ViewSonic Projector PJD6250L User Manual

							PJD6250L/PJD6252L/PJD7325/
PJD6550W/PJD6552W/PJD7525W
DLP Projector
User Guide
Model No.
VS15912/VS15913/VS15991/VS15915/VS15916/VS15992
IMPORTANT:  Please read this User Guide to obtain important information on installing 
and using your product in a safe manner, as well as registering your product for future 
service.  Warranty information contained in this User Guide will describe your limited 
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com  in  English,  or  in  specific  languages  using  the  Regional  selection 
box in the upper right corner of our website. “Antes de operar su equ\
ipo lea cu 
idadosamente las instrucciones en este manual” 
						

							Thank you for choosing ViewSonic
With over 25 years as a world leading provider of visual solutions,  
ViewSonic is dedicated to exceeding the world’s expectations for 
technological evolution, innovation, and simplicity. At ViewSonic, we 
believe that our products have the potential to make a positive impact 
in the world, and we are confident that the ViewSonic product you have 
chosen will serve you well. 
Once again, thank you for choosing ViewSonic !  
						

							Compliance Information
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to \
the following 
two conditions: (1) this device may not cause harmful interference, an\
d (2) this 
device must accept any interference received, including interference tha\
t may cause 
undesired operation.
This equipment has been tested and found to comply with the limits for a\
 Class 
B digital device, pursuant to part 15 of the FCC Rules. These limits are\
 designed 
to provide reasonable protection against harmful interference in a resid\
ential 
installation. This equipment generates, uses, and can radiate radio freq\
uency 
energy, and if not installed and used in accordance with the instruction\
s, may cause 
harmful interference to radio communications. However, there is no guara\
ntee that 
interference will not occur in a particular installation. If this equipm\
ent does cause 
harmful interference to radio or television reception, which can be dete\
rmined 
by turning the equipment off and on, the user is encouraged to try to co\
rrect the 
interference by one or more of the following measures:•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to\
 which the 
receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
Warning:  You are cautioned that changes or modifications not expressly approved \
by the party responsible for compliance could void your authority to ope\
rate the 
equipment.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage 
Directive 2006/95/EC.
Following information is only for EU-member states: 
The mark is in compliance with the Waste Electrical and Electronic 
Equipment Directive 2012/19/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment 
including any spent or discarded batteries or accumulators as unsorted 
municipal waste, but use the return and collection systems available. 
If the batteries, accumulators and button cells included with this equip\
ment, 
display the chemical symbol Hg, Cd, or Pb, then it means that the batter\
y 
has a heavy metal content of more than 0.0005% Mercury or more than, 
0.002% Cadmium, or more than 0.004% Lead.  
						

							Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Direc\
tive 
2011/65/EU of the European Parliament and the Council on restriction of \
the use 
of certain hazardous substances in electrical and electronic equipment (\
RoHS2 
Directive) and is deemed to comply with the maximum concentration value\
s issued 
by the European Technical Adaptation Committee (TAC) as shown below:
Substance Proposed Maximum 
ConcentrationActual Concentration
Lead (Pb)0.1%< 0.1%
Mercury (Hg) 0.1%< 0.1%
Cadmium (Cd) 0.01%< 0.01%
Hexavalent Chromium (Cr
6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1%< 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1%< 0.1%
Certain components of products as stated above are exempted under the Annex III 
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent 
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length ( ＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length ( ＞1,500 mm): maximum 13 mg per lamp.
2.  Lead in glass of cathode ray tubes.
3.  Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
4.  Lead as an alloying element in aluminium containing up to 0.4% lead by w\
eight.
5.  Copper alloy containing up to 4% lead by weight.
6.  Lead in high melting temperature type solders (i.e. lead-based alloys c\
ontaining 
85% by weight or more lead).
7.  Electrical and electronic components containing lead in a glass or ceram\
ic other 
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or \
in a glass or 
ceramic matrix compound.
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India) This product com\
plies 
with the “India E-waste Rule 2011” and prohibits use of lead, merc\
ury, hexavalent 
chromium, polybrominated biphenyls or polybrominated diphenyl ethers in \
concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, exc\
ept for 
the exemptions set in Schedule 2 of the Rule.  
						

							Important Safety Instructions
1. Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this unit near water.
6.  Clean with a soft, dry cloth.
7.  Do not block any ventilation openings. Install the unit in accordance wi\
th the 
manufacturer’s instructions.
8.  Do not install near any heat sources such as radiators, heat registers, \
stoves,   
or other devices (including amplifiers) that produce heat.
9.  Do not defeat the safety purpose of the polarized or grounding-type plug\
. A   
polarized plug has two blades with one wider than the other. A grounding\
 type 
plug has two blades and a third grounding prong. The wide blade and the \
third 
prong are provided for your safety. If the provided plug does not fit in\
to your   
outlet, consult an electrician for replacement of the obsolete outlet.
10.  Protect the power cord from being walked on or pinched particularly at p\
lugs. 
Convenience receptacles and the point where they exit from the unit. Be \
sure 
that the power outlet is located near the unit so that it is easily acce\
ssible.
11.  Only use attachments/accessories specified by the manufacturer.
12.  Use only with the cart, stand, tripod, bracket, or table specified by th\
e 
manufacturer, or sold with the unit. When a cart is used, use caution 
when moving the cart/unit combination to avoid injury from tipping 
over.
13.  Unplug this unit when unused for long periods of time.
14.  Refer all servicing to qualified service personnel. Servicing is require\
d when the 
unit has been damaged in any way, such as: if the power-supply cord or p\
lug is 
damaged, if liquid is spilled onto or objects fall into the unit, if the\
 unit is exposed 
to rain or moisture, or if the unit does not operate normally or has bee\
n dropped.  
						

