Toshiba Satellite L450 L450d Pro Maintanance Manual

Error! Style not defined. Error! Style not defined.   4 Replacement Procedures  
4.18 LCD Module and Inverter Board 
Removing the LCD Module and Inverter Board 
Remove the LCD module and the inverter board according to the following procedures and 
Figure 4.36, 4.37, 4.38 and 4.39. 
1. Remove one M2x4 screw securing the inverter board and detach two cables con\
nected to 
the two ends of the inverter. Then remove the inverter board. 
 
 
M2×4*1 
Figure 4.36 Removing the Inverter Board 
 
Satellite...

4 Replacement Procedures Error! Style not defined. Error! Style not defined.   
2. Remove ten M2.5x4 screws securing the LCD module to the LCD cover assembly and 
detach one cable from camera. 
3.  Lift the LCD module out of the LCD cover assembly. 
M2.5×4*10 
 
 
Figure 4.37 Removing the LCD Module from the LCD cover assembly 
Satellite L450/Pro L450/L450D/Pro L450D Maintenance Manual  4-44  

Error! Style not defined. Error! Style not defined.   4 Replacement Procedures  
4. Remove six M2x3 screws according to the sequence indicated in Figure 4.38 o\
n each side 
of the LCD hinge assembly and then remove the LCD hinge assembly. 
  M2×3*6 
2
3
1 2
3
1
 
Figure 4.38 Removing the LCD Hinge Assembly 
5.  Turn the LCD module over and place it face down on a protective surface, such as a foa\
m 
pad. 
6.  Remove the tape and LVDS cable connector. Then detach the LVDS cable. 
 
Figure 4.39 Removing...

4 Replacement Procedures Error! Style not defined. Error! Style not defined.   
Satellite L450/Pro L450/L450D/Pro L450D Maintenance Manual  4-46 
NOTE:  
ICs are fragile. Use extreme care not to apply pressure to the ICs along\
 the edges of the LCD 
module. 
Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or 
regulations. 
The LVDS cable must be carefully peeled away before disconnecting it fro\
m the LCD panel. 
 
Installing the LCD Module and Inverter Board 
Install...

Error! Style not defined. Error! Style not defined.   4 Replacement Procedures  
4.19 Camera (BTO) 
Removing the Camera 
Remove the camera according to the following procedures and Figure 4.40. 
1. Pick the camera up from the LCD cover. 
 
Figure 4.40 Removing the camera 
 
Installing the Camera 
Install the camera according to the following procedures.  1. Put the camera in the correct position on the LCD cover. 
 
Satellite L450/Pro L450/L450D/Pro L450D Maintenance Manual  4-47  

4 Replacement Procedures Error! Style not defined. Error! Style not defined.   
4.20 Hinge Saddle 
Removing the Hinge Saddle 
Remove the hinge saddle according to the following procedures and Figure 4.\
41. 1.  Remove two M2.5x6 screws that secure the hinge saddles to the logic lower a\
ssembly. 
2.  Remove the hinge saddles from the logic lower assembly. 
 
 
M2.5×6*2 
Figure 4.41 Removing the Hinge Saddle 
 
Installing the Hinge Saddle 
Install the hinge saddle according to the following procedures....

Error! Style not defined. Error! Style not defined.   4 Replacement Procedures  
4.21 USB Board 
Removing the USB Board 
Remove the USB board according to the following procedures and Figure 4.42.\
 
1. Remove one M2.5x3 screw that secures the USB board to the logic lower assem\
bly. 
2.  Remove the USB board from the logic lower assembly. 
 
 
M2.5×3*1 
Figure 4.42 Removing the USB Board 
 
Installing the USB Board 
Install the USB board according to the following procedures. 
1.  Seat the USB board in...

4 Replacement Procedures Error! Style not defined. Error! Style not defined.   
4.22 RJ11 Jack 
Removing the RJ11 Jack 
Remove the RJ11 jack according to the following procedures and Figure 4.43.\
 
1. Pick up the RJ11 jack from the socket on the logic lower assembly and pull the cable out of 
the routing channel. 
 
Figure 4.43 Removing the FM Jack 
 
Installing the RJ11 Jack 
Install the RJ11 Jack according to the following procedures. 
1.  Seat the RJ11 jack in the socket on the logic lower assembly....

Appendix A    
Appendix A  Handling the LCD Module 
Precautions for handling the LCD module 
The LCD module can be easily damaged during assembly or disassembly. Observe the following 
precautions when handling it to prevent damaging it. 
 1. When installing the LCD module in the display assembly, make sure that you seat it so 
that it is properly aligned and maximum visibility of the display is maintained. 
 
 
2.  Be careful to align the holes at the four corners of the LCD module with the...

3. If the panel’s surface gets dirty or moist, wipe  it with cotton or a soft cloth. If it is still 
dirty, try breathing on the surface to create a light condensate and wip\
e it again.  
If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a 
soft cloth and then wipe the panel’s surface. Do not apply cleanser d\
irectly to the panel. 
CRT
Cleaner
 
 
4.  If water or other liquid is left on the panel’s surface for a long pe\
riod, it can change the 
screen’s tint or stain...