ViewSonic Pj406d Projector User Manual

							
17
ViewSonic PJ406D

The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.  To open the OSD menu, press “Menu ” on the Remote Control  
  or Control Panel.
2. When OSD is displayed, use     keys to select any item in the  
  main menu.  While making a selection on a particular page, press  
  or “Enter” key to enter sub menu.
3. Use      keys to select the desired item and adjust the   
  settings by 
    key.  
4. Select the next item to be adjusted in the sub menu and adjust as  
  described above.   
5. Press “Menu ” to confi  rm, and the screen will return to the  
  main menu.
6.  To exit, press “Menu ”again.  The OSD menu will close and the  
  projector will automatically save the new settings.
 On Screen Display Menus
Main Menu
Sub MenuSetting 
						

							
18
ViewSonic PJ406D

Menu Tree
Image-I Display mode PC/Normal/Movie/sRGB/User
Brightness Contrast
White intensity
Colour temp.
Video Saturation
Sharpness
Image-II Computer Frequency
Computer Phase
Computer Hor. position
Computer Ver. position
Degamma
Aspect ratio 16:9/4:3
Ver. Shift(16:9)
Colour setting  Red
Green Blue
Yellow Cyan
Magenta
Language English/Deutsch/Français/Italiano/Español/
Português/Nederlands/
����/����/���/���Management Menu location
ProjectionKeystone
Source lock On/Off
High altitude On/Off
Translucence VolumeReset Execute/Cancel
Lamp setting Projection hours
Lamp hoursLamp reset Execute/Cancel
Lamp reminding On/Off
Sleep timer
Whisper mode
On/Off
Auto power off 
						

							
19
ViewSonic PJ406D

 Language
 Language
  Choose the multilingual OSD menu . Use the   or  key to  
  select your preferred language. 
  Press “Enter” to fi  nalize the selection. 
Colour Setting
 Colour Setting
 Adjust the Red, Green, Blue, Yellow, Cyan and Magenta colors for  
  advanced adjustment of the individual colors.   
						

							
20
ViewSonic PJ406D

Image-I
 Display Mode
 There are many factory presets optimized for various types of  
  images.  
  PC: For computer or notebook.
  Movie: For home theater.
  Normal: For normal viewing condition.
  sRGB: For standard color.
  User: Memorize user’s settings.
 Brightness
 Adjust the brightness of the image.
  Press the  to darken image.
  Press the  to lighten the image.
 Contrast
 The contrast controls the degree of difference between the lightest  
  and darkest parts of the picture. Adjusting the contrast changes  
  the amount of black and white in the image.
  Press the  to decrease the contrast.
  Press the  to increase the contrast.
 White Intensity
 Use the white peaking control to set the white peaking level of  
  DMD chip. 0 stands for minimal peaking, and 10 stands for    
  maximum peaking.  If you prefer a stronger image, adjust towards  
  the maximum setting.  For a smooth and more natural image,  
  adjust towards the minimum setting.
 Color Temp.
 Adjust the color temperature. At higher temperature, the screen  
  looks colder; at lower temperature, the screen looks warmer.   
						

							
21
ViewSonic PJ406D

“Saturation” function is not supported under computer mode.
 Saturation
 Adjusts a video image from black and white to  fully saturated  
  color.
  Press the  to decrease the amount of color in the image.
  Press the  to increase the amount of color in the image. 
 Sharpness 
 Adjusts the sharpness of the image.
  Press the  to decrease the sharpness.
  Press the  to increase the sharpness.  
						

