ViewSonic Projector PJD6250L User Manual

							 10
Operating the Laser pointer
The laser beam is visible. It is necessary to press and 
hold LASER for continuous output.
The laser pointer is not a toy. Parents should be mindful of 
the dangers of laser energy and keep this remote control 
out of the reach of children.
Caution
• Do not look into the laser light window or shine the laser light beam on yourself or 
others. See the warning messages on the back of the remote control prior to using it.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more 
flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the 
remote control in place of your computer’s mouse. See Connection on page 14 
for details.
2. Set the input signal to COMPUTER.
3. Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse
mode.
4. Perform the desired mouse controls on your remote control.
• To move the cursor on the screen, press / / /  .
• To left-click, press  .
• To right-click, press  .
• To operate your display software program (on a connected PC) which responds 
to page up/down commands (like Microsoft PowerPoint), press Page Up/Page 
Down.
• To return to the normal mode, press Mouse again or other keys except for the 
mouse related multi-function keys.
Remote control code
The projector can be assigned to 8 different remote control 
codes, 1 to 8. When several adjacent projectors are in 
operation at the same time, switching the remote control 
codes can prevent interference from other remote 
controls. Set the remote control code for the projector first 
before changing that for the remote control.
To switch the code for the projector, select from among 1 
to 8 in the SYSTEM SETTING: ADVANCED > Remote 
Control Code menu. 
						

							 11
To switch the code for the remote control, press ID set and the corresponding button 
from 1 to 8 buttons on the remote control together for 5 seconds or more. The initial 
code is set to1. When the code is switched to 8, the remote control can control every 
projector.
Note
• If different codes are set on the projector and remote control, there will be no response 
from the remote control. When that happens, switch the code for the remote control 
again. 
						

							 12
Installing the batteries
1. Open the battery cover in the 
direction shown.
2. Install batteries as indicated by the 
diagram inside the compartment.
3. Close the battery cover into position.
Caution
•  Risk of explosion if battery is replaced by an incorrect type.
•  Dispose of used batteries according to the instructions.
•  Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
• Keep the battery out of the reach of children. 
• Remove batteries from remote control when not using for extended periods.
• Do not recharge the battery or expose the battery to fire or water.
• Do not dispose the used battery along with household waste. Dispose
 used batteries 
according to local regulations.
• Danger of explosion may happen if batteries are incorrectly replaced. Replace only with 
the same type recommended by the manufacturer.
• Battery should not be in or near to fire or water, keep batteries in a dark, cool and dry 
place. 
• If suspect battery leakage, wipe out the leakage and then replace a new battery. If the 
leakage adheres to your body or clothes, rinse well with water immediately. 
						

							 13
Remote control operation
Point the remote control at the infrared remote sensor and press a button.
• Operating the projector from the 
front.
Note
• The remote control may not operate when there is sunlight or other strong light such as 
a fluorescent lamp shining on the remote sensor.
• Operate the remote control from a position where the remote sensor is visible.
• Do not drop the remote control or jolt it.
• Keep the remote control out of locations with excessively high temperature or humidity.
• Do not get water on the remote control or place wet objects on it.
• Do not disassemble the remote control.
7m5m15
158m 
						

							 14
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Important
• In the connections shown above, some cables may not be included with the projector 
(see Package contents on page 2). They are commercially available from electronics 
stores.
• The connection illustrations above are for reference only. The rear connecting jacks 
available on the projector vary with each projector model.
• For detailed connection methods, see pages 15-17.
1. Audio cable 2. Microphone 3.5 mini jack cable
3. VGA (D-Sub) to HDTV (RCA) cable 4. S-Video cable
5. Composite Video cable 6. HDMI cable
7. USB cable (mini-B type to A type) 8. VGA cable (D-Sub to D-Sub)
9. VGA to DVI-A cable 10. HDMI/MHL dongle
2
13
1
456
7889
1
10 
						

							 15
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both 
IBM
® compatibles and Macintosh® computers. A Mac adapter is needed if you are 
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of 
the computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
Important
• Many notebooks do not turn on their external video ports when connected to a 
projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display 
on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol 
on the notebook. Press FN and the labeled function key simultaneously. Refer to your 
notebooks documentation to find your notebooks key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, 
you can connect the MONITOR OUT signal output socket on the projector to an 
external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in Connecting a computer on 
page 15.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to 
the D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable 
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the projector.
Important
• In standby mode, the MONITOR OUT output only works when COMPUTER IN 1 is 
made to the projector. 
						

