ViewSonic Pjl9371 Projector User Manual

PJL9371ViewSonic6

Part names
Remote control
(1) VIDEO button
(2) COMPUTER button
(3) SEARCH button
(4) STANDBY/ON button
(5) ASPECT button
(6) AUTO button
(7) BLANK button
(8) MAGNIFY - ON button
(9) MAGNIFY - OFF button
(10) MY SOURCE/DOC.CAMERA button
(11) VOLUME - button
(12) PAGE UP button *(13) PAGE DOWN button *(14) VOLUME + button
(15) MUTE button
(16) FREEZE button
(17) MY BUTTON - 1 button
(18) MY BUTTON - 2 button
(19) KEYSTONE button
(20) POSITION button
(21) MENU button
(22) ▲/▼/◄/► cursor...

PJL9371ViewSonic7

Setting up
Install the projector according to the environment and manner the projector will be 
used in.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection 
distance.
The values shown in the table are calculated for a full size screen: 1024 x 768
  a  Screen size (diagonal)   b  Projection distance (±10%)
 c1 , c2  Screen height (±10%)
On a horizontal surfaceSuspended from the ceiling
• Keep a space of 30 cm or more between 
the sides of...

PJL9371ViewSonic8

Setting up
►Place the projector in a stable horizontal position. If the 
projector falls or is knocked over, it could cause injury and/or damage to the 
projector. Using a damaged projector could then result in fire and/or electric 
shock.
•  Do not place the projector on an unstable, slanted or vibrational surface such 
as a wobbly or inclined stand.
•   Do not place the projector on its side, front or rear position. 
•   Consult with your dealer before a special installation such as...

PJL9371ViewSonic9

Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector. 
Make sure that all the devices are suitable to be connected with this product, and 
prepare the cables required to connect. Please refer to the following illustrations 
to connect them.
►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
WARNING
►Turn off all devices and unplug their power...

PJL9371ViewSonic0

Setting up
• Be sure to read the manuals for devices before connecting them to 
the projector, and make sure that all the devices are suitable to be connected 
with this product. Before connecting to a PC, check the signal level, the signal 
timing, and the resolution.
-  Some signal may need an adapter to input this projector.
-   Some PCs have multiple screen display modes that may include some signals 
which are not supported by this projector. 
-    Although the projector can...

PJL9371ViewSonic

Setting up
Connecting power supply
1.Put the connector of the power cord into the 
AC IN (AC inlet) of the projector.
2.Firmly plug the power cord’s plug into the 
outlet. In a couple of seconds after the 
power supply connection, the POWER 
indicator will light up in steady orange.
►Please use extra caution when connecting the power cord, as 
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If...

PJL9371ViewSonic

30º30º
Approx.3 m 
Remote control
Remote control
About the remote control signal
The remote control works with the projector’s remote 
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range 
when the sensor is active:
60 degrees (30 degrees to the left and right of the sensor) 
within 3 meters about.
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control...

PJL9371ViewSonic3

VIDEODOC.CAMERA
KEYSTONE
ASPECTSEARCHBLANK
MUTEMY BUTTON
POSITION
1 2
ESCENTER
MENU
RESET
COMPUTERMY SOURCE/AUTOMAGNIFYPAGE      UPVOLUME
DOWNoONOFF9×FREEZE

Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal 
frequency, Mode 1:NORMAL and Mode 2:HIGH. If the remote 
control does not function properly, attempt to change the 
signal frequency.
In order to set the Mode, please keep pressing the 
combination of...

PJL9371ViewSonic4

Power on/off
1.Make sure that the power cord is firmly and 
correctly connected to the projector and the 
outlet.
Turning on the power
2.Make sure that the POWER indicator is 
steady orange. Then remove the lens cover.
3.Press the STANDBY/ON button on the 
projector or the remote control.
The projection lamp will light up and the POWER  
indicator will begin blinking in green. When the power  
is completely on, the indicator will stop blinking and light in steady green.
Power...

PJL9371ViewSonic5

Operating
Operating
1.
Adjusting the volume
Use the VOLUME +/- buttons to adjust the volume. 
A dialog will appear on the screen to aid you in adjusting the 
volume. If you do not do anything, the dialog will automatically 
disappear after a few seconds.
●   When
  is selected for current picture input port, the volume 
adjustment is disabled. Please see the AUDIO SOURCE 
item of the AUDIO menu.
●   When the projector is in the standby state, the volume can be 
 
adjusted if  is...