							
22
ViewSonic PJ406D

Image-II
 Frequency
  “Frequency”changes the display data frequency to match the  
  frequency of your computer’s graphic card. If you experience a  
  vertical fl  ickering bar, use this function to make an adjustment.
 Phase
  “Phase” synchronizes the signal timing of the display with the  
  graphic card. If you experience an unstable or fl  ickering image,  
  use this function to correct it.
 Hor. Position (Horizontal Position)
  Press the  to move the image left. 
  Press the  to move the image right. 
 Ver. Position (Vertical Position)
  Press the  to move the image down.
  Press the  to move the image up.
 Degamma
This allows you to choose a degamma table that has been fi  ne-tuned 
to bring out the best image quality for the input.
 Aspect Ratio
 Use this function to choose your desired aspect ratio.
 4:3 : The input source will be scaled to fi  t the projection screen. 
 16:9 : The input source will be scaled to fi  t the screen width.
 Ver. Shift (16:9)
 Adjust the image position to up or down, when you select the    
  aspect ratio to 16:9.
  Press the  to move the image down.
  Press the  to move the image up.
“Frequency/Phase/Hor. Position/Ver.posi-tion” function is not 
supported under video  
mode.   
						

							
23
ViewSonic PJ406D

 Menu Location
  Choose the menu location on the display screen.
 Projection
    Front-Desktop 
    The factory default setting. 
    Rear-Desktop 
    When you select this function, the projector reverses the image  
    so you can project behind a translucent screen.
    Front-Ceiling 
    When you select this function, the projector turns the image  
    upside down for ceiling-mounted projection.
    Rear-Ceiling 
    When you select this function, the projector reverses and turns  
    the image upside down at same time. You can project from   
    behind a translucent screen with ceiling mounted projection.
 Keystone
  Correct image distortion caused by tilting the projector vertically. 
 Source Lock
 When this function is turned off, the projector will search for other 
signals if the current input signal is lost. When this function is 
turned on, it will search specifi  ed connection port.
 High Altitude
Choose “On” to turn on High Altitude mode. Operates the fans at 
full speed continuously to allow for proper high altitude cooling of 
the projector.
Management      
						

							
24
ViewSonic PJ406D

 Translucence
  Choose the menu transparency on the display screen.
 Volume
  Press the  to decrease the volume. 
  Press the  to increase the volume. 
 Reset
 Return the adjustments and settings to the factory default values.
  Execute: Returns the settings for all menus to factory default  
  values.
  Cancel: Cancel the revised settings
  
						

							
25
ViewSonic PJ406D

 Projection Hours
 Display the projection time.
 Lamp Hours
 Display the cumulative lamp operating time.
 Lamp Reset
 Reset the lamp life hour after replacing a new lamp. 
 Lamp Reminding
 Choose this function to show or to hide the warning message when 
the changing lamp message is displayed. The message will show up 
30 hours before end of life.
 Whisper Mode
 Choose “On” to dim the projector lamp which will lower power 
consumption and extend the lamp life by up to 130%. Choose ”Off” 
to return to normal mode.
 Auto Power Off
 Sets the interval of power-off of the system, if there is no signal 
input. (In minutes)
 Sleep Timer
 Sets the interval of power-off of the system, if there is no signal 
input. (In minutes)
Lamp Setting  
						

							
26
ViewSonic PJ406D

Problem: No image appears on screen.
 Ensure all the cables and power connections are correctly and  
  securely connected as described in the “Installation” section.
 Ensure the pins of connectors are not crooked or broken.
 Check if the projection lamp has been securely installed. Please  
  refer to the “Replacing the lamp” section.
 Make sure you have removed the lens cap and the projector is  
  switched on.
 Ensure that the “Hide” feature is not turned on.
Problem: Partial, scrolling or incorrectly displayed image.
  Press “Re- sync” on the Remote Control or on the  Control Panel.
  If you are using a PC:
 For Windows 3.x:
 1.   In the Windows Program Manager, double click the “Windows 
    Setup” icon in the Main group.
 2.   Verify that your display resolution setting is less than  or equal  
   
to 1280 x 1024.
 For Windows 95, 98, 2000, XP:
 1.   From the “My Computer” icon, open the “Control Panel”  
    folder, and double click the “Display” icon.
 2.   Select the “Settings” tab  
 3.  Click on the “Advanced Properties” button.
  If the projector is still not projecting the whole image, you will  
  also need to change the monitor display you are using. Refer to  
  the following steps.
 Troubleshooting
 If you experience trouble with the projector, refer to the fol-
lowing information.  If the problem persists, please contact 
your local reseller or service center.