ViewSonic Projector Pj358 User Manual

56ViewSonic	 PJ358
USB STORAGE
Displaying an image in full screen (continued)
2) Button operation for motion picture
Whle	moton	pcture	s	shown	n	full	screen,	the	followng	operaton	can	be	made	
from	the	control	panel	on	the	projector	or	the	remote	control.
ButtonOperation
UPPause	and	play	moton	pcture.Play	ó	Pause
DOWNPlay	moton	pcture	slowly.	(half	speed)Play	ó	Play slowly (half speed) 
RIGHTFast-forward	moton	pcture.                Play	ð...

57ViewSonic	 PJ358
Mantenance
Lamp
A lamp has finite product life. Using the lamp for long periods of time could cause 
the	pctures	darker	or	the	color	tone	poor.	Note	that	each	lamp	has	a	dfferent	
lfetme,	and	some	may	burst	or	burn	out	soon	after	you	start	usng	them.
	
Preparaton	of	a	new	lamp	and	early	replacement	are	recommended.	 To	prepare	
a	new	lamp,	contact	your	dealer	and	tell	the	lamp	type	number.
Type number : RLC-027
Replacing the lamp
1.	Turn	the...

58ViewSonic	 PJ358
Maintenance
Lamp (continued)
Lamp warning
 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
WARNING		►The projector uses a high-pressure mercury glass lamp. The lamp can 
break	wth	a	loud	bang,	or	burn	out,	f	jolted	or	scratched,	handled	whle	hot,	or	worn	
over	tme.	Note	that	each	lamp	has	a	dfferent	lfetme,	and	some	may	burst	or	burn	
out	soon	after	you	start	usng	them.	In	addton,	when	the	bulb	bursts,	t	s	possble	for...

59ViewSonic	 PJ358
Please check and clean the air filter periodically. When the indicators or a 
message prompts you to clean the air filter, comply with it as soon as possible. 
Replace the air filter when it is damaged or too soiled. To prepare a new air filter, 
contact ViewSonic and tell the air filter type number.
When you replace the lamp, please replace the air filter. An air filter of specified 
type	wll	come	together	wth	a	replacement	lamp	for	ths	projector.
Cleaning the air...

60ViewSonic	 PJ358
Maintenance
Inside of the projector
In	order	to	ensure	the	safe	use	of	your	projector,	please	have	t	cleaned	and	
nspected	by	your	dealer	about	once	every	year.
Caring for the lens
If the lens is flawed, soiled or fogged, it could cause deterioration of display 
qualty.	Please	take	care	of	the	lens,	beng	cautous	of	handlng.
1.	Turn	the	projector	off,	and	unplug	the	power	cord.	Allow	the	projector	to	cool	
sufficiently.
2.	After	makng	sure	that	the...

61ViewSonic	 PJ358
Troubleshootng
If	an	abnormal	operaton	should	occur,	stop	usng	the	projector	mmedately.	
Troubleshooting
Otherwse	f	a	problem	occurs	wth	the	projector,	the	followng	checks	and	
measures	are	recommended	before	requestng	repar.
	
If	ths	does	not	resolve	the	problem,	please	contact	your	dealer	or	servce	
company.	 They	wll	tell	you	what	warranty	condton	s	appled.
Related messages
When	some	message...

62ViewSonic	 PJ358
Troubleshooting
Regarding the indicator lamps
When	operaton	of	the	LAMP,	TEMP	and	POWER	ndcators	dffers	from	usual,	
check	and	cope	wth	t	accordng	to	the	followng	table.
POWER indicatorLAMP indicatorTEMP indicatorDescription
Lghtng
In	
OrangeTurnedoffTurnedoffThe projector is in a standby state.
Please	refer	to	the	secton	“Power	on/off”.
BlinkingIn GreenTurnedoffTurnedoffThe projector is warming up.
Please	wat....

63ViewSonic	 PJ358
Troubleshooting
Regarding the indicator lamps (continued)
POWER 
indicator
LAMP 
indicator
TEMP 
indicatorDescription
Blinking
In Red
or
Lghtng In	
Red
Turned
off Lghtng
In	Red
There is a possibility that the interior portion 
has become heated.Please	turn	the	power	off,	and	allow	the	projector	to	
cool	down	at	least	20	mnutes.	 After	the	projector	has	
sufficiently cooled down, please make confirmation of 
the	followng	tems,	and	then	turn	the	power...

64ViewSonic	 PJ358
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects
About	the	phenomenon	confused	wth	a	machne	defect,	check	and	cope	wth	t	
accordng	to	the	followng	table.
PhenomenonCases not involving a machine defectReferencepage
Power	does	not	come	on.
The electrical power cord is not plugged in.
Correctly	connect	the	power	cord.10
The main power source has been interrupted during operation such as by a power outage (blackout), etc.
Please...

65ViewSonic	 PJ358
Phenomena that may be easy to be mistaken for machine defects (continued)
PhenomenonCases not involving a machine defectReferencepage
No	pctures	are	dsplayed.
(contnued)
The brightness is adjusted to an extremely low level.
Adjust	BRIGHTNESS	to	a	hgher	level	usng	the	menu	
functon	or	the	remote	control. 21,	23
The computer cannot detect the projector as a plug and play monitor.
Make	sure	that	the	computer	can	detect	a	plug	and	play	
montor	usng...