ViewSonic Pjd6230 Projector User Manual

							
ViewSonic 14 PJD6220/PJD6230/PJD6240Menu OperationThe projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings. 
						

							
ViewSonic 15 PJD6220/PJD6230/PJD6240How to operate1. Press 
the Menu  button on the control panel or the  MENU button on the remote
control to open the OSD menu.
2. When OSD is displayed, use 
S / T to select any feature in the main menu.
3.
After selecting the desired main menu feature, press 
X to enter sub-menu for
feature setting
.
4.
Adjust
 the settings with 
W / X.
5. Press 
the  Menu  button
on the control panel or the 
MENU
 button on the remote
control, the screen will return to the main menu.
6. To exit OSD, 
press the 
Menu 
button 
on the control panel or the 
MENU
 button on
the remote control again. The OSD  menu will close and the projector will
automatically save the new settings.
Picture (Computer / Video Mode)Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, “Red”, “Green” and “Blue”
cab be adjusted.
Keystone
Correct the keystone distortion.
Aspect Ratio
Select how the picture fits on the screen:„
4:3 : The input source will be scaled to fit the projection screen.
„
16:9 : The input source will be scaled to fit the width of the screen.
Image
There are many factory presets optimized for various types of images.
„
PC : For computer or notebook.
„
Movie : For home theater.
„
sRGB : For PC standard color.
„
User : Memorize user’s settings.
Screen Type
Select the projection screen type.
White Intensity
Increase the brightness of white areas. 
						

							
ViewSonic 16 PJD6220/PJD6230/PJD6240GammaEffect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.Computer Image (Computer Mode)Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.Video Image (Video Mode)Color
Adjust the intensity of colors.
Sharpness
Sharpen or soften the image.
Tint
Shift colors toward red or green.Sound (Computer / Video Mode)Vo l u m e
Adjust the volume level.
Mute
Cut off the sound temporarily.Setting (Computer / Video Mode)Menu Position
Choose the menu location on the display screen.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Signal TypeSpecify the source to the Computer In terminal that you wish to project.„
Auto : Automatically choose the most suitable chroma subsampling scheme. Recommended!!
„
YPbPr : For component 480p,576p,720p,1080i signals.
„
RGB : For RGB video format. No subsamp ling. All information is accurately 
transmitted.
„
YCbCr : For component 480i,576i signals. 
						

							
ViewSonic 17 PJD6220/PJD6230/PJD6240Lamp Counter
Display the lamp’s elapsed operating time (in hours).
Lamp Counter Reset
Reset the lamp counter to 0 hours.
Power Saving
If no operation is performed for a specific period of time, the power to the projector is
automatically turned off.
Auto Source
Automatically scan the input source.
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life.
High Altitude
Turning on High Altitude mode operates the fans at full speed continuously to allow for
proper high altitude cooling of the projector.
Filter Mode
When an optional air filter is attached, be sure to turn on the “Filter Mode”; otherwise,
the machine can overheat and shutdown automatically.
OSD Timeout
Duration OSD menu stays active (at idle state by second).Option (Computer / Video Mode)Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Start-up Screen
Select start-up screen when the projector is powered on or when no signal is input.
User is the screen that you captured.
Screen Capture
Capture the current projection screen as a start-up screen.
Password
Set or change the password. When the password function is added, image projection
requires an entry of the preset password at power-on.
DCR (Dynamic Contrast Ratio)
Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable
DCR will resume to normal contrast performance. DCR will impact lamp life and
system noise performance.
Closed Caption (Video and S-Video sources only)
Enable or Disable closed captions by selecting CC1 (closed caption 1, the most
common channel), CC2 or OFF. 
						

							
ViewSonic18PJD6220/PJD6230/PJD6240Network Control
Select either RS232 or LAN for network control. If RS 232 is selected, user will not able
to control the projector via LAN network and vice ve rsa.Network ConfigDHCP„
Enable: Assign an IP address to the projector from t he DHCP server  
automatically. 
„
Disable: Assign an IP address manually. 
IP Address
Select an IP address. 
Subnet Mask
Select subnet mask number. 
Gateway
Select the default gateway of the network conn ected to the projector. 
Language (Computer / Video Mode)Select the language used by the on-screen menu.Factory Default (Computer / Video Mode)Restore all menu settings to factory default setting s. 
						

							
ViewSonic19PJD6220/PJD6230/PJD6240

Network Control
This feature provides the ability to remotely control and manage the pro\
jector through the network. 
Note: 1024x768 viewing resolution is recommended.
Preparation:
1. Connect one end of the internet cable to the LAN connector on projector.
2.  Connect the other end of the internet cable to an available LAN connector on the RJ45 outlet.
3.  Make sure the PC/NB is also connected to the internet.
4.  Turn on the projector and computer.
There are two ways to connect to the network control:
A. Auto IP address setting (DHCP):
  1. Enable DHCP from the projector OSD, under Network Config.
 2.  Please wait for the PC server to release IP address to the projector. DHCP icon will pop 
up on the bottom right corner, once the IP address is received by the projector. (It will 
take approx. 15 ~ 20 seconds).
  3.  Enter 
“Given IP address (For example http://10.0.50.100/)” into the address bar of the  
web browser and press “Enter” key or click “Go” button.
B.  Manual IP address setting:
1.    From your computer, go to 
Start > Control Panel > Network Connection and right click to 
select Properties. 
						

							
ViewSonic20PJD6220/PJD6230/PJD6240

2. Select “Intel Protocol (TCP/IP)” and click “Properties”.
3. Set your IP address on your computer, and click OK.
●
 
Click 
“Use the following IP address”
●
 
IP address: 10.0.50.105, (set the last number different to the projector IP address).
●
 
Subnet mask: 255.255.0.0 
						

							
ViewSonic21PJD6220/PJD6230/PJD6240

4.    Enter “http://10.0.50.100/” into the address bar of the web browser and press “Enter” key or \
click “Go” button.
5.  After the connection is completed, the control screen will be as below
Authority on the network control of Administrator & User:
ItemDescriptionAdministratorUser
StatusShow current projector status and network 
configuration settings.√√
Date & Time SettingDate & Time setting by user.√×
Control PanelControl the projector via network.√√
NetworkNetwork configuration & Password setup.√×
Alert SettingShow and setup Alert configurations.√×
ScheduleShow and setup Scheduling configurations.√× 
						

							
ViewSonic22PJD6220/PJD6230/PJD6240

Login
Enter “http://10.0.50.100/” into the address bar of the web browser and press “Enter” key or \
click “Go” button.
If the administrative and user password is disabled, it will directly go\
 into the Status page.
 
If the Administrative & User password is enabled
Select your User Name and enter password to login. 
						

							
ViewSonic23PJD6220/PJD6230/PJD6240

Status Information:
All screen images in this manual are shown when you login with the Administrator ID. The 
image will differ if you login with User ID.
ItemDescription
IP AddressShow current IP address.
Group NameShow group name.
Projector NameShow projector name.
System StatusShow if projector is Power On or Inactive *.
Input SourceShow current input source.
Lamp HoursShow lamp used hours on current projector.
Filter HoursShow filter used hours on current projector.
Projector StatusShow current projector status, either function normally or error found.
Date(y/m/d)Show date set on current projector.
TimeShow time set on current projector.
* when system status shows “Inactive”, it could either mean the pr\
ojector is “Power Off”, or 
projector’s network control is set to be RS232 (Please refer to Network Control, \
Page 18 to link 
with the project).