Trillium Talk To 308 Installation Procedures Manual

INSTALLATIONCentral Off ice/PABX Line Connection
These lines are normally terminated by RJllC type
jacks. When requesting service from the telephone 
com-
pany, please request that the first two lines are terminatedwith an 
RJ14C type jack. Alternatively, if the lines are
already installed using RJllC type jacks, an adapter such
as an 
SE 2678 (Suttle Apparatus Corp.) will be required.
Where the connection is made directly from the CO.line 625 type jack to the KSU, use a four conductor
modular line...

INSTALLATIONDoor Answer OptionThe 
TalkTo 308 System will provide door signaling
and 2 way conversation with up to 2 doors. To provide thisoption, one door answer unit and a maximum of 2 door
modules are required.
The Door Answer Module is 
moulded in plastic,
measures 4 inches x 5 inches, and is fitted at the door
requiring intercom service.
Door
308 KSU
PlugIII
3.89” 
(99mm)1.57” (40mm)I*I_1Mount each of the door modules adjacent to the
door to be equipped with intercom service. The door
module...

INSTALLATION1’t---6.26” (lSSmm)-----rJThe Door Answer Module with front cover 
Jetachedshowing the two screw terminals.
Door Answer UnitThe Door Answer Unit (DAU) is mounted on the
backboard with the screws supplied. The Door Answer
Unit is connected with a modular 6 conductor cord sup-
plied with the Unit. At the KSU plug the 6 conductor cord
into the jack labeled 
Door. At the Door Answer Unit, plugthe cord into the jack labeled DA.
I 
)--5.78” (147mm)-+ I
Caution: If the Door Answer Unit is connected...

INSTALLATIONPower Failure Transfer Option
To provide Telephone service in the event of a com-
merical power outage, a Power Failure Transfer Unit (PFT)
must be installed. The PFT will allow all 3 of the 
TalkTo 308
system’s 
C.O./PABX lines to be transferred to 3 individualindustry standard 2 wire telephones when the commer-
cial power fails.Mount the PFT unit on the backboard near the
KSU. Install the 2 conductor special cable supplied with
the unit. At the KSU, plug one end into the jack markedPFUC. At...

INSTALLATIONPFUco 3
co 1.2
308 KSUCable Supplied with Power Fail Unit
/
DJ
PlugI3RJ 4 Wire Modular Line Cord
PlugPlug
c
I
IY
L
q
CNJT4TTK 3.4
T3TTK 1.2
T2Tco 3.4TIT
co 1.2
PowerFail TransferUnit
625 Type Jacks
C.O.IPAB; Linesq
Not Usedq -wMaximum 
1
0-p Per incoming Line
PPower Fail Telephone
Power Fail Transfer Option ConnectionsSystem Programming
Before programming the system, check that the
It is recommended that the system is programmed
customer has completed a Features 
Selection form. Aimmediately...

SYSTEM PROGRAMMINGSystem Requirements for Programming
For the system to be programmed to meet your re-quirements, it is necessary to decide what features are
needed, and what parameters are required for those
features selected. The following notes are intended to aid
you in choosing the correct features and parameters. For
reference purposes, please complete the accompanyingprogramming form.
(1) Hold Recall Time: Determines the time period
between putting a caller on hold and receiving a tone
reminder...

SYSTEM PROGRAMMING
Customer Feature Selection
Hold Recall (l)**Select 
ok item per Line
1 min 
IJ L min 0 3 min 0 No Recall Cl
Tone Duration 
(2)*I55ms a 75ms 0
Flash/Cancel(3)*Flash0250ms0500ms01set03set0Cancel 
GT500ms is recommended for calibrated flash
Pause on Number (4)
Yes 070809000
No 
FC.O./PABX LINE (5)
C.O. u1 Liz p-3 cPABX 
0102030
Incoming Call Only By Line (6)
Yes 
0No 
I2Line 1 
c3 Line 2 0 Line 3 Cl
Outgoing Call Restriction
By Station (7)
StnKlassYes 
I3
mi 11111 r;T;n W]No 
0Night...

SYSTEM PROGRAMMING
Preparation -
Before attempting to program the system, check
l Station 10 is connected.l The switches, Program 
7 and 2, are set of Off.
l The KSU is connected to a 
1lOV ac power supply.
l The status 
hdicator’on the KSU is flashing.
l The switch, Battery, is set to On.
l A Features Selection form, completed by the customer,
is available.
Note: Default data is automatically loaded as feature pro-gramming if the switches, Program 
7 and Program 2,
are set to On, and the Reset button is...

INDIVIDUAL FEATURE PROGRAMMINGFeatures need not necessarily be programmed in
a specific order. Each is accessed simply by entering the
specific 
3-digit access code. The following charts show theFeature, the Access Code the Access Keys and their
functions.Hold Recall 
- Pulse Duration
- Flash/Cancel
Access Code 010Default is 
- No recall
- 75ms
- FlashCaiibrated Flash/Cancel
Access Code 030Default is 
- 250ms
Feature DataC.O. 7C.O. 2co. 3holdmic.on/off
250msNotNotOffOff500msappk-applic-onOff1...

INDIVIDUAL FEATURE PROGRAMMINGOutgoing Call Resiric tion, Night
Transfer and Private Lines 
- By Station
Access Code 
1Xx(where XX is station number 10-17)
Default is - No Restriction, No Ringing, No Private Line
Sature DataC.O. 1
C.O.IPABX
Line
RestrictionsClass A
No
Restrictron
OffClass 
B- Dialing 0 +numberDralrng 1 +
numberDialing more
than 8 digitsonClass C
- Dialing an
outside lineOff
Nrght Transfer
No ringing
Ringing
Private Line
(only applies
to Line 1)
C.O. Line 1
No
C.O. 
Lrne 1Yes- a
Examples...