Home > ViewSonic > Projector > ViewSonic Pj406d Projector User Manual

ViewSonic Pj406d Projector User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual ViewSonic Pj406d Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 617 ViewSonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    7
    ViewSonic PJ406D
    
     Control Panel
    1.  Temp Indicator LED
    2.  Power Indicator LED
    3.  Lamp Indicator LED
    4.  Power/Standby 
    5.  Menu (On/Off)
    6.  Re-Sync
    7.  Keystone Correction
    8.  Four Directional  Select Keys
    9.  Source
    10.  Enter
    TEMPLAMP
    POWER
    POWER/STANDBYMENU
    SOURCERE-SYNC
    1TEMP1TEMPTEMP1TEMPTEMP1
    2
    WWWWW
    3LAMP3LAMPLAMP3LAMPLAMP3
    4
    107
     679
    85 
    						
    							
    8
    ViewSonic PJ406D
    
     Connection Ports
    1.  IR Receiver
    2.  USB  Connector (service only)
    3.  Monitor Loop-through Output Connector
    4.  Composite Video Input Connector
    5.  S-Video Input Connector
    6.  Audio Input Connector
    7.  PC Analog signal/SCART RGB/HDTV/Component Video 
    Input  Connector
    8.  KensingtonTM Lock Port
    VGA-InS-VideoVideoVGA-OutUSBAudioServrvrice
    1
    8
    234567 
    						
    							9
    ViewSonic PJ406D
    Remote Control
    1.  Power
    2.  IR LED
    3.  Hide 
    4  Freeze 
    5.  Source Lock
    6.  Display Mode
    7.  Menu
    8.  Keystone Correction
    9.  Whisper
    10.  Volume+
    11.  Volume-
    12.  Reset
    13.  Enter
    14.  Four Directional     
    Select Keys
    15.  Re-Sync
    16.  VGA Source
    17.  Composite Video 
    Source
    18.  S-Video Source
     4
     5
     6
     15
     16
     9
     10
     11
     17
     8
     7
     13
     1 2
     3
     18
     12
     14 
    						
    							
    10
    ViewSonic PJ406D
    
     Connecting the Projector
     To ensure the projector works well with your computer, please set 
    the display mode of your graphic card less than or equal to 1280 
    X 1024 resolution. Make sure the timing of the display mode is 
    compatible with the projector.  Refer to the “Compatibility Modes” 
    section in User Guide.
     Due to the differ- 
      ence in applica-   
      tions for each    
      country, some    
      regions may have  
      different    
      accessories.
    1. .............................................................................................................Power Cord2. ..............................................................................................................VGA Cable3. ........................................................................................Composite Video Cable4. ...................................................................S-Video Cable (Optional Accessory) 5. ...................................D-15 to RCA Adapter for YPbPr (Optional Accessory)
    S-Video Output
    Video Output
    DVD Player, Settop Box, HDTV receiver2
    1
    3
    5
    RGBUSB
    4   
    						
    							
    11
    ViewSonic PJ406D
    
    Powering On the Projector
    1.
      Remove the lens cap. 
    2.  Ensure that the power cord and signal cable are securely 
    connected.  The Power LED will turn Orange.
    3.  Turn on the lamp by pressing “Power/Standby” button on 
    the control panel.  
      The startup screen will display for 10 seconds and the Power 
    LED will turn green.
    4.   Turn on your source (computer, notebook, video player, 
    etc.).  The projector will detect your source automatically.
     If you connect multiple sources at the same time, use the  
    “Source” button on the control panel or remote control to       
    switch.
     Powering On/Off the Projector
    Turn on the projector 
    fi  rst and then the signal 
    sources.
    1
    Power/Standby
    2
    Lens Cap
    POWER/STANDBYRE-SYNC
    LAMP  
    						
    							
    12
    ViewSonic PJ406D
    
    Warning Indicator
     When the “TEMP” indicator turns red, it indicates the projector 
    has overheated. The projector will automatically shut itself down. 
     When the “LAMP” indicator turns red, it indicates a problem 
    with the lamp.  Turn off the projector and disconnect the power 
    cord from the electrical outlet, then contact your local dealer or our 
    service center.
      When the “LAMP” indicator fl ashes red (1 second intervals), it 
    indicates the fan failed.  Stop using the projector and disconnect 
    the power cord from the electrical outlet, then contact your local 
    dealer or our service center.
    Powering Off the Projector
    1. 
      Press the “Power/Standby” button to turn off the projec-
    tor lamp, you will see a message as below on the on-screen 
    display.
    2.  Press the “Power/Standby” button again to confi  rm. 
    3.  The cooling fans continue to operate for about 30 seconds for 
    cooling cycle and the Power LED will fl  ash orange.  When 
    the light stops fl  ashing, the projector has entered standby 
    mode.
      If you wish to turn the projector back on, you must wait 
    until the projector has completed the cooling cycle and has 
    entered standby mode.  Once in standby mode, simply press 
    “Power/Standby” button to restart the projector.
    4.   Disconnect the power cord from the electrical outlet and the 
    projector.
    5.  Do not turn on the projector immediately following a power 
    off procedure.  
    						
