Toshiba Ikwb16aw Manual

51
IEEE 802.1x Advanced Mode
This function is not able to work at the time of WLAN connection of IK-W\
B16A-W.
Enable  this  function  if  your  network  environment  uses  IEEE  802.1x,  which  is  a  port-based  network 
access  control.  The  network  devices,  intermediary  switch/access  point/hub,  and  RADIUS  server  must 
support and enable 802.1x settings.
The  802.1x  standard  is  designed  to  enhance  the  security  of  local  area  networks,  which  provides 
authentication to network...

52
3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to an 802.1x enabled switch. The devices will then start the authentication automatically.
● The authentication process for 802.1x:
1. The  Certificate Authority  (CA)  provides  the  required  signed  certificates  to  the  Network  Camera  (the 
supplicant) and the RADIUS Server  (the authentication server).
2. A  Network  Camera   requests  access  to the  protected  LAN  using  802.1X   via a  switch...

53
QoS (Quality of Service) Advanced Mode
Quality of Service refers to a resource reservation control mechanism, w\
hich guarantees a certain quality 
to  different  services  on  the  network.  Quality  of  service  guarantees  are  important  if  the  network  capacity 
is  insufficient,  especially  for  real-time  streaming  multimedia  applications.  Quality  can  be  defined  as,  for 
instance, a maintained level of bit rate, low latency, no packet dropping, etc.
The following are the main...

54
QoS/DSCP (the DiffServ model)
DSCP-ECN  defines  QoS  at  Layer  3  (Network  Layer).  The  Differentiated  Services  (DiffServ)  model  is 
based  on  packet  marking  and  router  queuing  disciplines.  The  marking  is  done  by  adding  a  field  to  the 
IP  header,  called  the  DSCP  (Differentiated  Services  Codepoint).  This  is  a  6-bit  field  that  provides  64 
different class IDs. It gives an indication of how a given packet is to be forwarded, known as the Per Hop 
Behavior  (PHB)....

55
HTTP port / Secondary HTTP port: By default, the HTTP port is set to 80 and the secondary HTTP port is 
set to 8080. They can also be assigned to another port number between 1025 and 65535.\
 If the ports are 
incorrectly assigned, the following warning messages will be displayed:
To access the Network Camera on the LAN, both the HTTP port and secondary HTTP port can be used 
to access the Network Camera. For example, when the HTTP port is set to 80 and the secondary HTTP 
port is set to 8080, refer...

56
Note  that  as  JPEG  only  transmits  a  series  of  JPEG  images  to  the  client,  to  enable  the  two-way  audio 
function,  make  sure  the  video  mode  is  set  to  “MPEG-4”  on  the Audio  and  Video  Settings  page  and  the 
media  option  is  set  to  “Video  and Audio”  on  the  Client  Settings  page.  Please  refer  to  Client  Settings  on 
page 33 and Audio and Video Settings on page 64.Click 
  to  enable  audio  transmission  to  the  Network  Camera;  click   to  adjust  the...

57
RTSP Streaming
To  utilize  RTSP  streaming  authentication,  make  sure  that  you  have  set  a  password  for  the  Network 
Camera first; please refer to Security on page 38 for details.
Authentication:  Depending  on  your  network  security  requirements,  the  Network  Camera  provides  three 
types of security settings for streaming via RTSP protocol: disable, basic, and digest. 
If basic  authentication  is  selected,  the  password  is  sent  in  plain  text  format,  but  there  can  be...

58
If the RTP ports are incorrectly assigned, the following warning message will be d\
isplayed:
Multicast  settings  for  stream  1  ~  5:  Click  the  items  to  display  the  detailed  configuration  information. 
Select the Always multicast option to enable multicast for stream 1 ~ 5.
Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other 
hand, sends a stream to the multicast group address and allows multiple clients to acquire the stream at 
the...

59
Wireless LAN (IK-WB16A-W only)
SSID  (Service  Set  Identifier):  This  is  the  name  that  identifies  a  wireless  network. Access  Points  and 
wireless  clients  attempting  to  connect  to  a  specific  WLAN  (Wireless  Local Area  Network)  must  use  the 
same  SSID.  The  default  setting  is  “default”.  Note:  The  maximum  length  for  an  SSID  is  32  single-byte 
characters and cannot consist of “, , or blank spaces.
Wireless mode: Click on the pull-down menu to select from the...

60
2. WEP  (Wired  Equivalent  Privacy):  This  allows  communication  only  with  other  devices  with  identical 
WEP settings.
■ Authentication Mode: Choose one of the following modes. The default setting is “Open”. Open – Communicates the key across the network.
Shared – Allows communication only with other devices with identical WEP settings.
■ Key length: The administrator can set the key length to 64 or 128 bits. The default setting is “64 bits”.
■ Key format: Hexadecimal or ASCII. The fault...