Vidikron Projector Vision Model 70 User Manual

Operation
Vidikron Vision 70 Series Owner’s Operating Manual 59 
PREL
IMINARY
Splash Screen Timer: Use the  or  button to set the Splash Screen Timer. This timer 
controls how long the startup (ISF and Vidikron logo) image stays on-screen after you turn on 
the projector. Select from 5 to 60 seconds, in one-second increments. When finished, press 
EXIT. 
ISF Enable: Select ISF Enable from the ISF Calibration menu to control the display of the ISF 
logo on the Vision 70 splash screen upon power-up. 
You...

Operation
60 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
Notes: 

Vidikron Vision 70 Series Owner’s Operating Manual 61 
PREL
IMINARY
5.1 
Lamp Replacement
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or 
sooner if a noticeable degradation in brightness occurs. Contact your Vidikron dealer to 
obtain a replacement lamp.
1. Turn off the projector and unplug the power cord. 
Allow the projector to cool down for 
approximately 45 minutes prior to removing the 
lamp assembly for replacement.
2. Remove the three screws from the...

Maintenance and Troubleshooting
62 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
5.2 
Troubleshooting Tips
Table 5-1 provides some general guidelines for troubleshooting problems you may 
encounter with the Vision 70. If the suggested solutions fail to resolve the problem or if you 
encounter an issue not described here, please contact Vidikron Technical Support. 
Table 5-1. Troubleshooting Chart 
SymptomPossible Cause(s)Solution
The projector does not turn on.  The Vision 70 is not...

Maintenance and Troubleshooting
Vidikron Vision 70 Series Owner’s Operating Manual 63 
PREL
IMINARY
Colors in the image are 
swapped; for example, reds 
appear blue or vice versa.  The Red/Pr, Green/Y or 
Blue/Pb outputs from the 
source are connected to the 
wrong inputs on the Vision 
70. Ensure that the source 
outputs are connected to 
the correct Vision 70 input. 
TEMP and LAMP LEDs are both 
flashing red.  The lamp cover is open.
 Fans are not working 
properly.
 Close the lamp cover.
 Please...

Maintenance and Troubleshooting
64 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
Notes: 

Vidikron Vision 70 Series Owner’s Operating Manual 65 
PREL
IMINARY
6.1 
RS-232 Connection and 
Port Configuration
To interface the Vision 70 with a home theater automation/control system or a PC running 
terminal emulation software:
1. Connect it to your control system or PC as shown in Figure 3-12. 
2. Start a terminal session on your PC using a terminal-emulation program, such as 
HyperTerminal. 
3. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop 
bit and...

Serial Communications
66 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
x023xKeypad 3
x024xKeypad 4
x025xKeypad 5
x026xKeypad 6
x027xKeypad 7
x028xKeypad 8
x029xKeypad 9
x030xKeypad 0
x031xStore image settings to Custom 1
x032xStore image settings to ISF Night
x033xStore image settings to ISF Day
x046xRestore image settings from Custom 1
x047xRestore image settings from ISF Night
x048xRestore image settings from ISF Day
x049xLoad default of current source
x051xSingle source, full-screen...

Serial Communications
Vidikron Vision 70 Series Owner’s Operating Manual 67 
PREL
IMINARY
x081xImage orientation = floor front
x082xImage orientation = ceiling front
x083xImage orientation = floor rear
x084xImage orientation = ceiling rear
x091xLamp Power = 200W
x092xLamp Power = 250W
x121xOSD Language = English
x122xOSD Language = French
x123xOSD Language = Spanish
x124xOSD Language = German
x125xOSD Language = Italian
x131xSwitch to Composite input
x132xSwitch to S-Video input
x133xSwitch to RGB-HD...

Serial Communications
68 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
x282xVertical Lens Shift = Max. Down
x283xZoom = Max. Out
x284xZoom = Max. In
x285xFocus (rotate lens to right, full-range)
x286xFocus (rotate lens to left, full-range)
x287xAperture Control = Full On (open)
x288xAperture Control = Full Off (closed)
Table 6-1. Serial Commands (continued)
Code Function