    							
    13
    ViewSonic PJ406D
    
     Adjusting the Projected Image
    Adjusting the Projector Image Height
    The projector is equipped with an elevator foot for adjusting the 
    image height.
     To raise the image:
    1.  Press the elevator button 
    .
    2.  Raise the image to the desired height angle , then release  
      the button to lock the elevator foot into position.
    3.  Use 
     to fi  ne-tune the display angle.
     To lower the image:
    1.  Press the elevator button.
    2.  Lower the image, then release the button to lock the eleva-
    tor foot into position. 
    3.  Use 
     to fi  ne-tune the display angle.
    Elevator Foot
    Elevator Button
     12
    33 
    						
    							
    14
    ViewSonic PJ406D
    
    Max.38.1"(96.8cm)76.2"(193.6cm)127.1"(322.7cm)177.9"(451.8cm)203.3"(516.3cm)254.1"(645.4cm)Min.34.7"(88.1cm)69.3"(176.1cm)115.6"(293.5cm)161.8"(410.9cm)184.9"(469.6cm)231.1"(587.0cm)Max.(WxH)30.5"x22.9"(77.4x58.1cm)61.0"x45.7"(154.9x116.2cm)101.7"x76.3"(258.2x193.6cm)142.3"x106.7"(361.4x271.1cm)162.6"x122.0"(413.0x309.8cm)203.3"x152.5"(516.3x387.2cm)Min.(WxH)27.8"x20.8"(70.5x52.9cm)55.4"x41.6"(140.9x105.7cm)92.5"x69.4"(234.8x176.1cm)129.4"x97.1"(328.7x246.5cm)147.9"x110.9"(375.7x281.8cm)184.9"x138.7"(469.6x352.2cm)4.9'(1.5m)9.8'(3.0m)16.4'(5.0m)23.0'(7.0m)26.3'(8.0m)32.8'(10.0m)
    
    Screen(Diagonal)
    Screen Size
    Distance
    Diagonal
    Adjusting the Projector Zoom / Focus
    You  may  turn  the  zoom  lever  to  zoom  in  or  out.    To  focus  the 
    image, rotate the  focus ring until the image is clear. The projec-
    tor  will  focus  at  distances  from  4.9  to  32.8  feet  (1.5  to  10.0  me-
    ters).
    Adjusting Projection Image Size
    This graph is for user’s reference only.
    Focus Ring
    Zoom Lever
    69.3"(176.1cm)
    115.6"(293.5cm)
    161.8"(410.9cm)
    184.9"(469.6cm)
    231.1"(587.0cm)
    38.1"(96.8cm)
    76.2"(193.6cm)
    127.1"(322.7cm)
    177.9"(451.8cm)
    203.3"(516.3cm)
    254.1"(645.4cm)
    4.9'
    32.8'
    26.3'
    23.0'
    16.4'
    9.8'
    (1.5m)
    (10.0m)
    (8.0m)
    (7.0m)
    (5.0m)
    (3.0m)
    34.7"(88.1cm) 
    						
    							
    15
    ViewSonic PJ406D
    
    T
    E
    M
    P
    L
    A
    M
    P
    P
    O
    W
    E
    R
    
    P
    O
    W
    E
    R
    /
    S
    T
    A
    N
    D
    B
    Y
    M
    E
    N
    U
    
    S
    O
    U
    R
    C
    E
    R
    E
    -
    S
    Y
    N
    C
    
    Remote ControlControl Panel
     Control Panel & Remote Control
    There are two ways for you to control the functions: Remote 
    Control and Control Panel.
     Using the Control Panel
     Power/Standby  
      Refer to the “Power On/Off the Projector” section on pages  
        11-12.
     Source  
      Press “Source” to choose RGB, Component-p, Component-i,  
        S-Video, Composite Video and HDTV sources.
     Menu 
      Press “Menu” to launch the on screen display (OSD) menu.  
        To exit OSD, press “Menu” again.
      Keystone     /   
      Adjusts image distortion caused by tilting the projector (±15  
        degrees).
     Four Directional Select Keys 
      Use         to select items or make adjustments to    
      your selection.
     Enter  
      Confi  rm your selection of items.
      Re-Sync  
      Automatically synchronizes the projector to the input source. 
    						
    							16
    ViewSonic PJ406D
     Using the Remote Control
      Power  
     Refer to the “Power On/Off the Projector” section on pages    11-12.
      Whisper  
     Using the button to turn on/off the whisper mode when whisper mode is on, acoustic noise and screen brightness are reduced.
     Volume +/- (Vol+/Vol-) 
     Increase/decrease speaker volume.
      Reset
     Changes the adjustments and settings to the factory default value.
      Keystone  / 
     Adjusts image distortion caused by tilting the projector (±15 de-grees).
      Hide
      “Hide” immediately turns the screen black. Press “Hide” again  
        to restore the displayed image.
      Freeze
     Press “Freeze” to pause the screen image.
     Source Lock
     Select auto detection all connector ports or lock current connector port.
     Display Mode
     Select the Display mode from PC, Movie, Game, sRGB and User.
      Menu  
     Press “Menu” to launch the on screen display menu.  To exit    OSD, press “Menu” again.
      Four Directional Select Keys 
     Use         to select items or make adjustments to    
     your selection.
      Enter
      Confi  rm your selection of items.
     Re-Sync
      Automatically synchronizes the projector to the input source.
     Composite
      Press “Composite” to choose Composite video source.
      S-Video
      Press “S-video” to choose S-video source.
      VGA
      Press “VGA” to choose VGA connector. 
    						
    All ViewSonic manuals Comments (0)

    Related Manuals for ViewSonic Pj406d Projector User Manual