ViewSonic Projector Pj358 User Manual

6ViewSonic	 PJ358
(a)
(b)
(a)(c) up
  (c) down
(b)
(c) up
  (c) down
Setting up
Settng	up
Install	the	projector	accordng	to	the	envronment	and	manner	the	projector	wll	be	
used	n.
Arrangement
Refer	to	the	llustratons	and	tables	below	to	determne	screen	sze	and	projecton	dstance.
The	values	shown	n	the	table	are	calculated	for	a	full	sze	screen:	1024×768.	
(a)	Screen	sze	(dagonal)
(b)	Projecton	dstance	(±10%)
(c)	Screen...

7ViewSonic	 PJ358
Setting up
WARNING		►Place	the	projector	n	a	stable	horzontal	poston.	If	the	
projector	falls	or	s	knocked	over	t	could	cause	njury	and/or	damage	to	the	
projector. Using a damaged projector could then result in fire and/or electric 
shock.
•		 Do	not	place	the	projector	on	an	unstable,	slanted	or	vbratonal	surface	such	
as	a	wobbly	or	nclned	stand.
•		 Do	not	place	the	projector	on	ts	sde,	front	or	rear	poston....

8ViewSonic	 PJ358
Setting up
Connecting your devices
Be	sure	to	read	the	manuals	for	devces	before	connectng	them	to	the	projector.	
Make	sure	that	all	the	devces	are	sutable	to	be	connected	wth	ths	product,	and	
prepare	the	cables	requred	to	connect.
Please	refer	to	the	followng	llustratons	to	connect	them.
WARNING		►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION...

9ViewSonic	 PJ358
Setting up
NOTE		•	Be	sure	to	read	the	manuals	for	devces	before	connectng	them	to	the	
projector,	and	make	sure	that	all	the	devces	are	sutable	to	be	connected	wth	ths	
product.	Before	connectng	to	a	PC,	check	the	sgnal	level,	the	sgnal	tmng,	and	the	
resoluton.
-		 Some	sgnal	may	need	an	adapter	to	nput	ths	projector.
-		 Some	PCs	have	multple	screen	dsplay	modes	that	may	nclude	some	sgnals...

10ViewSonic	 PJ358
Setting up
Using a USB storage
In	order	to	vew	mages	stored	n	a	USB	storage,	such	as	a	USB	memory	stck,	
nsert	the	devce	nto	the	USB	STORAGE	port.
For	more	nformaton,	please	see	the	“USB	STORAGE”.
Turn	the	projector	off	pror	to	removng	the	USB	storage	from	the	USB	STORAGE	
port,	to	prevent	some	troubles.
Connecting power supply
1.	Put	the	connector	of	the	power	cord	nto	
the	AC	nlet	of	the	projector.
2.	Frmly	plug...

11ViewSonic	 PJ358
Remote control
Putting batteries
Please	set	the	batteres	to	the	remote	control	before	usng	t.	If	the	remote	control	starts	
to	malfuncton,	try	to	replace	the	batteres.	If	you	wll	not	use	the	remote	control	for	long	
perod,	remove	the	batteres	from	the	remote	control	and	store	them	n	a	safe	place.
1.	Holdng	the	hook	part	of	the	battery	
cover,	remove	t.
2.	Algn	and	nsert	the	two	AA	batteres	
accordng	to...

12ViewSonic	 PJ358
Changing the frequency of  remote control signal
The	accessory	remote	control	has	the	two	choces	on	sgnal	
frequency	Mode	1	and	Mode	2.	If	the	remote	control	does	not	
functon	properly,	attempt	to	change	the	sgnal	frequency.
In	order	to	set	the	Mode,	please	keep	pressng	the	
combnaton	of	two	buttons	lsted	below	smultaneously	for	
about	3	seconds.
(1)	Set	to	Mode	1:	MUTE	and	RESET	buttons	
(2)	Set	to	Mode	2:	MAGNIFY 	OFF	and	ESC	buttons...

13ViewSonic	 PJ358
Turning on the power
1.	Make	sure	that	the	POWER	ndcator	turns	n	
steady	orange	and	the	lens	cover	s	removed.
2.	Press	the	STANDBY/ON	button	on	the	projector	or	
the	remote	control.	
The	projecton	lamp	wll	lght	up	and	the	POWER	
ndcator	wll	begn	blnkng	n	green.	When	the	power	
s	completely	on,	the	ndcator	wll	stop	blnkng	and	
lght	n	steady	green.	
To	dsplay	the...

14ViewSonic	 PJ358
Selecting an input signal
1.	Press	the	INPUT/ENTER	button	on	the	projector.		
Each	tme	you	press	the	button,	the	projector	swtches	
ts	nput	port	as	below.
										COMPUTER	IN1		 		COMPUTER	IN2		
										VIDEO				S-VIDEO				USB	STORAGE
Operating
Operatng
Adjusting the volume
1.	Press	the	VOLUME	button	on	the	remote	control.	
A 	dalog	wll	appear	on	the	screen	to	ad	you	n	adjustng	the	
volume.
2.	Use the ▲/▼ cursor buttons to...

15ViewSonic	 PJ358
Operating
Searching an input signal
1.	Press	the	SEARCH	button	on	the	remote	control.
The	projector	wll	start	to	check	ts	nput	ports	n	order	to	
find any input signals.
When	an	nput	s	found,	the	projector	wll	stop	searchng	and	
dsplay	the	mage. 	If 	no	 sgnal	s 	found, 	the	 projector 	wll	 return	 to	
the	state	selected	before	the	operaton.
									COMPUTER	IN1		 		COMPUTER	IN2		
										VIDEO				S-VIDEO		...