ViewSonic Pjd6230 Projector User Manual

							
ViewSonic 4 PJD6220/PJD6230/PJD6240Rear View 
Connection portsKensington lock
Rear IR remote control sensor
Ventilation holes
Bottom View
Elevator footCeiling mount (M4 x L7.5mm)
Tilt-adjustment foot
1
3
2
4
1234
12
3
123
„
This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package. 
						

							
ViewSonic 5 PJD6220/PJD6230/PJD6240Using the ProductControl PanelLED
Button Function
Lamp (Lamp LED indicator)
Refer to “LED Indicator Messages”.
Te m p  (Temperature LED indicator)
Refer to “LED Indicator Messages”. 
Four directional buttonsUse four directional buttons to select items or make adjustments to your  selection.EnterEnter to sub-menu and confirm the menu selection. Activate in Color Setting, LampCounter Reset and Factory Default menu operations.
Resync
Resynchronize the projector to the input signal from a computer.
Power
Turn the projector on or off.
MenuDisplay or exit the on-screen display menus.Source
Manually select an input source.
1
2
34
5
6
87
12345678 
						

							
ViewSonic 6 PJD6220/PJD6230/PJD6240Connection Ports
LAN
For network control.
Audio OutConnect to a speaker or other audio input equipment.Computer OutConnect to a computer display, etc.Audio InConnect an audio output from video equipment to this jack.Computer InConnect image input signal (analog RGB or component) to this jack.Computer InConnect image input signal (analog RGB or component) to this jack.RS-232When operating the projector via a computer, connect this to the controlling computers
RS-232C port.S-Video
Connect S-Video output from video equipment to this jack.
Video
Connect composite video output from video equipment to this jack.
SERVICEThis connector is for firmware update.
2
3
4
5
6
7
8
9
1
10
1212234344556677889910 
						

							
ViewSonic7PJD6220/PJD6230/PJD6240Remote Control
Power
Turn the projector on or off.
Four directional buttons
-Use four directional buttons to
select items or make adjustments
to your selection.
- The right button acts as Blank 
Screen function. Cut off the screen 
temporarily. Press again to cancel 
the Blank Screen function.
MENUDisplay or exit the on-screen display
menus.Laser
Aim the remote at the viewing
screen, press and hold this button
to activate the laser pointer.
Four directional buttons  
(Computer mode only)
Act as computer keyboard (four
directional buttons). This functionis only available when the projectoris connected to a computer via a
USB cable.
Left  (Computer mode only)
Act as mouse left button. This
function is only available when theprojector is connected to a computervia a USB cable.
Source
Manually select an input source.
Right  (Computer mode only)Act as mouse right button. This
function is only available when the
projector is connected to a compute r
via a USB cable.Enter
Confirm the selection.
Freeze
Press Freeze to pause the
screen image. 
Press again to cancel the Freeze
function.
1
1234567
891110
23456891011
ViewMatchSwitch in between high brightness
performance or Accuracy color
performance.
7 
						

							
ViewSonic 8 PJD6220/PJD6230/PJD6240Installing the Batteries1. Open the battery cover in the direction shown.
2. Install batteries as  indicated by the diagram
Inside the compartment.3. Close the battery cover into position.
„
Keep the batteries out of the reach of children. There is a danger of death by 
accidentally swallowing the batteries.
„
Do not recharge the used batteries or expose the batteries to fire or water.
„
Do not dispose of the used batteries along with household waste. Dispose of 
used batteries according to local regulations.
„
Danger of explosion may happen if batteries are incorrectly replaced. 
Replace only with the same type recommended by the manufacturer. 
						

							
ViewSonic 9 PJD6220/PJD6230/PJD6240Remote Control OperationPoint the remote control at the infrared remote sensor and press a button.„
Operating the projector from
the front
„
Operating the projector from
the rear
10
15
7m5m
5m
10
15
7m5m
5m
„
Do not point the laser pointer directly to the peoples eyes (especiallyn small 
children). There is a danger of injuiry to the eyes.
„
The remote control may not operate when there is sunlight or other strong light
such as a fluorescent lamp shining on the remote sensor.
„
Operate the remote control from a position where the remote sensor is visible.
„
Do not drop the remote control or jolt it.
„
Keep the remote control out of locations with excessively high temperature or
humidity.
„
Do not get water on the remote control or place wet objects on it.
„
Do not disassemble the remote control. 
						

							
ViewSonic 10 PJD6220/PJD6230/PJD6240
Installation
Connecting the Projector
VGA Cable (D-Sub to D-Sub) VGA (D-Sub) to HDTV (RCA) Cable
Audio Cable S-Video Cable
RS-232 Cable Composite Video Cable
USB Cable Internet Cable15
26
37
48
Desktop type
Laptop type
41112
7
3
6525
8
„When connecting cable, power cords of both a projector and external 
equipment should be disconnected from AC outlet.„The figure above is a sample connection. This does not mean that all of 
these devices can or must be connected simultaneously.
„The cables that come with the projector may differ from the above 
illustration. The included cables are based on actual shipment delivery. 
						

							
ViewSonic 11 PJD6220/PJD6230/PJD6240Powering On/Off the ProjectorPowering On the Projector:1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press   button to turn on the projector. The projector takes a minute or so to warm up. 
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
„
If you are connecting multiple sources to the projector simultaneously, press
the  Source  button.
Warning:
„
Remove the lens cap first before powering on.
„
Never look into the lens when the lamp is on. This can damage your eyes. It
is especially important that children are not allowed to look into the lens.
Powering Off the Projector:1. Press   button to turn off the projector lamp. You will see a message 
Power
off? Press Power again
 appear on the screen.   
2. Press   button again to confirm.
„
The cooling fans continue to operate for cooling cycle.
„
When the Lamp LED begins flashing, the projector has entered stand-by mode.
„
If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-
by mode, simply press   button to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector imm ediately following a power off procedure. 
						

							
ViewSonic 12 PJD6220/PJD6230/PJD6240Adjusting the ProjectorAdjusting the Projector HeightThe projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:1. To raise or lower the image, press the elevator button and raise or lower the frontof the projector. Release the button to lock the adjustment.2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.Adjusting the Projector Zoom and Focus1. Focus the image by rotating the focus  ring. A still image is recommended for focusing.2. Adjust the image by sliding the zoom ring. 
Elevator buttonElevator foot
Tilt-adjustment foot
„
To avoid damaging the projector, make sure that the elevator foot and tilt-
adjustment foot are fully retracted before placing the projector in its carrying 
case.
Focus ring Zoom ring 
						

							
ViewSonic 13 PJD6220/PJD6230/PJD6240Adjusting Projection Image SizeRefer to the graphic and table below to determine the screen size and projection distance.
Projection Distance (meters) Screen Size (for 4:3 aspect ratio diagonal length)
Wide (inches) Tele (inches)
1.2 30.08 27.34 2 49.96 45.57
3 74.94  68.35
5 124.90 113.92
10 249.80 227.83
30.08
(Min.)
49.96
74.94
124.90
249.80
(Max.)
227.83
113.9268.3545.57
27.34
1.2m
3.0m
5.0m
10.0m 2.0m
„
Position the projector in a horizontal position; other positions can cause heat 
build-up and damage to the projector.
„
Make sure the heat ventilation holes are not blocked.
„
Do not use the projector in a smoky environment. Smoke residue may cause 
build-up on critical parts (i.e. DMD, lens assembly, etc.)