							 16
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one 
of the following output sockets:
•HDMI
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the 
above connecting methods, however each provides a different level of video quality. 
The method you choose will most likely depend upon the availability of matching 
terminals on both the projector and the Video source device as described below:
Connecting an HDMI source device
Examine your Video source device to determine if it has a set of unused HDMI output 
jacks available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI 
source device.
2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component 
Video output sockets available:
Te r m i n a l  n a m eTerminal appearanceReferencePicture quality
HDMIHDMIConnecting an 
HDMI source 
device on page 16Best
Component VideoCOMPUTER IN 1/
COMPUTER IN 2Connecting a 
Component Video 
source device on 
page 16Better
S-VideoS-VIDEOConnecting an S-
Video source 
device on page 17Good
VideoVIDEOConnecting a 
composite Video 
source device on 
page 17Normal 
						

							 17
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3 RCA type 
connectors to the Component Video output sockets of the Video source device. 
Match the color of the plugs to the color of the sockets; green to green, blue to 
blue, and red to red.
2. Connect the other end of the cable (with a D-Sub type connector) to the COM-
PUTER IN 1 or COMPUTER IN 2 socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the 
correct video source has been selected, check that the Video source device is turned on 
and operating correctly. Also check that the signal cables have been connected 
correctly.
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output 
socket available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the
Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projec-
tor.
Important
• If the selected video image is not displayed after the projector is turned on and the 
correct video source has been selected, check that the Video source device is turned on 
and operating correctly. Also check that the signal cables have been connected 
correctly.
• If you have already made a Component Video connection between the projector and this 
S-Video source device using Component Video connections, you need not connect to 
this device using an S-Video connection as this makes an unnecessary second 
connection of poorer picture quality. See Connecting Video source devices on page 
16 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite 
Video output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device: 
						

							 18
1. Take a Video cable and connect one end to the composite Video output socket of
the Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the 
correct video source has been selected, check that the Video source device is turned on 
and operating correctly. Also check that the signal cables have been connected 
correctly.
• You need only connect to this device using a composite Video connection if Component 
Video and S-Video inputs are unavailable for use. See Connecting Video source 
devices on page 16 for details.
Playing sound through the projector
You can make use of the projector (mixed mono) speaker in your presentations, and 
also connect separate amplified speakers to the AUDIO OUT socket of the projector.
If you have a separate sound system, you will most likely want to connect the audio 
output of your Video source device to that sound system, instead of to the mono audio 
projector.
You can also use a microphone to output the sound through the projector speaker 
when the SYSTEM SETTING: ADVANCED > Audio Settings > Audio In 2 menu is 
set to Microphone. See Adjusting the Audio In 2 setting on page 51 for details.
Once connected, the audio can be controlled by the projector On-Screen Display 
(OSD) menus. See Adjusting the sound on page 50 for details.
About the microphone input
• If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the 
projector.
• There are two ways to adjust microphone volumes.
• Directly set microphone volume levels in the SYSTEM SETTING: ADVANCED 
> Audio Settings > Microphone Volume menu.
• Set projector volume levels in the SYSTEM SETTING: ADVANCED > Audio 
Settings > Audio Volume menu, or press Volume keys (+, -) on the remote 
control. (The projector volume setting will affect the microphone volume.)
• To make the microphone input available when the projector is in standby mode, turn 
on the SYSTEM SETTING: ADVANCED > Audio Settings > Active Audio out 
menu.
• If the microphone is not working, check the volume setting and cable connection.
• You might get feedback noise from the microphone when you are too close to the 
speaker of the projector. Move the microphone away from the speaker of the 
projector. The greater volume you require, the greater distance you need to be 
away from the Speaker to prevent the noise. 
						

							 19
Operation
Powering on/off the projector
Powering on the projector:
1. Complete the AC power cord and peripheral signal cable(s) connections.
2. Press   to turn on the projector.
The projector takes a minute or so to warm up. 
• If the projector is still hot from previous activity, it will run the cooling fan for 
approximately 60 seconds before energizing the lamp.
3. Turn on your source (computer, notebook, DVD, etc.).
• If you are connecting multiple sources to the projector simultaneously, press 
Source to select your desired signal or press your desired signal key on the 
remote control.
• If the projector doesnt detect a valid signal, the message No Signal will con-
tinue to be displayed.
• Be sure the Quick Auto Search function in the SOURCE menu is On if you 
want the projector to automatically search for the signals.
Warning
• Never look into the lens when the lamp is on. This can damage your eyes.
• This focal point concentrates high temperature. Do not place any object near it to avoid 
possible fire hazard.
Powering off the projector:
1. Press   to turn off the projector lamp. You will see a message Power off? Press 
Power again appear on the screen.
2. Press   again to confirm.
• When Active VGA out/Active Audio out function is turned off, the Power LED 
begins flashing and the projector has entered stand-by mode.
• When Active VGA out/Active Audio out function is turned on, the Power LED 
becomes steady light and the projector has entered stand-by mode.
• If you want to turn the projector back on, you must wait until the projector has 
completed the cooling cycle and has entered stand-by mode. Once in stand-by 
mode, simply press    to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.