ViewSonic Pj406d Projector User Manual

7
ViewSonic PJ406D

 Control Panel
1.  Temp Indicator LED
2.  Power Indicator LED
3.  Lamp Indicator LED
4.  Power/Standby 
5.  Menu (On/Off)
6.  Re-Sync
7.  Keystone Correction
8.  Four Directional  Select Keys
9.  Source
10.  Enter
TEMPLAMP
POWER
POWER/STANDBYMENU
SOURCERE-SYNC
1TEMP1TEMPTEMP1TEMPTEMP1
2
WWWWW
3LAMP3LAMPLAMP3LAMPLAMP3
4
107
 679
85 

8
ViewSonic PJ406D

 Connection Ports
1.  IR Receiver
2.  USB  Connector (service only)
3.  Monitor Loop-through Output Connector
4.  Composite Video Input Connector
5.  S-Video Input Connector
6.  Audio Input Connector
7.  PC Analog signal/SCART RGB/HDTV/Component Video 
Input  Connector
8.  KensingtonTM Lock Port
VGA-InS-VideoVideoVGA-OutUSBAudioServrvrice
1
8
234567 

9
ViewSonic PJ406D
Remote Control
1.  Power
2.  IR LED
3.  Hide 
4  Freeze 
5.  Source Lock
6.  Display Mode
7.  Menu
8.  Keystone Correction
9.  Whisper
10.  Volume+
11.  Volume-
12.  Reset
13.  Enter
14.  Four Directional     
Select Keys
15.  Re-Sync
16.  VGA Source
17.  Composite Video 
Source
18.  S-Video Source
 4
 5
 6
 15
 16
 9
 10
 11
 17
 8
 7
 13
 1 2
 3
 18
 12
 14 

10
ViewSonic PJ406D

 Connecting the Projector
 To ensure the projector works well with your computer, please set 
the display mode of your graphic card less than or equal to 1280 
X 1024 resolution. Make sure the timing of the display mode is 
compatible with the projector.  Refer to the “Compatibility Modes” 
section in User Guide.
 Due to the differ- 
  ence in applica-   
  tions for each    
  country, some    
  regions may have  
  different    
  accessories.
1....

11
ViewSonic PJ406D

Powering On the Projector
1.
  Remove the lens cap. 
2.  Ensure that the power cord and signal cable are securely 
connected.  The Power LED will turn Orange.
3.  Turn on the lamp by pressing “Power/Standby” button on 
the control panel.  
  The startup screen will display for 10 seconds and the Power 
LED will turn green.
4.   Turn on your source (computer, notebook, video player, 
etc.).  The projector will detect your source automatically.
 If you connect multiple sources at...

12
ViewSonic PJ406D

Warning Indicator
 When the “TEMP” indicator turns red, it indicates the projector 
has overheated. The projector will automatically shut itself down. 
 When the “LAMP” indicator turns red, it indicates a problem 
with the lamp.  Turn off the projector and disconnect the power 
cord from the electrical outlet, then contact your local dealer or our 
service center.
  When the “LAMP” indicator fl ashes red (1 second intervals), it 
indicates the fan failed.  Stop using the projector...

13
ViewSonic PJ406D

 Adjusting the Projected Image
Adjusting the Projector Image Height
The projector is equipped with an elevator foot for adjusting the 
image height.
 To raise the image:
1.  Press the elevator button 
.
2.  Raise the image to the desired height angle , then release  
  the button to lock the elevator foot into position.
3.  Use 
 to fi  ne-tune the display angle.
 To lower the image:
1.  Press the elevator button.
2.  Lower the image, then release the button to lock the eleva-
tor...

14
ViewSonic PJ406D...

15
ViewSonic PJ406D

T
E
M
P
L
A
M
P
P
O
W
E
R

P
O
W
E
R
/
S
T
A
N
D
B
Y
M
E
N
U

S
O
U
R
C
E
R
E
-
S
Y
N
C

Remote ControlControl Panel
 Control Panel & Remote Control
There are two ways for you to control the functions: Remote 
Control and Control Panel.
 Using the Control Panel
 Power/Standby  
  Refer to the “Power On/Off the Projector” section on pages  
    11-12.
 Source  
  Press “Source” to choose RGB, Component-p, Component-i,  
    S-Video, Composite Video and HDTV sources.
 Menu 
  Press...

16
ViewSonic PJ406D
 Using the Remote Control
  Power  
 Refer to the “Power On/Off the Projector” section on pages    11-12.
  Whisper  
 Using the button to turn on/off the whisper mode when whisper mode is on, acoustic noise and screen brightness are reduced.
 Volume +/- (Vol+/Vol-) 
 Increase/decrease speaker volume.
  Reset
 Changes the adjustments and settings to the factory default value.
  Keystone  / 
 Adjusts image distortion caused by tilting the projector (±15 de-grees).
  Hide
  “Hide”...