Vidikron Projector Vision Model 70 User Manual

Operation
Vidikron Vision 70 Series Owner’s Operating Manual 49 
PREL
IMINARY
Color Select: Use the Color Select menu to select the color space that is appropriate for the 
source signal, to achieve optimal color balance. 
If you select NTSC, HDTV or PAL, you can make further adjustments to individual color space 
characteristics in the 
ICC Adjust sub-menu under the ISF Calibration menu, described later in 
this section. (The Standard color space is factory-set and not adjustable.) 
Image OptionInput...

Operation
50 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
Table 4-1. Aspect Ratio Settings 
Aspect Ratio
Remote 
Control
Key
Description
Anamorphic 
(16:9)ANASelect Anamorphic to view 
16:9 DVDs and HDTV 
programs in their native 
aspect ratio. 
 
 
 
 
 
4:3 images are stretched 
horizontally to fit a 16:9 
screen. 
Standard 4:34X3Standard 4:3 scales the input 
signal to fit in the center of 
the 16:9 screen. 4:3 is the 
aspect ratio used by 
computer monitors, 
standard television...

Operation
Vidikron Vision 70 Series Owner’s Operating Manual 51 
PREL
IMINARY
SD Enhance: The SD Enhance menu gives you options for improving the quality of 
standard-definition, 480i images. (For 480p and higher-definition images, the controls in this 
menu are disabled.) Keep in mind that these controls add frequencies that are not present in 
the original signal, and may make images appear “noisy” if misused. 
• H Enhance/V Enhance: These controls can improve the apparent horizontal and/or 
vertical...

Operation
52 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
Video Filter: The Video Filter setting controls the behavior of the Sharpness control. The 
available settings depend on the vertical resolution of the input signal, as follows: 
With a 480i signal, you can apply the sharpness control to either the input signal (1), the 
output signal (2), both (3) or neither (0). 
With a 480p or higher-resolution signal, the sharpness control is applied only to the 
output signal and only when...

Operation
Vidikron Vision 70 Series Owner’s Operating Manual 53 
PREL
IMINARY
Lamp Hours: Lamp Hours indicates how long the currently-installed lamp has been in 
service. (This part of the menu is read-only.)
InstallationTo access the Installation adjustments, press MENU, then press the  or  button to 
highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears. 
Press EXIT to return to the previous menu or press MENU to close all menus. 
Language: Press the  or  button to...

Operation
54 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
ServiceTo access advanced projector settings, use the up- or down-arrow keys to select Service from 
the Main Menu and press ENTER. Use the number buttons on the remote to enter the Service 
menu passcode when prompted and press ENTER again. Then, press MENU on the remote 
control. 
White Balance: To remove any trace of color from the white areas of the projected image, 
choose White Balance from the 
Service menu and press...

Operation
Vidikron Vision 70 Series Owner’s Operating Manual 55 
PREL
IMINARY
ICC Adjust: Use the ICC Adjust controls to customize the stored NTSC, HDTV and/or PAL 
color space characteristics. To do this, select the color space to modify. Then, select a 
component color (Red, Green, Blue, Yellow, Cyan or Magenta). 
For each component color, you can adjust the following: 
•Intensity: This slidebar adjusts the intensity – also known as luminance – of a given color. 
•Sat. This slidebar adjusts the color...

Operation
56 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
Image Shift: The Image Shift menu allows you to precisely center the image on the screen. 
(These controls are available only with a 480i source signal.) 
• Horizontal: This control moves the image right or left within the area of available pixels. 
• Vertical: This option moves the image up or down within the area of available pixels. 
Amplitude: The Amplitude menu allows you to fine-tune the currently-selected image 
aspect...

Operation
Vidikron Vision 70 Series Owner’s Operating Manual 57 
PREL
IMINARY
RS-232 Baud Rate: To change the data rate of the projector’s RS-232 input, select RS-232 
Baud Rate from the Service menu. Set it to either 9600, 38400 or 115200, to match the data 
rate of the computer or control system connected to the projector.
Remote Control: The Remote Control menu shows you the primary and secondary infrared 
(IR) codes to which the Vision 70 will respond. The Primary IR code is permanently set to +20....

Operation
58 Vidikron Vision 70 Series Owner’s Operating Manual
PREL
IMINARY
ISF CalibrationTo access the ISF Calibration menu, select ISF Calibration from the Main Menu and press 
ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu 
passcode when prompted and press ENTER again. Then, press MENU on the remote control. 
Picture Adjust: These settings are described in the Picture Adjust section (page 44). 
White Balance / Gamma Selection / Aperture Control: These settings...