ViewSonic Projector PJD6250L User Manual

							 50
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not 
turned on). To use these functions, be sure you have turned on the corresponding 
menus under SOURCE > Standby Settings, and the cable connections are correctly 
made. For the connection methods, see the Connection on page 14 chapter.
Active VGA out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER 
OUT sockets are correctly connected to devices. The projector outputs the signal 
received only from COMPUTER IN 1.
Active Audio out
Selecting On outputs an audio signal when the AUDIO IN 1 socket is correctly 
connected to a proper device.
LAN Control
Selecting On allows the projector to provide the network function when it is in standby 
mode. See Controlling the projector through a LAN environment on page 44 for 
details.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker. 
Be sure you have made a correct connection to the projector audio input/output jacks. 
See Connection on page 14 for more details.
Adjusting the audio mode
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Audio Mode menu.
2. Press  /  to select a preferred audio mode.
• If available, you can press Audio Mode on the remote control to select a preferred audio
mode.
Muting the sound
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Mute menu.
2. Press  /  to select On.
• If available, you can press   on the remote control to toggle the projector audio between on
and off.
Adjusting the sound level
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Audio Volume menu. 
						

							 51
2. Press  /  to select a desired sound level.
• If available, you can press   /   on the remote control to adjust the projector’s sound
level.
Adjusting the Audio In 2 setting
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Audio In 2 menu.
2. Press  /  to decide the audio input source for the AUDIO IN 2/MIC port. This 
will affect the connection method for different devices, and where the sound is 
from.
• When Audio is selected:
• The selected input signal determines which sound will be played by the projector speaker,
and which sound will be output from the projector when AUDIO OUT is connected. For
instance, if you select a D-Sub / Comp. 1 source, the projector can play the sound received
from AUDIO IN 1.
• When Microphone is selected:
Adjusting the microphone sound level
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Microphone Volume menu.
2. Press  /  to select a desired sound level.
• This function is only available when the SYSTEM SETTING: ADVANCED > Audio Settings >
Audio In 2 menu is set to Microphone.
Turning off the Power On/Off Ring Tone
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio 
Settings > Power On/Off Ring Tone menu.
2. Press /  to select Off.
• The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power On/Off Ring Tone.Device COMPUTER IN 1 COMPUTER IN 2 Video/S-Video
Audio input portAUDIO IN 1 AUDIO IN 2 AUDIO IN 2
The projector can play 
the sound from...AUDIO IN 1 AUDIO IN 2 AUDIO IN 2
Audio output portAUDIO OUT AUDIO OUT AUDIO OUT
Device COMPUTER IN 1 COMPUTER IN 2 Video/S-Video
The projector can play 
the sound from...MIC MIC MIC
Audio output portAUDIO OUT AUDIO OUT AUDIO OUT 
						

							 52
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt 
or spots will project on the screen and diminish image quality. If any other parts need 
replacing, contact your dealer or qualified service personnel. When cleaning any part 
of the projector, always switch off and unplug the projector first.
Warning
• Never open any of the covers on the projector. Dangerous electrical voltages inside the 
projector can cause severe injury. Do not attempt to service this product yourself. Refer 
all servicing to qualified service personnel.
Cleaning the lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the projector housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth 
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Note
• Turn off the projector and remove the AC power cord from the power outlet before 
beginning maintenance work.
• Make sure the lens is cool before cleaning.
• Do not use detergents or chemicals other than those noted above. Do not use benzene 
or thinners.
• Do not use chemical sprays.
• Use a soft cloth or lens paper only. 
						

