Home > Uniden > Communications receiver > Uniden Bc9000xlt Wideband Scanner Owners Manual

Uniden Bc9000xlt Wideband Scanner Owners Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Uniden Bc9000xlt Wideband Scanner Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 50 Uniden manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Using Turbo Search
    Turbo Search increases the search speed from 100 frequencies per
    second to 300 frequencies per second in ranges where the frequencies
    are spaced 5 kHz apart.
    Use these keys:
    While searching, presst.
    Using Search Delay
    On some two-way channels there might be short lapses in the signal
    before a reply. The Search Delay feature causes the scanner to wait two
    seconds after the end of a transmission before resuming searching, in
    case there is a reply.
    Unlike Scan Delay, you don’t have to turn on Search Delay for each
    frequency in the search range. Search Delay works for the entire
    frequency range you chose.
    PressYto turn Search Delay ON.
    31
    COUNT         AUX          STATUS
    SCAN
    SRCMANUAL
    AUTO PROG SEND ALPHA
    HOLD
    LIMIT MEM SHIFT
    LINEEXT SP
    PRI   TURBO        CTCSS             DATA
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT
    L/O                DELAY                ATT
    12
    4
    75
    8
    03
    6
    9
    E
    A
    FB
    GC
    HD
    IE
    JFREQ
    CHAN
    LOCKSQUELCH
    VOLUME
    OFF
    BC XLT9000
    TWIN TURBO
    PRI   TURBO        CTCSS             DATA
    L/O                DELAY                ATT
    Mode Keys
    SRC NFM 5. 0 KHz
    MHz 4 6.0150T 
    						
    							Locking Out Frequencies
    This feature is similar to locking out a programmed channel, except you
    can only lock out 50 frequencies.
    Use these keys:
    While searching pressLwhen the
    scanner stops on an undesired
    frequency.
    Search resumes immediately.
    Unlocking a Frequency
    1. Presshto stop the
    search.
    2. Pressto find
    the frequency you want to
    unlock. Or chooseFREQwith
    the Rotary Tuner Mode Selector
    and tune in the frequency.
    3. PressL.
    32
    COUNT         AUX          STATUS
    SCAN
    SRCMANUAL
    AUTO PROG SEND ALPHA
    HOLD
    LIMIT MEM SHIFT
    LINEEXT SP
    PRI   TURBO        CTCSS             DATA
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT
    L/O                DELAY                ATT
    12
    4
    75
    8
    03
    6
    9
    E
    A
    FB
    GC
    HD
    IE
    JFREQ
    CHAN
    LOCKSQUELCH
    VOLUME
    OFF
    BC XLT9000
    TWIN TURBO
    SRC AUTOHOLD
    LIMITPRI   TURBO        CTCSS             DATA
    L/O                DELAY                ATT
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT12
    4
    75
    8
    03
    6
    9
    E
    FREQ
    CHAN
    LOCK
    Search, Mode, and Numeric Keys,
    and Rotary Tuning Controls
    5 . 0KHz ch 230
    NFM 46.0550MHz
    5 . 0KHz ch 230
    NFM 47.9450MHz
    5 . 0KHz ch 230
    L/O 46.0550MHz
    5 . 0KHz ch 230
    NFM 46.0550MHz 
    						
    							Unlocking All Frequencies
    1. Presshto stop the search.
    2. Find any locked-out frequency.
    3. Press and holdLfor two
    seconds.
    You hear a double beep when all frequencies are unlocked.
    Birdies
    Birdies are internally generated frequencies that cause the scanner to
    stop during search. If you have problems with these frequencies, use the
    lockout features to keep the scanner from stopping.
    Birdie Frequencies in MHz
    32.000 428.5875
    74.200 431.9875
    128.000 443.9375
    139.995 447.9875
    140.000 471.9875
    167.995 483.9250
    171.250 511.9250
    312.4375 794.5500
    312.4625 811.9750
    383.9875 967.9125
    407.9875 967.9875
    415.9375 1084.0625
    423.5875 1084.1375
    423.9875
    33
    5 . 0KHz ch 230
    L/O 47.2250MHz
    5 . 0KHz ch 230
    NFM 47.2250MHz 
    						
