Home > Uniden > Communications receiver > Uniden Receiver BC245XLT Operating Instructions

Uniden Receiver BC245XLT Operating Instructions

    Download as PDF Print this page Share this page

    Have a look at the manual Uniden Receiver BC245XLT Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 50 Uniden manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							4. Enter the frequency.
    a.Enter the frequency
    number.
    b.Then press .
    Note:To clear a mistake while entering the frequency,
    press repeatedly until the display is cleared.
    If you enter a
    frequency which is
    outside the scanner’s
    frequency bands, a
    distinctive beep
    sounds andError
    appears in
    the display.
    Press and go back
    to Step 4.
    (See the Table on page 3 or the Band List on the
    back of the scanner).
    17
    12345678 910
    12345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:01:56 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							Duplicate Frequency Alert
    If you enter a
    frequency which is
    stored in another
    channel, you hear a
    beep and the other
    channel displays.
    Press to clear and
    start again.
    —OR—
    Press again to
    store the frequency in
    both channels.
    Programming Tips
    nDo not program a weather frequency into one of
    the channels, since weather channels transmit
    continuously.
    Use Service Scan feature to select the weather
    information band.
    nGroup similar frequencies into adjacent channels.
    For example, program police frequencies in
    channels 1 through 10 and fire/emergency into
    channels 11 through 20, and so on.
    nPut the frequency that you listen to the most or the
    most important frequency into a Priority channel.
    nTo quickly program a series of channels, start with
    the lowest number channel.
    For example, when you are programming five new
    frequencies into Channels 4 through 8, start with
    Channel 4. After you finish programming a
    channel, press or to go to the next
    higher channel.
    nWrite down your programmed channels and
    frequencies in some convenient place in case the
    scanner memory is lost.
    nIf you want to download frequencies using
    SmartScan feature, go to that section in this
    manual.
    18
    12345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:01:57 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							Deleting a Stored Frequency
    To delete a stored
    frequency:
    a. Select a
    channel.
    b. Press .
    c. Then press .
    Note: Channels with no frequencies are automatically
    locked out.
    1912345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:01:58 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							Scanning
    1. After programming
    frequencies, simply
    press to begin
    scanning.
    2. The bank indicators selected for scanning appear in
    the display, and the bank being currently monitored
    flashes. You can deselect banks from active
    scanning by pressing their number on your keypad.
    The indicator for each deselected bank turns off, and
    the bank’s channels are not scanned.
    Note:One Bank must always be active. You cannot
    deactivate all ten banks at the same time. If you try
    to turn all the banks off, the first bank is
    automatically selected.
    To restore a bank to active scanning, press the
    bank’s number on your keypad. The bank’s indicator
    will display again.
    3. During normal
    scanning the scanner
    skips unprogrammed
    or locked
    out channels.
    4. When a transmission
    is received, the LCD
    back light comes on
    for five seconds and
    the scanner stops on
    that channel, provided
    that you have
    selected the Auto
    Light feature. When
    the transmission
    ends, scanning
    resumes
    automatically.
    2012345678 910
    1 3 4 5 9  102 6 7  8CHANNELS
    Frequency not
    entered Frequency
    Locked Out
    (L/O)
    SCAN
    12345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:02:00 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							If you want to stop on
    a channel during
    scanning, press .
    If you want to resume
    scanning, press .
    To directly access a specific channel:
    1. Press .
    2. Enter the channel
    number you want
    using the keypad.
    3. Press again.
    RF Attenuation Feature
    TheBC245XLTcomes with an RF Attenuation feature. If
    you’re near an unusually strong signal source, the signal
    may overload the scanner. The scanner may stop
    repeatedly on that signal and miss other transmissions.
    The RF Attenuation feature works in all modes and
    attenuates (reduces) the incoming signal strength by about
    15 dB, preventing stronger signals from overloading the