							Copyright Information
Copyright © ViewSonic Corporation, 2015. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Mi\
crosoft 
Corporation in the United States and other countries.
ViewSonic and the three birds logo are registered trademarks of ViewSoni\
c 
Corporation.
VESA is a registered trademark of the Video Electronics Standards Associ\
ation. 
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Ma\
chines 
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or e\
ditorial errors 
or omissions contained herein; nor for incidental or consequential damag\
es resulting 
from furnishing this material, or the performance or use of this product\
.
In the interest of continuing product improvement, ViewSonic Corporation\
 reserves 
the right to change product spec ifications without notice. Information in this 
document may change without notice.
No part of this document may be copied, reproduced, or transmitted by an\
y means, 
for any purpose without prior written permission from ViewSonic Corporat\
ion.  
						

							Product Registration
To fulfill possible future product needs, and to receive additional prod\
uct information 
as it becomes available, please visit your region section on ViewSonic’\
s website to 
register your product online.
The ViewSonic CD also provides an opportunity for you to print the produ\
ct 
registration form. Upon completion, please mail or fax to a respective V\
iewSonic 
office. To find your registration form, use the directory “:\CD\Reg\
istration”. 
Registering your product will best prepare you for future customer servi\
ce needs.
Please print this user guide and fill the information in the “For You\
r Records” section. 
For additional information, please see the “Customer Support” sect\
ion in this guide.
For Your Records
Product Name:PJD6250L/PJD6252L/PJD7325/PJD6550W/PJD6552W/
PJD7525W
ViewSonic DLP Projector
Model Number: VS15912/VS15913/VS15991/VS15915/VS15916/VS15992
Document 
Number: PJD6250L/PJD6252L/PJD7325/PJD6550W/PJD6552W/
PJD7525W_UG_ENG Rev. 1A 06-08-15
Serial Number:
 
Purchase Date:
 
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you \
and the 
environment. Please use care and dispose of in accordance with local, st\
ate or   
federal laws.
ViewSonic respects the environment and is committed to working and livin\
g green. 
Thank you for being part of Smarter, Greener Computing.
Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/\
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx  
						

							 i
FCC notice
This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in residential installation. 
This equipment generates, uses and can radiate radio frequency energy and if not 
installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, detectable by turning the 
equipment in question off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the distance between the equipment and the receiver
• Connect the equipment to an outlet on a different circuit than that which the receiver 
is connected to
• Or consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to following 
two conditions:
1. This device may not cause harmful interference, and 
2. This device must accept any interference that may cause undesired operation. 
						

							 ii
Safety instructions
Read all of these instructions before you operate your projector and save for future 
reference.
1. Read instructions
All the safety and operating instructions should be read before the appliance is 
operated.
2. Notes and warnings
All notes and warnings in the operating instructions should be adhered to.
3. Cleaning
Unplug the projector from the wall socket before cleaning. Use a damp cloth for 
cleaning the projector housing. Do not use liquid or aerosol cleaners.
4. Accessories
Do not place this product on an unstable cart, stand, or table. The product may fall, 
causing serious damage to the product.
Keep the plastic packing materials (from the projector, accessories and optional 
parts) out of the reach of children as these bags may result in death by suffocation. 
Be particularly careful around the small children.
5. Ventilation
The projector is equipped with ventilation holes (intake) and ventilation holes 
(exhaust).
Do not block or place anything near these slots, or internal heat build-up may 
occur, causing picture degradation or damage to the projector.
6. Power sources
Check that the operating voltage of your unit is identical with the voltage of your 
local power supply.
7. Servicing
Do not attempt to service this projector yourself. Refer all servicing to qualified 
service personnel.
8. Replacement parts
When replacement parts are required, be sure that the replacement parts are 
specified by the manufacture. Unauthorized substitutions may result in fire, electric 
shock or other hazards.
9. Moisture Condensation
Never operate this projector immediately after moving it from a cold location to a 
warm one. When the projector is exposed to such a change in temperature, 
moisture may condense on the lens and the crucial internal parts. To prevent the 
unit from possible damage, do not use the projector for at least 2 hours when there 
is an extreme or sudden change in temperature. 
						

							 iii
Notes on the AC power cord
AC Power Cord must meet the requirement of countries where you use this projector. 
Please confirm your AC plug type with the graphics below and ensure that the proper 
AC Power Cord is used. If the supplied AC Power Cord does not match your AC 
outlet, please contact your sales dealer. This projector is equipped with a grounding 
type AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety 
purpose of this grounding type plug. We highly recommend using a video source 
device also equipped with a grounding type AC line plug to prevent signal interference 
due to voltage fluctuations.
For Australia and 
Mainland ChinaFor the U.S.A. and 
Canada
For the U.K.Ground
For Continental EuropeGround
GroundGround