    							Additional Scanner Features
    Use these keys:
    Scanning Weather Channels
    The BC9000XLT is not preprogrammed with NOAA Weather frequencies.
    See the Betty Bearcat Frequency Guide for a list of weather frequencies in
    your area. Then, see page 11 of this Operating Guide to program the
    frequencies into the BC9000XLT.
    Using Data Skip
    Some frequencies carry un-modulated signals or data signals (such as
    pager preamble signals or telefax signals). You can set the scanner to
    continue scanning after a 3-second delay, when it encounter such signals.
    Pressdto turn Data Skip ON.
    Note:
    Data Skipis not available for the AM band and is not active
    during Priority scan.
    Note:You can turn
    Data Skipon or off at any time during scanning,
    searching and during Auto Store.
    34
    COUNT         AUX          STATUS
    SCAN
    SRCMANUAL
    AUTO PROG SEND ALPHA
    HOLD
    LIMIT MEM SHIFT
    LINEEXT SP
    PRI   TURBO        CTCSS             DATA
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT
    L/O                DELAY                ATT
    12
    4
    75
    8
    03
    6
    9
    E
    A
    FB
    GC
    HD
    IE
    JFREQ
    CHAN
    LOCKSQUELCH
    VOLUME
    OFF
    BC XLT9000
    TWIN TURBO
    SRC AUTOHOLD
    LIMITPRI   TURBO        CTCSS             DATA
    L/O                DELAY                ATT
    COUNT         AUX          STATUS
    PROG SEND ALPHAMEM SHIFT
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT12
    4
    75
    8
    03
    6
    9
    E
    Status, Search, Mode, Numeric and Special Function Keys 
    						
    							Changing the Frequency Step
    The frequency step is the minimum space between frequencies in the
    Manual or Search Mode.
    Your scanner is pre-programmed with a default frequency step for each of
    its frequency bands. You can override the default frequency step to
    search in larger or smaller increments when searching, during Auto Store,
    or when stepping through frequencies withh,l, or the Rotary
    Tuner.
    1. Presshto stop the
    search.
    2. Pressf.
    3. Press the desired step on the
    numeric keypad.
    Example:Press).
    To return to the original frequency
    step, press?twice.
    35
    5 . 0KHz ch 230
    NFM 48.0000MHz
    50 . 0KHz ch230
    STEP:50.0KHz
    5 0 .0KHz ch 230
    NFM 48.0000MHz
    5 . 0KHz ch 230
    NFM 48.0000MHz 
    						
    							Setting the Signal Mode
    Your scanner is capable of receiving three signal modes:
    AM Amplitude Modulation
    NFM Narrow Frequency Modulation
    WFM Wide Frequency Modulation
    Each of the scanner’s frequency bands is pre-programmed with a default
    signal mode. If you want to override the default signal mode for a
    particular frequency, use these keys:
    1. Pressf.
    2. Press the signal mode.
    Example:^.
    36
    COUNT         AUX          STATUS
    SCAN
    SRCMANUAL
    AUTO PROG SEND ALPHA
    HOLD
    LIMIT MEM SHIFT
    LINEEXT SP
    PRI   TURBO        CTCSS             DATA
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT
    L/O                DELAY                ATT
    12
    4
    75
    8
    03
    6
    9
    E
    A
    FB
    GC
    HD
    IE
    JFREQ
    CHAN
    LOCKSQUELCH
    VOLUME
    OFF
    BC XLT9000
    TWIN TURBO
    COUNT         AUX          STATUS
    PROG SEND ALPHAMEM SHIFT
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT12
    4
    75
    8
    03
    6
    9
    E
    Status, Numeric and Special Function Keys
    MODE : WFMSRC WFM 5.0KHz
    T
    SRC WFM 5 . 0 KHz
    MHz 46.6000T 
    						
    							Using Signal Attenuation
    When theATTLED is on, the incoming signal strength is attenuated
    (reduced) by about 15 dB. This prevents unusually strong signals from
    over-loading the scanner.
    In the Scan Mode, you must individually program each channel you want
    to use the Signal Attenuation feature. You can use the Signal Attenuation
    feature in the Manual, Search, or Scan Mode.
    Use these keys:
    While Scanning:
    1. Pressm.
    2. PressT. The display does not change.
    While Searching, pressT.
    37
    COUNT         AUX          STATUS
    SCAN
    SRCMANUAL
    AUTO PROG SEND ALPHA
    HOLD
    LIMIT MEM SHIFT
    LINEEXT SP
    PRI   TURBO        CTCSS             DATA
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT
    L/O                DELAY                ATT
    12
    4
    75
    8
    03
    6
    9
    E
    A
    FB
    GC
    HD
    IE
    JFREQ
    CHAN
    LOCKSQUELCH
    VOLUME
    OFF
    BC XLT9000
    TWIN TURBO
    PRI   TURBO        CTCSS             DATA
    L/O                DELAY                ATTSCANMANUAL
    Bank D ch 83
    855.9125MHz 
    						