    scanner.
    To turn RF Attenuation on:
    1. PressATT.
    21
    12345678 910
    12345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:02:02 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							2. You hear a beep, and
    ATTappears in the
    display begins
    flashing.
    Now all incoming
    signal strength is
    reduced.
    To turn RF Attenuation off, just press
    ATTagain. TheATT
    icon goes out.
    Setting the Delay Mode
    A delay can be set for each programmed channel so that
    when scan or search stops on a channel there is a brief
    pause before the scanning cycle resumes. Delay must be
    set for each programmed channel and it can be set when
    your scanner pauses during a scan or when manual mode
    is selected.
    Delay in Scan or Search Mode
    1. Press or set a
    search range and
    press .
    2. When your scanner
    stops on a channel
    that you want to
    delay, press .
    DLYdisplays and
    scanning resumes two
    seconds after the
    transmission ends.
    22
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:02:04 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							Delay in Manual Mode
    1. Press .
    2. Select the channel
    that you want by
    entering the number
    and press .
    Press and
    DLY
    displays indicating the
    scanner will pause on
    the channel when a
    transmission is
    received.
    Channel Lockout
    You can lockout any channel so it is not reviewed during
    normal scanning. You can restore the channel to scanning
    whenever you wish.
    Lockout in Manual Mode
    1. Press .
    2. Select a channel.
    Enter the channel
    numbers. Press
    again.
    —OR—
    Press or
    to change higher, or
    to lower
    the channel.
    3. Press to lockout
    the channel.
    L/O appears
    in display.
    23
    12345678 910
    12345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:02:06 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							Lockout in Scanning Mode
    If the scanner keeps stopping on a particular channel due
    to noise or too frequent transmissions, you may want to
    keep that channel from scanning.
    1. Wait until the scanner
    stops at the channel.
    2. Then press .
    3. The scanner
    immediately resumes
    scanning because the
    locked out channel is
    no longer in the
    scanning sequence.
    Lockout Tips
    nTo quickly lockout a series of channels, start with
    the lowest number channel.
    For example, if you are locking out channels 4, 7,
    8, 12, and 15, start with Channel 4. After selecting
    channel 4, press . Then press one or more
    times to step up to the next channel to be
    locked out.
    nRecord the locked-out channels in some
    convenient place so you can restore them.
    24
    12345678 910
    12345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:02:07 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							Restore a Locked Out Channel
    1. Press .
    2. Select a locked out
    channel.
    a.Enter the channel
    number.
    b. Then press
    again.
    3. Press to unlock
    the channel. The
    L/O
    icon goes out.
    Restore All Locked-Out Channels
    You can restore all locked-out channels in a bank only
    when a bank is selected for scan. If you have deselected a
    bank and you want to restore all of its locked-out channels
    using the steps below, you must press and then press
    the number of the bank on your keypad.
    1. Press .
    Note:You must be in
    Manual mode before
    restoring all
    locked-out channels.
    25
    12345678 910
    12345678 910
    12345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:02:09 1999 Color profile: Disabled
    Composite  Default screen 
    						
    							2. Press and hold for
    about two seconds.
    You will hear two
    beeps when all the
    channels have
    been restored.
    Priority Scan
    When Priority Scan is turned on, your scanner checks the
    priority channel every two seconds for activity. If a signal is
    present on the priority channel, your scanner monitors the
    channel until the transmission ends, then resumes normal
    scanning. You can designate one channel in each bank as
    a Priority Channel.
    To activate Priority Scan (in either the Manual or
    Scan Mode):
    1. Press .
    Note:If you have
    locked out the priority
    channel, this message
    appears when you
    select Priority mode.
    2. Press
    again at anytime to
    deactivate Priority
    Scan.
    26
    12345678 910
    C:\Manuals\BC245XLT\BC245XLT.VP
    Tue Jun 15 11:02:10 1999 Color profile: Disabled
    Composite  Default screen 
    						
    All Uniden manuals Comments (0)

    Related Manuals for Uniden Receiver BC245XLT Operating Instructions