Toshiba Strata Xii, Strata Xx General Description Manual

a) External Page--the relay is activated when- 
ever the external page circuit is accessed. 
A “make” contact is provided for control 
of background music on external page. 
This is- required only when an external 
page amplifier is used. 
b) Night Relay Service-relay will provide a 
dry contact at the NR terminals on the 
front of the MPRU PCB. A strap option on 
the MPRU allows the NR relay to function 
in one of two modes: 
1) Answering Machine Control- if the 
strap remains intact, the relay is oper-...

TOSHIBA SYSTEM PRACTICES 
ELECTRONIC KEY TELEPHONE SYSTEM INSTALLATION 
SECTION 100-020-200 
JUNE 1983 
SGrata +’ - 
XII&xx 
INSTALLATION  

TOSHIBA SYSTEM PRACTICES INS IALLAI IUN 
ELECTRONIC KEY TELEPHONE SYSTEM 
INSTALLATlbN 
SECTION 100-020-200 
JUNE 1983 
PARAGRAPH 
TABLE OF CONTENTS 
SUBJECT PAGE 
TABLEofCONTENTS 
................................................... ..i 
ILLUSTRATION LIST ii .................................................... 
GENERAL ...................................................................................................................... 
PACKING.. ; 
MKSU LOCATION REQUIREMENTS...

TOSHIBA SYSTEM PRACTICES 
ELECTRONIC KEY TELEPHONE SYSTEM 
INSTALLATlON 
ILLUSTRATION LIST 
FIGURE SUBJECT 
1 
2 
3 
4 
5 
6 
7 
8 
9 
10 
11 
12 
13 
14 
15 
16 
17 
18 
19 
20 
21 
22 
23 
24 
25 
26 
27 
28 
29 
30 
31 
32 
33 
34 
35 
36 
37 
38 
39 
40 
41 
42 
43 
44 
45 
46 
47 
IN3 IHLLAI IUN 
SECTION 100-020-200 
JUNE 1983 
PAGE 
CRDUBATTERYSTRAP.. 
........................................ .._ 
... 1 
AMMUBArrERYSTRAP 
............................................... 1 
MSMUBATTERYSTRAP...

INSTALLATION 
SECTION 100-020-200 
JUNE 1983 
01 GENERAL 
01.01 This section describes the installation 
precedures necessary to ensure proper operation 
of the STRATA XII & XX systems. The instal- 
lation procedures for the two systems vary only 
in relation to size; all other factors are the same. 
02 PACKING 
02.01 When a STRATA system is received, 
examine all packages and carefully 
note any visible 
damage. If any damage is found, bring it to the 
attention of the delivery carrier and make the...

INSTALLATION 
SECTION 100-020-200 
JUNE 1983 
FIGURE 3-MSMU BATTERY STRAP 
03 MKSU LOCATION REQUIREMENTS 
03.00 Power Requirements 
03.01 
The STRATA MKSU (both XII & XX) 
requires 24 VDC. This is provided by the power 
supply (EPSA), which in turn requires power 
from a grounded 115 VAC outlet. The outlet 
should be separately fused and rated at 15 amps. 
03.02 
The same EPSA power supply is used 
with both STRATA systems. 
03.03 The 54-inch cord provided to connect 
the EPSA to the MKSU dictates the...

INSTALLATION 
SECTION 100-020-200 
JUNE 
1983 
1 Drilling Template 
1 Back Plate 
1 Side Plate A 
1 Side Plate B 
2 
Side Angles 
12 Binding-head Screws 
04.22 Be certain that all parts are included 
before proceeding. 
04.23 In addition to those items supplied 
in the MKWM kit, six fasteners, suitable for the 
type of wall chosen, must be supplied by the 
installer. The fasteners will 
the wall mount bracket and 
A typical fastener would be: 
l/4-in. Toggle Bolt 
l/4-in. Molly Fastener 
l/4-in. Lag...

INSTALLATION 
SECTION 100-020-200 
JUNE 1983 
d) 
e) 
holes in the back plate. Tighten them loosely 
so that approximately 3/8-in. gap remains be- 
tween the head of the fastener and the mount- 
ing surface. 
install the wall mount assembly by slipping 
the two keyholes in the back plate over the 
two fasteners installed in Step C. 
Install the lower two fasteners in the back 
plate and tighten all four fasteners securing 
the wall mount assembly. 
04.27 The MKSU must be prepared for wall 
mounting by...

b) 
: 
c) 
d) 
e) 
f) 
Cl) 
SECTION 100-020-200 
JUNE 1983 
Loosely attach the side angles to the lower system operations and battery-protected RAM 
sides of the MKSU by sliding their keyholes for system data storage are located on the 
over the previously mentioned screws. AMMU. 
Ensure that the side angles are properly aligned 
with the holes in the mounting bracket and 
that the two top holes are aligned with the 
holes in the mounting surface. CRDU: 
Fasten the MKSU to the mounting surface 
loosely,...

INSTALLATION 
SECTION 100-020-200 
JUNE 1983 
(each system uses only one MDSU). The MDSU 
serves up to two fully functional DSS consoles 
and two DSS consoles which are used as Busy 
Lamp Field terminals only. 
MSMU/S&J: 
The SCNU is required and mounts directly 
on the MSMU to form a single unit. This 
optional PC6 serves as an interface between 
the MKSU and a printer or storage device 
used for the SMDR feature. The PCB is equip- 
ped with an RS 232C-type interface (one 
per system). 
MOPU (MF/DP or...