Toshiba Strata E Electronic Telephone User Guide

GENERAL INFORMATION 
BUlTON DESCRIPTIONS (continued) 
PRIVACY/NON-PRIVACY BUlTON m 
Allows selection of CO line privacy in a non-private system. 
REDIAL BUlTON m 
Redials the last telephone number dialed. 
REPERTORY BUTTON m 
Provides access to automatic dialing numbers. 
SAVE BUTTON m 
Saves telephone number during conversation and automatically 
redials that number when button is depressed in the idle state. 
SPEAKER BUlTON m 
Turns the speaker on/off. 
TONE BUTTON m 
Changes the outpulsing of the CO...

GENERAL INFORMATION 
LED INDICATIONS 
CO INCOMING CALL 
Aslowflash rate(Yz-sec. on -%sec. off) indicatesthe CO/PBX 
line on which the call is coming in. 
CONFERENCE 
Avery fast flash rate (10 impulses per second (IPS)) indicates the 
CO line presently in the Conference mode. Other stations’ LEDs 
also show same indication for that line. 
EXCLUSIVE HOLD 
A very fast flash rate (10 IPS) indicates the CO line is placed on 
Exclusive Hold. 
HOLD RECALL 
A quick flash rate matching the tones (2 IPS for 1 sec....

AUTOMATIC DIALING 
AUTOMATIC DIALING 
TO CALL AN AUTOMATIC DIALING NUMBER 
1) Lift the handset. 
2) Depress any available a line button. 
l Listen for dial tone. 
3) Depress the m (or the 1) button. 
4) Dial the 2-digit automatic dialing code for the desired tele- 
phone number. 
l Your system will automatically dial the number for you. 
5) Hang up when the call is completed. 
TO CHAIN DIAL AUTOMATICALLY 
Dials two or more automatic dialing numbers during one call. 
1) Lift the handset. 
2) Depress any...

P-TOSHIBA 
AUTOMATIC DIALING 
AUTOMATIC DIALING BlJlTONS 
PROGRAMMABLE OPTION 
After accessing a CO line, automatic dialing for telephone 
number storage and use is available by depressing thembutton 
instead of a 2-digit access code. Each m button stores one 
telephone number (up to 16 digits).* 
TO STORE A TELEPHONE NUMBER** 
1) Do not lift the handset. 
2) Depress thefl(or m) andp(or m) buttons, respectively. 
3) Depress the m button you wish to use. 
4) Dial the telephone number to be stored (16...

AUTOMATIC DIALING 
SAVED NUMBER REDIAL 
PROGRAMMABLE OPTION 
This feature enables you to store a dialed telephone number and 
later redial that number by pressing a single button. 
TO SAVE A TELEPHONE NUMBER 
1) Lift the handset. 
2) Obtain a dial tone. 
3) Dial the desired telephone number. 
4) Depress the m button. 
l The telephone number is saved for future use. 
TO DIAL A SAVED TELEPHONE NUMBER 
1) Lift the handset. 
2) Obtain a dial tone. 
3) Depress the m button. 
l Saved number will be...

p-TOSHIBA7 
AUTOMATIC DIALING 
TELEPHONE NUMBER STORAGE (continued) 
TO STORE A TELEPHONE NUMBER IN STATION AUTO- 
MATIC DIALING MEMORY* 
Automatic dialing telephone numbers can be stored by each 
station. 
1) Do not lift the handset. 
2) Depress the 1 and i buttons, respectively. 
3) Dial a 2-digit automatic dialing code. 
l Station codes run consecutively from 10 - 49. 
4) Dial the telephone number to be stored (16 digits maximum).** 
5) Depress the a button to record the number in memory. 
6) Repeat...

P-TOSHIBA 
AUTOMATIC DIALING 
* AND # TONE DIALING 
When the * or # tones must be output (for computer input service 
or other use), the Automatic Dialing feature must be disabled to 
permit manual dialing of the 1 and 1 buttons. (Applicable only if 
m and m buttons are not programmed.) 
TO OUTPUT * AND # TONES 
1) Lift the handset. 
2) Depress any available m line button. 
2) Dial any desired directory number. 
4) To enable * and # tones to be sent, depress p a. 
NOTE: 
Only manual dialing willbe...

CALL FUNCTIONS 
AUTO BUSY REDIAL m (XII,/XX, only) 
After reaching a busy outside number, the system will automati- 
cally redial that number at programmed intervals. 
TO USE AUTO BUSY REDIAL 
1) Lift handset. 
2) Depress any available CO line and dial the telephone number. 
l Receive busy tone. 
3) Depress m button or m 11. 
l ABR LED blinks. 
4) Hang up. 
5) At programmed intervals (30/60 seconds), the system will 
redial the number (15 times maximum). 
l With each attempt, if busy, ABR will reset for...

CALL FUNCTIONS 
AUTOMATIC CALLBACK (INTERCOM) (continued) 
2) Go on-hook. You may make other calls while waiting for the 
called station to become available. 
3) When the called station becomes idle: 
l Your telephone rings at a fast rate. 
4) Answer the call within 9 seconds to prevent the callback 
from being cancelled. 
l You hear a single tone. 
5) Proceed to voice announcement. 
6) Proceed with the conversation. 
NOTES: 
1. You may cancel the request anytime prior to the callback by 
depressing the...

CALL FUNCTIONS 
CALL FORWARD 
PROGRAMMABLE OPTION 
For intercom calls* (all calls will be forwarded). 
TO SET A CALL FORWARD 
1) Depress the m button or dial 11 a 0 . 
l CFD LED flashes. 
2) Dial the station number to which calls are to be forwarded. 
3) Depress the m button or dial 1. 
l CFD LED on steady. 
l Calls will be forwarded to stored station number. 
TO CANCEL A CALL FORWARD 
1) Depress the m button or dial B 110 I. 
l CFD LED goes off. 
“A CO line that only rings at your station will forward....