Toshiba Strata Vie General Description Manual

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 10 
PROGRAM 06 
AUTOMATIC RELEASE ON HOLD ENABLE 
SET LED on. 
1) Lock in the 
SET switch on the HKSU . Station 17 REP LED on. 
System is in program mode. 
2) Depress them key on station 17. 
3) Dial 1 tj] on the dial pad. 
4) Refer to the System Record Sheet. 
Using the m keys, turn the associated 
LEDs on or off, as required. Each CO key/LED 
represents itself-that is, if CO 1 LED is on, 
CO 1 will have AROH during normal opera- 
tion. If CO...

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 11 
PROGRAM 07 
AUTOMATIC RELEASE ON HOLD (AROH) TIMING 
SET LED on. 
1) Lock in the 
SET switch on the HKSU Station 17 REP LED on. 
System is in program mode. 
2) Depress the m key on station 17. 
3) Dial D 0 on the dial pad. 
4) Refer to the System Record Sheet. 
Using the [r9 keys, turn the associated 
LEDs on or off, as required. Each CO key/LED 
represents itself-that is, if CO 
1 LED is on, 
CO -1 will have XB (crossbar) timing for 
AROH....

PROGRAlUlUlING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 12 
PROGRAM 0#8 
NIGHT RING OVER EXTERNAL PAGE 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
key on station 17. 
3) Dial B fl 1 on the dial pad. 
4) Refer to the System Record Sheet. 
This program assigns either Ring or No Rin 
for 
each CO line in night operation. Using the 
b 
l 
keys, turn the associated LEDs on or off, as 
required. Each CO key/LED represents itself- 
that is, if...

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1966 
TABLE 13 
PROGRAM 09 
SINGLE CO LINE (DIAL 9) GROUP SELECTION 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
m SPKR LED steady on. 
2) Depress the 
l 
3) Dial fl g on the dial pad. SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
4) Refer to the System Record Sheet. 
An X on the record sheet means the LED should 
Using them keys,...

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 14 
PROGRAM 09X 
FOUR CO LINE (DIAL 91,92,93,94) GROUP SELECTION 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
Normal functions halt on station 17. 
2) Depress the m key on station 17. 
SPKR LED steady on. 
3) Dial B u a on the dial pad. (X = 1, 2, 3 or 4 
SPKR LED flashes continuously. 
de ending upon the group bein 
Al b defined). Dial 
for “dial 91” group; 1 1 CO LEDs go on...

PROGRAMMlNG PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 15 
PROGRAM Q#9 
OPL LINE HUNTING 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the m - key on station 17. 
3) Dial 1 4 a on the dial pad. 
4) Refer to the System Record Sheet. 
Using the m keys, turn the associated LEDs 
on or off, as required. Each CO key/LED 
represents itself-that is, if COs 1 & 2 LEDs are 
on, an incoming call at CO2 will ring the CO 1 
OPL station if...

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 
1986 
TABLE 16 
PROGRAM 100 
TOLL RESTRICTION SYSTEM PARAMETERS 
(DIALING PLAN) ’ 
1 SET LED on. 
1) Lock in the 
SET switch on the HKSU. I 
Station 17 REP LED on. 
System is in program mode. 
2) Depress the mkey on station 17. Normal functions halt on station 17. 
SPKR LED steady on. 
3) Dial 0 1 m on the dial pad. SPKR LED flashes continuously. 
CO LEDs go on according to present data. 
4) Refer to the System Record Sheet. An X on the record sheet means...

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 
1986 
TABLE 17 
PROGRAM 101 
TOLL RESTRICTION DISABLE 
SET LED on. 
1) Lock in the SET switch on the HKSU. Station 17 REP LED on. 
System is in program mode. 
2) Depress the m . key on station 17. 
3) Dial 0 fl 0 on the dial pad. 
4) Refer to the System Record Sheet. 
This program either enables or disables the toll 
restriction for each CO line in the system. Each 
CO key/LED represents itself--that is, if CO 
I 
LED is on, toll restriction is not...

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
. 
TABLE 18 
PROGRAM 102 
FORCED ACCOUNT CODE CHECK 
SET LED on. 
1) Lock in the 
SET switch on the HKSU. 
/ key on station 17. 
2) Depress the 
l 
3) Dial 0 1 a on the dial pad. 
4) Refer to the System Record Sheet. 
This program determines whether Forced 
Account Codes will be checked on a CO-line- 
by-CO-line basis. Using themkeys, turn their 
associated LEDs on or off, as required. 
0 LED on = Forced Account Codes are checked. 
l Each CO key/LED...

PROGRAMMING PROCEDURES 
SECTION 300-006-300 
MAY 1986 
TABLE 19 
PROGRAM 103 
EQUAL ACCESS #l 
1 SET LED on. 
1) Lock in the 
SET switch on the HKSU. 
I Station 17 REP LED on. 
System is in program mode. 
LEDs as shown below. 
Initialized Data: Blank (AD4 flashing). 
X = LED on 
All LEDs off = no data 
memory. 
New data is stored, previous data is erased. 
6A) Return to Step 2 in order to continue 
with this program 
6B) Go to Step 2 in azther program table 
. . or . . . 
6C) Transfer data into working...