Toshiba Projector Tdp Ff1 User Manual

21

Preparations

  Notes
• Remove the battery if the projector is not in use, otherwise the battery will gradually 
discharge.
• When the battery capacity become less then 10%, the following message appears:
  The battery capacity is less than 10%
.
• Press any key to make the warning message disappear.
• When the projector runs out of the battery, it shuts down automatically after showing the 
message “The projector is shutting down”.
• The projector will work for approximate 2 hours with full charged...

22

Using the remote control
 Replace the lithium battery.
Be sure to align the battery according to 
the polarity.
  Remove the battery compartment.
 Insert the battery compartment.
 Battery
•  Before using the battery, please refer to the notes on .
•  If the remote control stops working, or if its range decreases, replace the battery with new one.
 The remote control
•  The remote control may fail to operate if the infrared remote sensor is exposed to bright  sunlight or fluorescent lighting.
•  Do...

23

Preparations

Placement
Placement Styles
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the 
Default setting menu , in accordance with your needs.
      Warning
• Always observe the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when 
placing the unit.
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection 
distance. (Projection sizes are approximate values for full-size picture with no...

24
Connection
Before connection
•  Read the owner’s manual of the device you are connecting to the projector.
•  Some types of computer cannot be used or connected to this projector.
•  Turn off the power of both devices before connecting.
•  The figures are sample connections. 
  Notes
•  Moving pictures played back on computers using DVD software may appear unnatural if it 
is projected with this projector, but it is not a malfunction.
•  When a HEADPHONE terminal is used, sound is not output from the...

25
Operations
Turning the power on and off
Connecting the power cord
1 Plug the power cord into the adaptor.
2 Insert the power cord connector into the DC IN socket of the 
projector or install the battery pack.
3 Switching the power on (I)
Switch the power button to turn on the projector, then the power indicator on the LED 
lights green, and the start-up screen appears.
 CAUTION
•  Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.• Do not look into the...

26

Basic operations
1 Turn on the power.
Turn on the power by following the instructions in “Turning the power on (I)” .
2 Activate the connected device.
Turn on and start the connected device such as a computer.
3 Press the INPUT button.
See remote control section on .
4 Adjust the focus.
Use the focus ring to adjust the focus.
5 Adjust the vertical projection angle.
Rotate the foot adjuster to adjust the vertical position of the projection image. See foot adjuster on .
6 Adjust the volume.
Adjust the...

27

Operations

Using handy features
Using auto setting (Only for computer input)
This function sets up the projector to the optimum state such as sampling 
phase, frequency and screen position, for each type of the input signal by 
using simple operations.
 Press the AUTOSET button on the remote control.
For computer input, the  icon will appear during processing. 
You can also enter AUTOSET / button on the projector.
  Note
•  The image may not be projected or auto adjustment/setting may not be...

28

Freezing the image (Freeze)
Projected image can be frozen. This function is used to pause video during a presentation, 
etc. 
 Press the FREEZE button on the remote control.
The picture pauses. (The Freeze function is released when pressing the FREEZE 
button again.)
  Notes
•  The  icon will appear while freeze is in effect.
•  Other operation will also release the freeze.
• Although an image is frozen on the projector, the pictures are running on the video 
or other equipment.
•  If you use this...

29

Operations

Connect the USB memory to the projector and select USB input
Current folder name
File list display
Thumbnail display
Information of 
the selected file
Selected jpeg file
Folder
To the upper level foler
Using USB Memory
 Turn off the power switch.
 Plug the USB memory to the USB port.
 Turn on the power switch.
 Press remote control’s [USB] key to select 
USB input.
You can change input as well by pressing [INPUT/
MENU] key on the projector for a short time.
  Notes
1. USB HDD or hub is...

30

Using USB Memory (continued)
Folders and jpeg files in current folder are displayed in file list display as following.
  folder name --- folder
  file name.jpg --- Jpeg file
Use  or  to change the selected file or folder.
Select a folder and press , the files in the folder start displaying .
Select a jpeg file and press
 , the slideshow starts from the selected file. 
Select  and press , and the files in the  folder start displaying.
When there are too many files or folders to be displayed in one page, the 
...