							 53
Installing the dust filter (optional accessory)
Caution
• It is important to clean the dust filter every 100 hours after the dust filter is installed.
• Be sure to turn off the projector and unplug it from power source before installing or 
detaching the filter.
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to 
your personal safety when replacing the dust filter.
Installing the dust filter
1. Be sure to turn off the projector and unplug it from power source.
2. As the arrows shown to the right, fit the filter by 
aligning and inserting it into the projector slots. 
Make sure it clicks into place.
For first time installation:
3. Open the OSD menu and go to the SYSTEM 
SETTING: ADVANCED > Filter Settings menu. 
4. Press Enter and the Filter Settings page is 
displayed.
5. Highlight Filter Mode and select On. The filter timer starts counting and the 
projector will remind you to clean the filter when the filter is in use for over 100 
hours.
Caution
• Set Filter Mode to On only when using the projector after the dust filter (optional 
accessory) is properly attached. Failing to do so will result in a shorter lamp life.
Obtaining the filter hour information
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter 
Settings menu. 
2. Press Enter and the Filter Settings page is displayed.
3. You will see the Filter Hours information on the menu.
Cleaning the dust filter
1. Be sure to turn off the projector and unplug it from power source.
2. Press the latches on the dust filter and remove the filter from the projector.
3. Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away.
4. Re-install the dust filter. 
						

							 54
Resetting the filter timer
5. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter 
Settings menu. 
6. Press Enter and the Filter Settings page is displayed.
7. Highlight Reset Filter Hours and press Enter. A warning message is displayed 
asking if you want to reset the filter timer.
8. Highlight Reset and press Enter. The lamp timer will be reset to 0.
Caution
• Remember to use Filter Mode to Off in the SYSTEM SETTING: ADVANCED > Filter 
Settings menu when using the projector with the dust filter removed. Setting Filter Mode 
to Off does not reset the filter timer. The timer will continue counting the next time you 
fit the filter back on and set Filter Mode to On.
Installing the cable management cover (optional 
accessory)
1. Make sure that all the cables are properly connected to the projector.
2. Attach the cable management cover to the back of the projector.
3. Tighten the screws that secure the cable management cover. 
						

							 55
Replacing the lamp
As the projector operates over time, the brightness of the projector lamp gradually 
decreases and the lamp becomes more susceptible to breakage. We recommend 
replacing the lamp if a warning message is displayed. Do not attempt to replace the 
lamp yourself. Contact the qualified service personnel for replacement.
Note
• The lamp is extremely hot right after turning off the projector. If you touch the lamp, you 
may scald your finger. When you replace the lamp, wait for at least 45 minutes for the 
lamp to cool down.
• Do not touch the lamp glass at any time. The lamp may explode due to improper 
handling, including the touching of the lamp glass.
• Lamp lifetime may differ from lamp to lamp and according to the environment of use. 
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or 
terminate their lifetime in a shorter period of time than other similar lamps.
• A lamp may explode as a result of vibration, shock or degradation as a result of hours of 
use as its lifetime draws to an end. Risk of explosion may differ according to the 
environment or conditions in which the projector and lamp are being used.
• Wear protective gloves and eyeglasses when fixing or detaching the lamp.
• Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5 
minutes to turn off the projector after powering on.
• Do not operate the lamp in proximity to paper, cloth, or other combustible material nor 
cover it with such materials.
• Do not operate the lamp in an atmosphere containing an inflammable substance, such 
as thinner.
• Thoroughly ventilate the area or the room when operating the lamp in an oxygen 
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness, 
and other symptoms.
• The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the 
lamp will be exposed. Leave the area immediately if the lamp shatters while being 
operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of 
mercury fumes. Otherwise it could be harmful to user’s health. 
						