    							Preventing Accidental Programming
    The BC9000XLT has a lock feature to
    prevent accidental programming
    entries. To disable thee,P,
    N, andUkeys, move the rear
    panel switch to ON.
    When you presse,P,N,
    orU, a message appears.
    Using COUNT to Monitor Channel Activity
    The Count feature counts the number of times scanning stops on an
    active channel. Use Count to determine the amount of activity on
    channels during a scanning session.
    Use these keys:
    1. Pressm.
    2. Pressc.
    38
    ENTER LOCKOFF ON
    Bank C ch 69
    ENTER LOCKED
    COUNT         AUX          STATUS
    SCAN
    SRCMANUAL
    AUTO PROG SEND ALPHA
    HOLD
    LIMIT MEM SHIFT
    LINEEXT SP
    PRI   TURBO        CTCSS             DATA
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT
    L/O                DELAY                ATT
    12
    4
    75
    8
    03
    6
    9
    E
    A
    FB
    GC
    HD
    IE
    JFREQ
    CHAN
    LOCKSQUELCH
    VOLUME
    OFF
    BC XLT9000
    TWIN TURBO
    SRC AUTOHOLD
    LIMIT
    COUNT         AUX          STATUS
    PROG SEND ALPHAMEM SHIFT
    SCANMANUALBRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT12
    4
    75
    8
    03
    6
    9
    E
    FREQ
    CHAN
    LOCK
    Scan, and Mode Keys
    Bank A P  ch 1
    482.7625MHz
    Count : 01P ch 1
    482.7625MHz 
    						
    							3. Pressm,, or use the Rotary Tuner to see
    the count for each channel.
    Counter counts up to 99. To reset the counter for individual channels
    1. Pressm.
    2. Enter the channel number or
    use,orthe
    Rotary Tuner to select the
    channel.
    3. Press?twice.
    Note:Turning off power resets the counter for all channels.
    To turn COUNToff:
    1. Pressm.
    2. Select a channel with the Count
    feature ON.
    3. Pressc.
    39
    Count : 01P ch 1
    482.7625MHz
    Count : 01P ch 1
    482.7625MHz
    Bank A P  ch 1
    482.7625MHz
    Count : 00Pch
    1
    482.7625MHz 
    						
    							Displaying Bank Memory Status
    This feature shows the programming status of the channels in a bank.
    Use these keys:
    1. Pressm.
    2. Enter the channel number or
    use the Rotary Tuner to select
    any channel in the bank.
    3. Press and holdcfor two
    seconds.
    The display shows:
    The bank (AthroughJor0through9)
    An asterisk character (k) to represent each programmed
    channel.
    An underscore (_) character for an unprogrammed channel
    A“P” to designate a Priority channel
    An “L” to show a channel that is locked out.
    To check bank memory status in other banks, turn the Rotary Tuner to
    move from one bank to the next.
    To exit from this mode, pressmors.
    40
    COUNT         AUX          STATUS
    SCAN
    SRCMANUAL
    AUTO PROG SEND ALPHA
    HOLD
    LIMIT MEM SHIFT
    LINEEXT SP
    PRI   TURBO        CTCSS             DATA
    BRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT
    L/O                DELAY                ATT
    12
    4
    75
    8
    03
    6
    9
    E
    A
    FB
    GC
    HD
    IE
    JFREQ
    CHAN
    LOCKSQUELCH
    VOLUME
    OFF
    BC XLT9000
    TWIN TURBO
    COUNT         AUX          STATUS
    PROG SEND ALPHAMEM SHIFT
    SCANMANUALBRI             DIM             OFF
    AM            NFM            WFM
    5KHz      12.5 KHz      25KHz
    CLR          50KHz         HI-CUT12
    4
    75
    8
    03
    6
    9
    E
    FREQ
    CHAN
    LOCK
    Bank E ch 110
    854.9800MHz
    Bank E P
    –––L** * *L L _____________* 
    						
    All Uniden manuals Comments (0)

    Related Manuals for Uniden Bc9000xlt Wideband Scanner Owners Manual