Toshiba Ikwb16aw Manual

11
Disclaimer
We  disclaim  any  responsibility  and  shall  be  held  harmless  for  any  damages  or  losses  incurred 
by the user in any of the following cases:
1.  Fire,  earthquake  or  any  other  act  of  God;  acts  by  third  parties;  misuse  by  the  user,  whether intentional or accidental; use under extreme operating conditions.
2.  Malfunction  or  non-function  resulting  in  indirect,  additional  or  consequential  damages,  including but not limited to loss of expected income and...

12
Wireless LAN and Your Health
Wireless  LAN  products,  like  other  radio  devices,  emit  radio  frequency  electromagnetic  energy. 
The  level  of  energy  emitted  by  Wireless  LAN  devices  however  is  far  much  less  than  the 
electromagnetic energy emitted by wireless devices like for example mobi\
le phones.
Because  Wireless  LAN  products  operate  within  the  guidelines  found  in  radio  frequency 
safety  standards  and  recommendations,  TOSHIBA  believes  Wireless  LAN  is  safe...

13
Be  sure  to  use  only  the  supplied  AC  adapter.  Using  a  different  AC  adapter  may  cause  the 
camera  to  malfunction,  heat  up,  or  catch  fire.  Before  using  the AC  adapter,  carefully  read  and 
observe the Important Safeguards ( → page  5) and the notes below.
●  Plug  the AC  adapter  into  the  100-240V AC  outlet.  If  inserting  it  into  other  than  100-240V AC  outlet, it may result in electric shock or fire hazard.
●  Do  not  repair,  modify  or  disassemble  the AC...

14
Specifications
AC adapter (DSA-20P-10)
Power source      : 100-240V AC 50/60 Hz
Rated output       : 12V DC, 1.5 A
Ambient temperature guaranteed for performance
          : 32°F to 104°F (0°C to 40°C)
Storage temperature     : -4°F to 140°F (-20°C to 60°C)
Maximum external dimensions   : 1.42 x 1.85 x 2.93 inches (36 x 47 x 74.5 mm)
          (width x height x depth)
Cord length         : 72 inches (1828 mm) 

15
Package Contents
IK-WB16A
l 
IK-WB16A/IK-WB16A-W
l  
Warranty Card l
 
AC Adapter
l  
Quick Start Guide and Important 
    Safeguards
l  
CD-ROM
 Content:
 User's Manual
 Quick Installation Guide 
 Installation Wizard
Cord length: 72 inches (1828 mm)
l  
Antenna (IK-WB16A-W only)
l 
Ceiling Mount Brackets / Alignment sticker
NETWORK CAMERAModel: IK-WB16A / IK-WB16A-WQuick Start Guide and Important SafeguardsThis guide describes the hardware installation.
Refer to the user's manual (PDF file)...

16
Front Panel
Back Panel
General I/O Terminal Block
This  Network  Camera  provides  a  general  I/O  terminal  block  which  is  used  to  connect  external 
input / output devices. The pin definitions are described below.
● 12V DC is outputted from 1-pin only when connected to a power supply.
PinName
1 12V DC Output
2 Digital Output
3 Digital Input
4 Ground
Physical Description
W h e n   y o u   c o n n e c t  
or  disconnect  a  wire, 
use  the  orange  push-
button.
NO TE
Built-in Microphone
Lens...

17
The diagrams below apply when "Digital Input" is used for an alarm input.
Status LED
The LED indicates the status of the Network Camera.
ItemLED status Description
1 Steady Red
Power on and system booting
Red LED unlit Power off
2 Steady Red + Blinking Green every 1 sec.
Network connected (heartbeat)
Steady Red + Green LED unlit Network disconnected
3 Steady Red + Blinking Green every 2 sec. Audio mute (heartbeat)
4 Blinking Red every 0.15 sec. + Blinking Green every 1 sec. Upgrading Firmware...

18
WPS/Reset 
This button is used dual purposes.
WPS:  (IK-WB16A-W only)
Push  the  WPS  button  of  your  wireless  access  point.  Press  and  release  the  WPS  recessed 
button  on  the  back  of  the  camera  using  a  paper  clip  or  small  object. The  ESSID  and  encrypted 
key  of  the  wireless  access  point  will  be  sent  to  the  camera  and  the  wireless  LAN  settings  are 
complete.
The reset button is used to reset the system or restore the factory default settings. Occasionally,...

19
Network Deployment
In this user’s manual, “User” refers to whoever has access to the Network Camera, 
and “Administrator” refers to the person who can configure the Network Camera and 
grant user access to the camera.
Network Deployment is shown in the Quick Start Guide(QSG). Please refe\
r to page 18 of the 
QSG.
Setting up the Network Camera over the Internet
There  are  several  ways  to  set  up  the  Network  Camera  over  the  Internet. The  first  way  is  to  set 
up the Network Camera behind...

20
2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is 
    192.168.0.3, please forward the following ports for the Network Came\
ra on the router.
■ HTTP port
■ RTSP port
■ RTP port for audio
■ RTCP port for audio
■ RTP port for video
■ RTCP port for video
If you have changed the port numbers on the Network page, please open the ports accordingly 
on  your  router.  For  information  on  how  to  forward  ports  on  the  router,  please  refer  to  your 
router’s user’s...