							 56
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it.
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover.1
5. Remove the cover.2
6. Loosen the screws from the lamp module.3
7. Raise the handle and pull out the lamp module slowly and carefully.4
8. Insert the new lamp module into the projector and tighten the screws.
9. Replace the lamp cover and tighten the screw.
10. Turn on the projector.  If the lamp does not turn on after the warm-up period, try 
reinstalling the lamp.
11. Reset the lamp hour. Refer to the “SYSTEM SETTING: ADVANCED > Lamp 
Settings > Reset Lamp Hours” menu.
Note
• Dispose the used lamp according to local regulations.
• Ensure that screws are tightened properly. Screws not tightened fully may result in 
injury or accidents.
• Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
• Do not reuse the old lamp. This could cause the lamp to explode.
• Be sure to turn off the projector and unplug the AC power cord before replacing the 
lamp.
• Do not use the projector with the lamp cover removed.
13
4
2 
						

							 57
Specifications
Model name PJD6250L PJD6252L PJD7325 PJD6550W PJD6552W PJD7525W
Dislay system Single 0.55 DLP panel Single 0.65 DLP panel
Resolution XGA (1024 x 768 pixels) WXGA (1280 x 800 pixels)
Zoom 1.1x 1.2x
F/No. 2.5 - 2.7 2.56
Focal length 22.08 - 24.28mm 20.99 - 25.61mm
Screen size 30” - 300”
Lamp 203W 220W 250W 203W 220W 250W
Input terminalD-Sub 15-pin x 2, HDMI x 1, S-Video x 1, Video x 1, Audio signal input (3.5 
mm stereo mini jack) x 1, Audio signal input/Microphone input x 1
Output terminalD-Sub 15 pin x 1, Audio signal output (3.5 mm stereo mini jack) x 1, USB type 
A port for power charging (5V/2A)
Control terminalRS-232 x 1, Mini-B USB x1 (supports firmware upgrade and remote mouse 
control), RJ45 x 1
Speaker 16 watt x 1
Video compatibilityNTSC, NTSC 4.43
PA L ,  PA L - N ,  PA L  M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency31 - 100 KHz
24 - 120 Hz
EnvironmentOperating:
Temperature: 0°C to 40°C
Humidity: 10%-90%
Storage:
Temperature: -20°C to 60°C
Humidity:10%-90%
Power requirement AC 100-240 V, 50 - 60 Hz, 5.2A
Power consumption265W 
(Max.) 275W 
(Max.) 315W 
(Max.) 265W 
(Max.) 275W 
(Max.) 315W 
(Max.) 
Dimension 
(W x D x H)362 x 231 x 109 mm
Weight 2. 7 kg (6.0 lb) without cable management cover
Note: Design and Specifications are subject to change without prior notice. 
						

							 58
Dimensions
 362 mm (W) x 231 mm (D) x 109 mm (H)
Ceiling mount installation
231362
109
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
65.89
113.54
60.01 
						

							 59
Appendix
LED indicator messages
LED TypeColorStatusMeaning
Power LED Blue Solid
Normal power of standby mode . Temp LED Red Off
Lamp LED Red Off
Power LED Blue Flash
Low power of standby mode.  Temp LED Red Off
Lamp LED Red Off
Power LED Blue Flash
Powering up Te m p LED Red Off
Lamp LED Red Off
Power LED Blue Solid
Normal operation Temp LED Red Off
Lamp LED Red Off
Power LED Blue Solid
Powering down Temp LED Red Off
Lamp LED Red Off
Power LED Blue Solid
If the projector system has some problems 
with its fans, the projector will shut down. Temp LED Red Flash
Lamp LED Red Flash
Power LED Blue Solid The lamp has reached its end of life and 
must be changed soon. The lamp will 
continue to operate until it fails. Change the 
lamp. If the lamp is off, then the ballast will 
become malfunction. Temp LED Red Off
Lamp LED Red Flash
Power LED Blue Flash 1. Temperature is too high. The lamp will 
turn off. The fan motor is cooling the lamp.
Or
2. The cooling process is not complete after 
the projector is shut down and re-started 
right away. Temp LED Red Flash
Lamp LED Red Off
Power LED Blue Flash
The lamp ignition failed. If temperature is 
too high, the fans will cool the lamp.  Temp LED Red Off
Lamp LED Red Solid
Power LED Blue Solid
Color wheel start fail Temp LED Red Solid
Lamp LED Red Solid