installing or replacing the lens, switch off the power...

17
1. 
RS232 Cable
2.  VGA Cable
3.  DVI-D Cable
4.  HDMI Cable
5.  12V DC Jack
Connecting to Computer/Notebook
6. Audio Cable
7.  RJ45 Cable
8.  VGA Cable
9.  Power Cord
 
  Due to the difference in applications for each country, some regions may have different accessories.
 
™ Plug for 12V DC jack  
Plug: ID Φ 1.7mm
OD Φ 4.0mm
R
Monitor
Computer / Notebook
Power socket
1
7
3
2
4
5
+12V Output
8
6
9
 
™ Plug for wired remote 
at projector side  
Power
Signal
GroundΦ 3.5mm  phone jack
 
™...

18
Connecting to Video Sources
1. Composite Video cable
2.  S-Video Cable
3.  BNC Cable4. HDMI Cable
5.  Audio Cable
6.  Power Cord
R
DVD player, Set-top box, 
HDTV receiver
S-Video output
DVD player Audio output
1
5
3
4
2
6
Power socket
DVD player
 
  Due to the difference in applications for each country, some regions may have different accessories.  

19
Powering On the Projector
1. Securely connect the power cord and signal cable. Power on the switch 1 and 
the Power LED flashes Blue.
2.  Turn on the lamp by pressing the  “ 
 ” button either on the control panel of the 
projector or on the remote control 
2. The Power LED will turn blue. 
The startup screen will display in approximately 10 seconds. The first time you 
use the projector, you will be asked to select the preferred language and power 
saving mode.
3.  Turn on and connect the source that...