Toshiba Strata Dk14, Dk40i, Dk424 Installation And Maintenance Manual

Station Apparatus
Digital Add-on Module Installation
Strata DK I&M    5/999-29
Station Apparatus
Digital Add-on Module Installation
Install one or two DADM 2020s to a 2000-series digital telephone (only). 
©DK14 supports up to 8 DADMs
©DK40i supports up to 12 DADMs
The number of DADMs supported by the DK424 depends on the common control PCB:
©RCTUA supports 12 DADMs
©RCTUB supports 40 DADMs
©RCTUC/D supports 120 DADMs
©RCTUE/F supports 200 DADMs 
The DADM provides DSS buttons, speed dial 
buttons and CO...

Station Apparatus
Digital Add-on Module Installation
9-30Strata DK I&M    5/99
Figure 9-20 Digital Add-On-Module
ADM Programming
ADMs are programmed in Program*29.
Important!To activate the ADM, Program *29 must be entered for each telephone port 
equipped with an DADM.
See the Strata DK programming record sheets in the Strata DK Programming Manual for button 
defaults.
DIU & ADM
1Black Wire
to Pin 1
Black Wire to Pin 1
1
110
12P 1
P 2
DADM Cable
(Supplied with DADM)
P1 of Bottom PCBTelephone
 Base...

Station Apparatus
PC Attendant Console
Strata DK I&M    5/999-31
Station Apparatus
PC Attendant Console
A Strata DK system configured with RCTUB2 or RCTUBA/BB can support two Attendant 
Consoles, and systems with RCTUC1/D2 or RCTUC3/D3 can support four Attendant Consoles. 
The RCTUA1, RCTUA3, RCTUB1, or RCTUC/D1 do not support Attendant Consoles.
PC and conventional Attendant Consoles require RCTUB2 or RCTUC/D2 R 2 processors or 
RCTUBA/BB, RCTUC3/D3, RCTUE3/F3 R3 processors. 
The PC attendant console...

Station Apparatus
PC Attendant Console
9-32Strata DK I&M    5/99
ä
To install the PC attendant console
See Figure 9-21 on Page 9-32 and follow these steps:
1. Connect the RATI to the PC COM port a with a standard RS-232 cable. 
2. Use one-pair wiring to connect the MDF to an RJ11 jack at the attendant console location. If 
you need to use a long cable, use two-pair for more power.
3. Plug in the handset cradle to the RJ45-jack.
4. Plug in the headset (if needed) to the handset base.
5. After programming...

Station Apparatus
PC Attendant Console
Strata DK I&M    5/999-33
Station Apparatus
PC Attendant Console Programming
Program 03: Code 51 assigns the RATU PCB attendant console cabinet slot number.
Important!The RATU PCB takes up four station ports in software; each attendant console will 
be assigned one of the ports in consecutive order. Toshiba recommends installing the 
RATU PCB in the next highest slot number following the last station PCB installed–
do not skip slots. The first port number will be...

Station Apparatus
PC Attendant Console
9-34Strata DK I&M    5/99
©In Program *09 or 71, assign digits 3700 to port 024, and assign any other selected DID 
extension number(s) to port 025–note that when the DID extension number assigned to either 
console is dialed, calls will load share between consoles.
PC Attendant Console Software Installation
Step 1: Install the Software
The PC attendant console requires the installation of software on an IBM-compatible PC which 
has been connected to the RATI. See...

Station Apparatus
PC Attendant Console
Strata DK I&M    5/999-35
Station Apparatus
3. In the Telephony Drivers dialog 
box, if “ATT Telephone Telephony 
SP” is shown in the driver list, go 
to Telephony Setup below. 
Otherwise, click the Add button to 
display the Add Dialog screen.
4. From the Add Drivers dialog box, 
if “ATT Telephone Telephony SP” 
is in the list, then select it (it should 
be highlighted) and press Add.
5. If “ATT Telephone Telephony SP” is not listed, press Add and type...

Station Apparatus
PC Attendant Console
9-36Strata DK I&M    5/99
7. The Default Configuration button will close the DK424 PC Attendant Configuration screen. 
To make changes, select Setup again, then continue.
Default Key Assignments
From the DK PC Attendant Configuration screen, the Configure Keys button takes you to the DK 
PC Attendant Key Configuration screen.The default key assignments are defined for R2 and R3. 
These key assignments must match Program 59 of the DK. The Default Config button on...

Station Apparatus
PC Attendant Console
Strata DK I&M    5/999-37
Station Apparatus
Class of Service
The Class of Service settings 
should reflect the call states and 
features which are anticipated to be 
used the most often. 
1. From the DK424 PC Attendant 
Configuration screen, click the 
Class of Service button.
These contain two items from 
Program 10 for setting the 
operation for Tone First or Voice 
First when calling a [DN] on the 
system and for setting the system to 
support two or three Night...

Station Apparatus
PC Attendant Console
9-38Strata DK I&M    5/99
ä
To access System Settings
1. From the Main Menu, select Setup.
2. Click OK or enter a password.
Initially, you can click OK, without 
entering a password. Store a password 
if you need to ensure that these settings 
cannot be changed without 
authorization. Once a password is 
entered, you must enter that password 
to proceed.
System Settings
Once the password screen is entered, 
the System Settings menu is presented. 
The two menu items,...